• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.93-98
• /
• 2006

The numerical analysis of the negative pressure porous gas bearings is presented. The pressure distribution is calculated using the finite difference method. The Reynolds equation and Darcy's equation are solved simultaneously. The air bearing stiffness and damping are evaluated using the perturbation method. Rectangular uniform grid is employed to model the bearing. The vacuum preloading is considered. The pressure in the vacuum pocket is assumed to be a constant negative pressure. The total load, stiffness, damping and flow rate are calculated fur several geometrical configurations and several values of negative pressure. It is found that too large vacuum pocket can result in negative total force.

• Advances in concrete construction
• /
• 제3권3호
• /
• pp.161-185
• /
• 2015

FRP confining is a widely used method for seismic retrofitting of concrete columns. Several studies investigated the stress-strain behavior of FRP confined concrete prisms with square and rectangular sections both experimentally and analytically. In some studies, the monotonic stress-strain behavior of confined concrete was investigated and compressive strength models were developed. To study the reliability of these models, thorough statistical tests are required. This paper aims to investigate the reliability of the presented models using statistical tests including t-test, wilcoxon rank sum test, wilcoxon signed rank test and sign test with a level of significance of 5%. Wilk Shapiro test was also employed to evaluate the normality of the data distribution. The results were compared for different cross section and confinement types. To see the accuracy of the models when there were no significant differences between the results, the coefficient of confidence was used.

• Wind and Structures
• /
• 제16권6호
• /
• pp.617-627
• /
• 2013

In wind load calculations based on pressure measurements, the concept of 'tributary area' is usually used. The literature has less guidance for a systematic computational methodology for calculating tributary areas, in general, and for scattered pressure taps, in particular. To the best of the author's knowledge, there is no generic mathematical equation that helps calculate the tributary areas for irregular pressure taps. Traditionally, the drawing of tributary boundaries for scattered and intensively distributed taps may not be feasible (a time and resource consuming task). To alleviate this problem, this paper presents a proposed numerical approach for tributary area calculations on rectangular surfaces. The approach makes use of the available coordinates of the pressure taps and the dimensions of the surface. The proposed technique is illustrated by two application examples: first, quasi-regularly distributed pressure taps, and second, taps that have scattered distribution on a rectangular surface. The accuracy and the efficacy of the approach are assessed, and a comparison with a traditional method is presented.

• Computers and Concrete
• /
• 제24권1호
• /
• pp.85-94
• /
• 2019

The ACI building code is allowing for higher strength reinforcement and concrete compressive strengths. The nominal strength of high-strength concrete columns is over predicted by the current ACI 318 rectangular stress block and is increasingly unconservative as higher strength materials are used. Calibration of a rectangular stress block to address this condition leads to increased computational complexity. A triangular stress block, derived from the general shape of the stress-strain curve for high-strength concrete, provides a superior solution. The nominal flexural and axial strengths of 150 high-strength concrete columns tests are calculated using the proposed stress distribution and compared with the predicted strength using various design codes and proposals of other researchers. The proposed triangular stress model provides similar level of accuracy and conservativeness and is easily incorporated into current codes.

• Current Optics and Photonics
• /
• 제6권3호
• /
• pp.332-336
• /
• 2022

Given a cubic space, it is easy to uniformly illuminate the floor with light sources placed on top. However, little has been reported about uniform illumination on walls with the same configuration of light sources. Here we present a luminaire consisting of nine light-emitting diodes (LEDs) with perfect Lambertian distribution, placed on the top as a 3 × 3 rectangular LED array. The distances between LEDs and tilt angles of each individual LED are adjustable and optimized by an annealing algorithm. After optimization, the array produces a rectangular illumination pattern on one wall with a uniformity of about 89%. Analysis shows that the tilt angles of individual LEDs are key parameters for uniform side illumination. In a scenario that is more practical, the tilt angles of all the LEDs are set to be the same, only decreasing the uniformity to 83%.

• 한국항공우주학회지
• /
• 제39권7호
• /
• pp.585-595
• /
• 2011

사각형 및 원형 출구 형상 synthetic jet의 수치적 연구를 통하여 유입류가 존재할 경우 평판에서의 유동 구조 및 유동 제어 효과를 분석하였다. 사각형 출구 형상의 경우, jet 직후에 강한 vortex가 생성되지만 주변에 적은 momentum을 공급하기 때문에 유입류 방향으로 갈수록 유동제어 효과가 감소하게 된다. 원형 출구 형상의 경우, 규칙적인 vortex의 형태가 slot 중앙부터 끝까지 나타나고 보다 멀리까지 jet vorticity의 영향이 미치게 된다. 유동제어 효과를 예상하기 위하여 위치 별 wall shear stress를 비교하였다. 이에 원형 출구 형상이 사각형 출구 형상보다 유동제어 효과가 더 클 것으로 판단된다. 또한 최적의 원형 출구 형상을 도출하기 위하여, hole gap과 diameter의 변화에 따른 유동 구조 및 유동 제어 효과를 비교 분석하였다. 그 결과, hole diameter와 gap를 고려하여 원형 출구 형상을 설계할 경우 유동제어 효과를 극대화 할 수 있음을 밝혔다.

• 대한기계학회논문집B
• /
• 제26권11호
• /
• pp.1622-1629
• /
• 2002

To enhance isothermal characteristics of glass-farming surface, a rectangular parallelepiped heat pipes was fabricated, tested, and analyzed. The working fluid was sodium and the wall material was stainless steel 304. The dimension of the heat pipe was 210 (L) $\times$ 140(W) $\times$ 92(H)mm. A lattice structure covered with screen mesh was inserted to promote return of working fluid. The bottom side of heat pipe was heated electrically and the top side was cooled by liquid circulation. The temperature distribution at the bottom surface was of major concern and was monitored to determine isothermal characteristics. A frozen start-up of rectangular parallelepiped liquid metal heat pipe was tested. The operating mode of the sodium heat pipe was affected by the temperature of cooling zone, input heat flux, and the operating temperature of heat pipe. The heat pipe operated in a normal fashion as long as the heat flux was over 5.78W/cm$^2$, and the inside wall temperature of condenser part was above 95$^{\circ}C$ The maximum temperature difference at the bottom surface was observed to be 32$^{\circ}C$ when the operating temperature of the heat pipe was operating normally around 50$0^{\circ}C$. The result showed that a sodium heat pipe was very effective in reducing significantly the temperature difference in the glass-forming surface.

• 대한기계학회논문집B
• /
• 제25권5호
• /
• pp.713-721
• /
• 2001

Characteristics of the conical vortices on the roof corner of a rectangular prism have been investigated by using a PIV(Particle Image Velocimetry) technique. The Reynolds number based on the free stream velocity and the height of the model was 5.3$\times$10$^3$. The mean, instantaneous velocity vector fields, vorticity fields, and turbulent kinetic energy distribution were measured for two different angles of attack, 30$^{\circ}$and 45$^{\circ}$. The PIV measurements clearly observed not only the conical main vortex and the secondary vortex but also the tertiary vortex which is firstly reported in this paper. Asymmetric formation of the corner vortex for the case of 30$^{\circ}$angle of attack produces relatively the high magnitude of vorticity and turbulent kinetic energy around the bigger vortex which generates the peak suction pressure on the roof. Fairly symmetric features of the roof vortex are observed in the case of 45$^{\circ}$angle of attack, however, the dynamic characteristics are proved to be asymmetric due to the rectangular shape of the roof.

• Wind and Structures
• /
• 제34권1호
• /
• pp.15-27
• /
• 2022

This work comes within the framework of the "Benchmark on the Aerodynamics of a Rectangular Cylinder" that investigates a rectangular cylinder of length-to-depth ratio equal to 5. The present study reports and discusses velocity fields acquired using planar Particle Image Velocitmetry for several angles of attack and Reynolds numbers. In particular, for a cylinder depth-based Reynolds number of 2 × 10⁴ and zero incidence angle, the flow features along the lateral (parallel to the freestream) upper and lower surfaces of the cylinder are reported. Using first and second order statistics of the velocity field, the main flow features are discussed, especially the size and location of the time-averaged flow structures and the distribution of the Reynolds stresses. The variation of the flow features with the incidence is also studied considering angles of attack up to 6°. It is shown that the time-averaged flow is fully detached for incidence higher than 2°. For an angle of attack of 0°, the effects of the Reynolds number varying between 5 × 10³ and 2 × 10⁴ are investigated looking at flow statistics. It is shown that the time-averaged location of the reattachment point and the shape and position of the time-averaged main vortex are mostly constant with the Reynolds number. However, the size of the inner region located below the time-averaged shear layer and just downstream the leading edge corner appears to be strongly dependent on the Reynolds number.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.93-100
• /
• 2007

The flow velocity distribution at inlet and exit of Diesel Particulate Filter(DPF) by fabricating L-shape connector with the DPF was measured using a Pitot-tube and 2-D transverse machine. An adaptor designed for making the Pitot tube probe access to the inlet and exit of the DPF was connected with the inlet and exit flange of the DPF, respectively. The Pitot tube which was mounted in the 2-D positioning machine could access to the inlet and exit of the DPF through the rectangular window of the adaptor. The L-shape connector in the DPF inlet has a flow guide which is a perforated steel pipe. The flow velocity distribution at the inlet of the DPF showed a chaotic velocity distribution which is different from that with a diffuser type connector. The velocity distribution at the exit of the DPF showed a crown shape which is similar to that of the diffuser type connector. The velocity distribution at the exit of DPF showed different patterns according to the air flow rate.