• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.567-568
• /
• 2006

To investigate the recycle possibility of slurry for the oxide-chemical mechanical polishing (oxide-CMP) application, three kinds of retreated methods were introduced as follows: First, the effects on the addition of silica abrasives and the diluted silica slurry (DSS) on CMP performances were investigated. Second, the characteristics of mixed abrasive slurry (MAS) using non-annealed and annealed alumina ($Al_2O_3$) powder as an abrasive added within DSS were evaluated to achieve the improvement of removal rates (RRs) and within-wafer non-uniformity (WIWNU%). Third, the oxide-CMP wastewater was examined in order to evaluate the possible ways of reusing it. And then, we have discussed the CMP characteristics of silica slurry retreated by mixing of original slurry and used slurry (MOS).

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.235-239
• /
• 2001

In recent years, as Chemical Mechanical Planarization(CMP) has been routinely utilized in integrated circuit(IC) fabrication, the consumption of slurry, main consumable in a CMP process, is greatly increased. Thus the reprocess of CMP slurries has been actively considered in the industry to reduce cost-of-consumable (COC). The main purpose of this study was to recycle the used oxide slurry using filters as a new method. As a result, Ultra Fine(UF) Filter could distinguish silica from the used oxide slurry and Reverse Osmosis(RO) Filter could distinguish Deionized(DI) Water and chemistry from chemistry solution. The tetraethylorthosilicate removal rate was almost the same as the number of recycle polishing was increased, when it was modified by slightly adding new SS-12 slurry. The microscratch didnt found as the number of recycle polishing was increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.59-60
• /
• 2006

The slurry stability and removal rate during recycling of slurry in silicon wafer polishing was studied. Average abrasive size of slurry was not changed with recycling time, however, large particles appeared as recycling time increased. Large particles were related foreign substances from pad or abraded silicon flakes during polishing. The removal rate as well as pH of slurry was decreased as recycling time increased. It suggests that the consumption of OH ions during recycling is the main cause of decrease of removal rate. Therefore, it is important to control pH of slurry to obtain optimum removal rate during polishing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.109-112
• /
• 2003

Recently, CMP (Chemical mechanical polishing) technology has been widely used for global planarization of multi-level interconnection for ULSI applications. However, COO (cost of ownership) and COC (cost of consumables) were relatively increased because of expensive slurry. In this paper, we have studied the possibility of recycle of reused silica slurry in order to reduce the costs of CMP slurry. Also, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slurry. As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• KSBB Journal
• /
• v.14 no.4
• /
• pp.445-451
• /
• 1999

Glutathione production was carried out using mixed cells of E. coli TG1/pDG7 $\alpha$ and bakers yeast in an Aerated Slurry Bioreactor. Glutathione-producing enzymes were stable for 34 hours, yielding 4.6 mM glutathione in suspension reaction. Glutahione production with high density mixed cells was studied as a function of flow rate in an Aereated Slurry Bioreactor. Glutathione concentration was higher than that in suspension reaction for 32 hours at the substrate feeding rate of 5.2 mL/hr with cell recycle in continuous Aerated Slurry Bioreactor. It was for 42 hours at 2.6 mL/hr and 22 hours at 5.2 mL/hr without cell recycle. Glutahione productivity was 25.7 mg/g wet $cell{\cdot}hr$ at the substrate feeding rate of 10.4 mL/hr with cell recycle, but 5.28 mg/g wet $cell{\cdot}hr$ at 5.2 mL/hr and 1.65 mg/g wet $cell{\cdot}hr$ at 2.6 mL/hr without cell recycle. Effective production time increased from 25 to 45 hours, by using a surfactant, tween 80. As a purfing gas, nitrogen was tested instead of air to avoid a possible oxidizing effect on glutathione-producing enzymes, resulting in the increase of effective production time to 40 hours.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.723-726
• /
• 2004

In this work, we have studied the CMP characteristics by mixing of original slurry and used slurry in order to investigated the possibility of recycle of used silica slurry. The removal rate and within-wafer non-uniformity (WIWNU) were measured as a function of different slurry composition. Also, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and the original slurry. Our experimental results revealed comparable removal rate and good planarity with commercial products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.145-148
• /
• 2003

Recently, the recycle of CMP (chemical mechanical polishing) slurries have been positively considered in order to reduce the high COO (cost of ownership) and COC (cost of consumables) in CMP process. Among the composition of slurries (buffer solution, bulk solution, abrasive particle, oxidizer, inhibitor, suspension, antifoaming agent, dispersion agent), the abrasive particles are one of the most important components. Especially, the abrasive particles of slurry are needed in order to achieve a good removal rate. However, the cost of abrasives, is still very high. In this paper, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size and hardness. Also, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slury, As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.50-53
• /
• 2003

CMP (chemical mechanical polishing) process remained to solve several problems in deep sub-micron integrated circuit manufacturing process. especially consumables (polishing pad, backing film, slurry, pad conditioner), one of the most important components in the CMP system is the slurry. Among the composition of slurries (buffer solution, bulk solution, abrasive particle, oxidizer, inhibitor, suspension, antifoaming agent, dispersion agent), the abrasive particles are important in determining polish rate and planarization ability of a CMP process. However, the cost of abrasives is still very high. So, in order to reduce the high COO (cost of ownership) and COC (cost of consumables) in this paper, we have collected the silica abrasive powders by filtering after subsequent CMP process for the purpose of abrasive particle recycling. And then, we have studied the possibility of recycle of reused silica abrasive through the analysis of particle size and hardness. Also, we annealed the collected abrasive powders to promote the mechanical strength of reduced abrasion force. Finally, we compared the CMP characteristics between self-developed KOH-based silica abrasive slurry and original slurry. As our experimental results, we obtained the comparable removal rate and good planarity with commercial products. Consequently, we can expect the saving of high cost slurry.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.39-42
• /
• 2002

Recently, CMP (chemical mechanical polishing) technology has been widely used for global planarization of multi-level interconnection for ULSI applications. However, COO (cost of ownership) and COC (cost of consumables) were relatively increased because of expensive slurry. In this paper, we have studied the possibility of recycle of reused silica slurry in order to reduce the costs of CMP slurry. The post-CMP thickness and within-wafer non-uniformity(WIWNU) were measured as a function of different slurry composition. As a experimental result, the performance of reused slurry with annealed silica abrasive of 2 wt% contents was showed high removal rate and low non-uniformity. Therefore, we propose two-step CMP process as follows In the first-step CMP, we can polish the thick and rough film surface using remaked slurry, and then, in the second-step CMP, we can polish the thin film and fine pattern using original slurry. In summary, we can expect the saving of high costs of slurry.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.9
• /
• pp.759-764
• /
• 2003

Recently, CMP (chemical mechanical polishing) technology has been widely used for global planarization of multi-level interconnection for ULSI applications. However, COO (cost of ownership) and COC (cost of consumables) were relatively increased because of expensive slurry. In this paper, we have studied the possibility of recycle of roused silica slurry in order to reduce the costs of CMP slurry. The post-CMP thickness and within-wafer non-uniformity (WIWNU) wore measured as a function of different slurry composition. As an experimental result, the performance of reused slurry with annealed silica abrasive of 2 wt％ contents was showed high removal rate and low non-uniformity. Therefore, we propose two-step CMP process as follows , In tile first-step CMP, we can polish the thick and rough film surface using remaked slurry, and then, in the second-step CMP, we can polish the thin film and fine pattern using original slurry. In summary, we can expect the saying of high costs of slurry.