• Structural Engineering and Mechanics
• /
• 제52권3호
• /
• pp.595-601
• /
• 2014

For analysis of the plates and membranes by numerical or analytical methods, the question of choice of the system of functions satisfying the different boundary conditions remains a major challenge to address. It is to this issue that is dedicated this work based on an approach of choice of combinations of trigonometric functions, which are shape functions of a bended beam with the boundary conditions corresponding to the plate support mode. To do this, the shape functions of beam vibrations for strength analysis of the rectangular plates by Kantorovich-Vlasov's method is considered. Using the properties of quasi-orthogonality of those functions allowed assessing to differential equation for every member of the series. Therefore it's proposed some new forms of integration of the beam functions, in order to simplify the problem.

• 한국강구조학회 논문집
• /
• 제27권3호
• /
• pp.289-298
• /
• 2015

CFT 구조는 각형이나 원형강관에 콘크리트가 충전된 구조로서, 강관은 콘크리트를 구속하고 콘크리트는 강관의 좌굴을 방지함으로써 부재의 강성 및 강도를 증가시킬 수 있다. 이에 본 연구는 관통 다이아프램 충전개구부 형상이 각형CFT 기둥-보 접합부의 내력에 미치는 영향을 실험을 통해 확인한 후, 유한요소해석을 수행하여 실험 결과와 비교 검증했다. 이로써 각형CFT 기둥-보 접합부의 내력은 관통 다이아프램의 개구부 면적이 같을 경우 그 형상에 크게 영향을 받지 않으며, 관통 다이아프램과 보 플랜지의 접합부분 형상 및 치수가 동일하면, 보에 발생한 휨응력이 다이아프램을 통해 기둥으로 전달되고 있음을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.71-74
• /
• 2007

Substitution of the stacked antenna for the normally pressed antenna in the mobile phone was tried for the purpose of decreasing its size. However, reduced size resulted in the difficulties obtaining the targeted characteristics with the bandwidth over 70MHz. The cross-section of the vias in the low temperature co-firing ceramics process was studied to find out effects on the bandwidth characteristics. Circular and rectangular cross-section of the via beneath different types of antenna patterns were simulated. Better bandwidth characteristics were acquired for the larger diameter of the circular section and for the rectangular section as the cross-section area increased. From the viewpoint of the shape of the cross-section, rectangular area showed better characteristics than the circular area with the same longest length in the cross-section.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.833-839
• /
• 2003

The effects of stiffeners on the modal characteristics of rectangular plates are investigated. A modeling method for the modal analysis of rectangular plates with stiffeners is presented. A mass density Dirac's delta function is used to idealize the stiffeners mathematically. The equations of motion for the plates are derived and transformed into a dimensionless form. To confirm the accuracy of the method presented in this study, numerical result are obtained and compared to those of a commercial program. The mode shape variations due to some parameter variations are also exhibited.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.94-97
• /
• 2001

An inverse finite element approach is employed for more capability to design the optimum blank shape from the desired final shape with small amount of computation time and effort. For multi-stage deep-drawing processes, numerical analysis is extremely difficult to carry out due to its complexities and convergence problem as well as tremendous computation time. In this paper, multi-stage finite element inverse analysis is applied to multi-stage rectangular cup drawing processes to calculate intermediate blank shapes and strain distributions in each stages. Deformation history of the previous stage is considered in the computation. Finite element patches are used to describe arbitrary intermediate sliding constraint surfaces.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.158-161
• /
• 2000

An inverse finite element approach is employed for more capability to design the optimum blank shape from the desired final shape with small amount of computation time and effort. For multi-stage deep-drawing processes, numerical analysis is extremely difficult to carry out due to its complexities and convergence problem as well as tremendous computation time. In this paper, multi-stage finite element inverse analysis is applied to multi-stage rectangular cup drawing processes to calculate intermediate blank shapes and strain distributions in each stages. Finite element patches are used to describe arbitrary intermediate sliding constraint surfaces.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.50-53
• /
• 2008

The differential equations governing free vibrations of the elastic arches with rectangular hollow section are derived in polar coordinates, in which the effect of rotatory inertia is included. Natural frequencies is computed numerically for circular arches with both clamped ends and both hinged ends. The lowest four natural frequency parameters are reported, with the rotatory inertia, as functions of three non-dimensional system parameters: the breadth ratio, the thickness ratio and the shape ratio.

• 소성∙가공
• /
• 제10권5호
• /
• pp.389-395
• /
• 2001

An inverse finite element approach is employed for more capability to design the optimum blank shape from the desired final shape with small amount of computation time and effort. For multi-stage deep-drawing processes with large aspect ratio, numerical analysis is extremely difficult to carry out due to its complexities and convergence problem. as well as tremendous computation time. In this paper, multi-stage finite element inverse analysis is applied to multi-stage rectangular cup drawing processes to calculate intermediate blank shapes and strain distributions in each stages. Deformation history of the previous stage is considered in the computation. Finite element patches are used to describe arbitrary intermediate sliding constraint surfaces.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -3
• /
• pp.1523-1526
• /
• 2002

In this paper, we propose a method fur measuring the dimensions of an arbitrary object using geometric relationship between a perspective projection image and a rectangular parallelepiped model. For recognizing the vertexes of the rectangular parallelepiped surrounding an arbitrary object, the method adopts a strategy that derives the equations for vertex recognition from the geometrical relationships for image formation between 2D image and the rectangular parallelepiped model. extracts from 2D image with vertical view features (or junctions) of minimum quadrangle circumscribing an arbitrary shape object, and then recognizes vertexes from the features with the equations. Finally, the dimensions of the object are calculated from these results of vertex recognition. By the experimental results, it is demonstrated that this method is very effective to recognize the vertexes of the arbitrary objects.

• 열처리공학회지
• /
• 제18권2호
• /
• pp.105-111
• /
• 2005

In sheet metal forming, drawbeads are often used to control uneven material flow, which may cause defects such as wrinkles, fractures, surface distortion and springback. Appropriate setting and adjusting of the drawbead force is one of the most important parameters in sheet forming process control. Therefore in this study, drawbead test was performed at various bead surface treatment conditions to clarify the frictional characteristics between sheet and drawbead. Furthermore, the differences in drawing force between circular and rectangular shape beads have also been measured to estimate the effectiveness of bead shape on the material flow control. The results show that drawing and friction characteristic were strongly influenced by surface treatments of bead and bead shapes.