• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.81-88
• /
• 2011

The method is introduced for estimating the noise source contribution on the noise of PDP TV in a multiple-input system where the input sources may be coherent with each other. By the coherence function method, it is found that the biggest part of the noise source in the PDP TV noise is generated by the PCB boards which consume high power and produce high heat. This analysis is modeled as three-input/single-output system because the noise is generated by three main boards, X-board, Y-board, SMPS that are located close to each other. The coherence function method is proved to be useful tool for identifying of noise source. In this study, Transfer Path Analysis using MDSA is implemented to determine the quantitative noise contribution of each board for PDP TV with the rear case closed and with the rear case open. And the possibility of noise reduction is confirmed through the experimental method that isolates the most contributing board by adding sound-absorbing materials to it.

• 소성∙가공
• /
• 제23권6호
• /
• pp.357-362
• /
• 2014

The purpose of the current study is to predict the hardness distribution in steel products after hot stamping using a quench factor analysis(QFA) coupled with FE-simulations. QFA is a method to predict properties such as hardness and tensile strength based on time-temperature-property(TTP) curves and can determine properties based on the temperature histories. The constants($K_1{\sim}K_5$) of QFA were determined using hardness data obtained after various cooling rates. In the current study, a rear side member was selected for evaluation and FE-simulations were performed to obtain the temperature histories during hot stamping. The predicted temperature data were imported into the QFA to calculate the hardness distribution of the hot stamped parts. A hot stamping experiment of the rear side member was conducted to verify the predicted hardness. The simulation results show good agreement with the experimental measurements.

• Transactions on Electrical and Electronic Materials
• /
• 제14권4호
• /
• pp.203-207
• /
• 2013

P-type Si wafers were dipped in HF solution. The minority carrier lifetime (lifetime) increased after HF treatment due to the hydrogen termination effect. To investigate the film passivation effect, PECVD was used to deposit $SiN_x$ on both HF-treated and untreated wafers. $SiN_x$ generally helped to improve the lifetime. A thermal process at $850^{\circ}C$ reduced the lifetime of all wafers because of the dehydrogenation at high temperature. However, the HF-treated wafers showed better lifetime than untreated wafers. PERCs both passivated and not passivated by HF treatment were fabricated on the rear side, and their characteristics were measured. The short-circuit current density and the open-circuit voltage were improved due to the effectively increased lifetime by HF treatment.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권2호
• /
• pp.136-142
• /
• 2015

The shell and tube heat exchanger is an essential part of a power plant for recovering transfer heat between the feed water of a boiler and the wasted heat. The baffles are also an important element inside the heat exchanger. Internal materials influence the flow pattern in the bed. The influence of baffles in the velocity profiles was observed using a three-dimensional PIV (Particle Image Velocimetry) around baffles in a horizontal circular tube. The velocity of the particles was measured before the baffle and between them in the test tube. Results show that the velocity vectors near the front baffle flow along the vertical wall, and then concentrate on the upper opening of the front baffle. The velocity profiles circulate in the front and rear baffle. These profiles are related to the Reynolds number (Re) or the flow intensity. Velocity profiles at lower Re number showed complicated mixing to obtain the velocities and concentrate on the lower opening of the rear baffle as front wall. Numerical simulations were performed to investigate the effects of the baffle and obtain the velocity profiles between the two baffles. In this study, a commercial CFD package, Fluent 6.3.21 with the turbulent flow modeling, k-${\epsilon}$ are adopted. The path line and local axial velocities are calculated between two baffles using this program.

• 오토저널
• /
• 제15권1호
• /
• pp.100-106
• /
• 1993

This paper aims to synthesize the research on fatigue fracture mechanisms of high strength aluminum alloys which are widely used in motorcars or airplanes to prevent accidents. To measure the data of crack opening ratio, the same materials and method are used for evaluating the fatigue crack propagation rate as an effective stress intensity factor. But, many researchers have brought different results. An exact crack opening ratio was, therefore, proposed for getting a more accurate fatigue crack propagation rate. The main conclusions obtained are as follows. (1) As a result of the fatigue test, the value of the crack opening ratio is the same regardless of the stress ratio. (2) The value of crack opening ratio is different according to the measuring point. After measuring the crack propagation rate by using an effective stress intensity factor, the crack opening ratio value measured at the crack mouth by a clip gage, or measured rear of the specimen by a strain gage is more accurate than that by any other measuring test.

• 한국지능시스템학회논문지
• /
• 제26권2호
• /
• pp.153-159
• /
• 2016

본 논문는 대각선 주행이 가능한 전방향 퍼스널 모빌리티의 메커니즘을 제안한다. 현대 사회에서 이동성은 인간의 기본적인 활동을 영위하는데 수반되는 전제조건이다. 퍼스널 모빌리티는 새로운 이동수단으로 자동차와 동일한 바퀴구조를 가지고 있으며 이동성 역시 자동차와 유사하다. 최근 노약자와 교통약자를 위한 퍼스널 모빌리티도 4륜 전동카트가 널리 보급되었다. 일반적으로 전동카트는 주행경로를 변경할 때 차체는 조향하는 방향으로 회전하며 이 때 곡률반경에 따른 충분한 공간을 확보해야 한다. 제안하는 퍼스널 모빌리티는 대각선 주행이 가능해지면서 이동성의 한계를 극복할 수 있다. 또한 주행경로에 장애물이 존재하거나 건물내부와 같은 좁은 공간에서도 주행이 가능해지면서 교통약자도 다양한 주행환경을 극복할 수 있다. 이 논문에서는 제안하는 퍼스널 모빌리티의 메커니즘과 개발한 퍼스널 모빌리티의 조향성능을 실험하고 대각선 주행이 가능함을 입증한다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.179-184
• /
• 2005

In the present study, conceptual design of the main wing for 20 seats WIG{wing in Ground Effect) flight vehicle, which will be a high speed maritime transportation system for the next generation, was performed. The high stiffness and strength Carbon-Epoxy material was used for the major structure and the skin-spar with a foam sandwich structural type was adopted for improvement of lightness and structural stability. As a design procedure for this study, firstly the design load was estimated with maximum flight load, and then flanges of the front and the rear spar from major bending load and the skin structure and the webs of the spars were preliminarily sized using the netting rules and the rule of mixture. In order to investigate the structural safety and stability, stress analysis was performed by Finite Element Codes such as NASTRAN/PA TRAN[6] and NISA II [7]. From the stress analysis results, it was confirmed that the upper skin structure between the front spar and rear spar was very unstable for the buckling. Therefore in order to solve this problem, a middle spar and the foam sandwich structure at the upper skin and the web were added. After design modification, even thought the designed wing weight was a little bit heavier than the target wing weight, the structural safety and stability of the final design feature was confirmed. Moreover, in order to fix the wing structure at the fuselage, the insert bolt type structure with six high strength bolts was adopted for easy assembly and removal.

• 한국건설관리학회:학술대회논문집
• /
• 한국건설관리학회 2008년도 정기학술발표대회 논문집
• /
• pp.855-858
• /
• 2008

경량기포혼합토는 경량성으로 인해 구조물등에 작용하는 하중이 저감되어 연약지반의 뒷채움 재료로 사용되지만, 일반토사에 비하여 초기시공비용이 많이 소요되어 아직 국내에서는 적용하고 있지 않다. 주로 뒷채움 재료는 초기시공미가 적게 소요되는 일반토사를 사용하고 있으나, 일반토사의 덧씌우기 공법은 횟수가 증가함에 따라 사용연수가 감소된다. 특히 연약지반에 설치된 BOX구조물이나 교대 뒷채움 인근의 단차 발생 시 덧씌우기 공법은 일시적인 대체공법은 가능하지만, 덧씌우기 두께에 대한 하중만큼 추가 하중이 발생하게 되므로 결국 단차에 대한 해결책은 되지 못한다. 따라서 본 연구에서는 BOX구조물 뒷채움 재료인 일반토사와 경량기포혼합토의 두 가지 대안에 대하여 LCC 분석을 실시하며, 경제적 측면에서 보다 합리적인 의사결정을 할 수 있는 경제성 분석을 제시하고자 하였다. 그 결과 경량기포혼합토가 일반토사에 비해 초기시공비용은 많이 소요되지만 유지관리 측면에서는 비용이 더 적게 소요되어, 6년 이내에 경제성을 확보할 수 있는 것으로 분석되었다.

• ETRI Journal
• /
• 제35권4호
• /
• pp.587-593
• /
• 2013

We demonstrate semitransparent organic photovoltaics (OPVs) based on thin metal electrodes and polymer photoactive layers consisting of poly(3-hexylthiophene) and [6,6]-phenyl $C_{61}$ butyric acid methyl ester. The power conversion efficiency of a semitransparent OPV device comprising a 15-nm silver (Ag) rear electrode is 1.98% under AM 1.5-G illumination through the indium-tin-oxide side of the front anode at 100 $mW/cm^2$ with 15.6% average transmittance of the entire cell in the visible wavelength range. As its thickness increases, a thin Ag electrode mainly influences the enhancement of the short circuit current density and fill factor. Its relatively low absorption intensity makes a Ag thin film a viable option for semitransparent electrodes compatible with organic layers.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.12.1-12.1
• /
• 2011

최근 p-type 결정질 실리콘 태양전지의 광열화현상(light induced degradation)에 대한 관심이 높아지면서, 이를 해결하기 위한 많은 연구들이 수행되고 있다. 본 연구에서는 LID 현상을 원천적으로 제거 할수 있는 n-type 기판을 이용하여, 상업적으로 양산화 가능한 공정을 도입하고, 시뮬레이션을 통하여 고효율화 방안을 제시하고자 한다. 이를 위해 일반적인 p-type 결정질 실리콘 태양전지 제작 공정을 사용하여 알루미늄이 도핑된 후면 에미터 구조의 n-type 결정질 실리콘 태양전지를 제작하였으며, PC1D 시뮬레이션을 통해서 n+/n/p+구조의 n-type 결정질 실리콘 태양전지의 에너지 변환 효율 향상을 위한 방안을 제시하였다.