• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.8
• /
• pp.844-851
• /
• 2005

The purpose of this study was to determine feasibility of application of regenerated or recycled $TiO_2$ on the successive treatment of Cu(II)-EDTA. The recovery of copper, the reuse of $TiO_2$ and the assessment of acute toxicity was studied in the total eight successive photocatalytic reactions. Aqueous solution of $10^{-4}\;M$ Cu(II)-EDTA was treated using an illuminated $TiO_2$ at pH 6 in a circulating reactor. Two different procedures were applied in the reuse of $TiO_2$: i) recycle of $TiO_2$ without acid wash ii) regeneration of $TiO_2$ with acid wash to remove adsorbed copper in a previous experiment. The averaged decomplexation rate constant($k'_{obs}$) of Cu(II)-EDTA in recycle of $TiO_2$ without acid wash was approximately 45% less than that in regeneration of $TiO_2$ with acid wash. Removal of Cu(II) was near complete after 180 minutes in the total eight successive photocatalytic reactions using the regenerated $TiO_2$ after acid wash. In contrast, removal of Cu(II) was minimum at total fifth successive photocatalytic oxidation using the recycled $TiO_2$ without arid wash. The recovered $TiO_2$ was approximately 86% in average in each procedure. The recovered Cu(II) was 67.9% in average. The acute relative toxicity of the treated water rapidly declined at an initial reaction time up to 60 minutes but little declination was observed after 60 minutes due to little degradation of DOC. Relative toxicity of treated water using the recycled $TiO_2$ without acid wash we some what well correlated with the concentration of dissolved Cu(II). From this work, it is suggested that Cu(II)-EDTA can be effectively treated using an integrated cyclic photocatalytic oxidation with recovery of $TiO_2$ and Cu(II).

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.11
• /
• pp.1038-1045
• /
• 2010

In this study, the anaerobic ultimate biodegradability and multiple decay rate of organic matter were evaluated according to various salt concentrations in seafood processing wastewater. The evaluation was also performed with various types of anaerobic bacteria and S/I (substrate/inoculum) ratios. After the S/I ratio was fixed at 0.9, the ultimate biodegradability values of the anaerobic digested sludge and granular sludge were became 72.0% and 92.0%, respectively. The multiple decay rate coefficients ($k_1$) coefficients of the anaerobic digested sludge and granular sludge were $0.0478{\sim}0.1252\;day^{-1}$ and $0.0667{\sim}0.1709\;day^{-1}$, respectively. The optimum S/I ratio of the seafood wastewater, which was determined based on the ultimate anaerobic biodegradability and gas production, was 0.9. The organic matter removal rate never became less than 85.0% under a 3,000 mg/L chloride concentration. The multiple decay rate coefficients ($k_1$) were $0.1603{\sim}0.1709\;day^{-1}$ under $3,000\;mgCl^-/L$, and $0.0492{\sim}0.0760\;day^{-1}$ in more than $6,000\;mgCl^-/L$. The multiple decay rate coefficients ($k_2$) were $0.0183{\sim}0.0348\;day^{-1}$ under $6,000\;mgCl^-/L$, and $0.0154\;day^{-1}$ at $9,000\;mgCl^-/L$. With increasing chloride concentrations, the reaction rate ($k_1$, $k_2$) and ratio of the rapidly degraded organic matter ($S_1$) decreased.

• Microbiology and Biotechnology Letters
• /
• v.1 no.1
• /
• pp.51-57
• /
• 1973

2,2'-Methylene bis (3,4,6-trichloroacetoxy benzene) had been synthesized from Hexachlorophene. The eleven new derivatives -(2,2'Methylene bis [3,4,6-trichloro o-(${\beta}$-anilinopropionoxy) benzene]: m. p 173∼4$^{\circ}C$, C$\_$31/H$\_$24/N$_2$O$_4$Cl$\_$6/, 2,2' Methylene bis [3,4,6-trichloro (${\beta}$-Cyclohexylaminopropionoxy) benzene]: M. P, 187∼8$^{\circ}C$, C$\_$31/H$\_$36/N$_2$O$_4$Cl$\_$6/, 2,2'-Methylene bis [3,4,6-trichloro (${\beta}$-phenyl hydrazinopropionoxy) benzene]; M. P. 151∼3$^{\circ}C$, C$\_$33/H$\_$28/N$_2$O$_4$Cl$\_$6/, 2,2'-Methylene bis [3,4,6-trichloro (${\beta}$-o-toluidinopropionoxy) benzene]: M. P. 172∼3$^{\circ}C$, C$\_$33/H$\_$28/N$_2$O$_4$Cl$\_$6/, 2,2'-Methylene bis [3,4,6-trichloro (${\beta}$-p-todudinopropionoxy) benzene]: 153∼4$^{\circ}C$, C$\_$33/H$\_$28/N$_2$O$_4$Cl$\_$6/, 2,2'-Methylene bis [3,4,6-trichloro (${\beta}$-o-chloro anilinopropionoxy) benzene]: 170∼2$^{\circ}C$, C$\_$31/H$\_$27/N$_2$O$_4$Cl$\_$8/, 2,2'-Methylene bis [3,4,6-trichloro (${\beta}$-p-sulfamilinopropionoxy) bengene]: M. P. 310-5$^{\circ}C$, C$\_$31/H$\_$24/N$_2$S$_2$O$\_$10/Cl$\_$8/, 2,2'-Methylene bis [3,4,6-trichloro (${\beta}$-piperidinopropionoxy) benzene]: M. P. 168∼2$^{\circ}C$, C$\_$29/H$\_$32/N$_2$O$_4$Cl$\_$6/, 2,2'-Methylene bis (3,4,6-trichloro (${\beta}$-morpholinopropionoxy) benzene]: M. P. 226∼8$^{\circ}C$, C$\_$27/H$\_$28/N$_2$O$\_$6/Cl$\_$6/, 2,2'-Methylene bis (3,4,6-trichloro (${\beta}$-2-amino pyridino propionoxy) benzene]; M. P. 145∼6$^{\circ}C$, C$\_$29/H$\_$22/N$_4$O$_4$Cl$\_$5/-were synthesized by Mannichs reaction as potential antimicrobial agents and their antimicrobial activity were tested against Bacillus subtilis, Pseudomonas ovalis, Escherichia coli, Staphylococcus aureus, aerogenes, Bacillus Acerobacter Polymyxa, Bacillus brevis, Streptomyces griseus, Candida troficalis, Rhodotorula glutinis, Candida utilis, Hansenula anamola, Saccharomyces cerevisiae in vitro. Among them, compounds of benzylamine and p-toludine showed an effective antimibrobial activity againt Bacillus subtilis and Pseudomonas ovalis.

• Journal of Soil and Groundwater Environment
• /
• v.11 no.6
• /
• pp.35-42
• /
• 2006

Experimental study was conducted to identify the active agent for reductive dechlorination of TCE in cement/Fe(II) systems. Several potential materials-hematite (${\alpha}-Fe_2O_3$), lepidocrocite (${\gamma}$-FeOOH), akaganeite (${\beta}$-FeOOH), ettringite ($Ca_6Al_2(SO_4)_3(OH)_{12}$)-that are cement components or parts of cement hydrates were tested if they could act as reducing agents by conducting TCE degradation experiments. From the initial degradation experiments, hematite was selected as a potential active agent. The pseudo-first-order degradation rate constant ($k\;=\;0.637\;day^{-1}$) for the system containing 200 mM Fe(II), hematite and CaO was close to that ($k\;=\;0.645\;day^{-1}$) obtained from the system containing cement and 200 mM Fe(II). CaO, which was originally added to simulate pH of the cement/Fe(II) system, was found to play an important role in degradation reactions. The reactivity of the hematite/CaO/Fe(II) system initially increased with increase of CaO dosage. However, the tendency declined in the higher CaO dosage region, implying a saturation type of behavior. The SEM analysis revealed that the hexagonal plane-shaped crystals were formed during the reaction with increasing degradation efficiency, which was brought about by increasing the CaO dosage. It was suspected that the crystals could be portlandite or green rust ($SO_4$) or Friedel's salt. The XRD analysis of the same sample identified the peaks of hematite, magnetite/maghemite, green rust ($SO_4$). Either instrumental analysis predicted the presence of the green rust ($SO_4$). Therefore, the green rust ($SO_4$) would potentially be a reactive agent for reductive dechlorination in cement/Fe(II) systems.

• Korean Journal of Environmental Biology
• /
• v.37 no.4
• /
• pp.749-758
• /
• 2019

The aim of this study is to provide a scientific basis for decision making regarding environmental damage in case of future chemical accidents by evaluating the ecotoxicity of 4 substances requiring preparation for accidents. For this purpose, acute and chronic toxicities of nitric acid, sulfuric acid, hydrogen peroxide, and ammonia solution, which can change the physical and chemical properties of soil to Paronychiurus kimi(Collembola) were investigated. The pH of artificial soil spiked with a series of test chemical concentrations was also measured. The pH of soil spiked with 10,000 mg kg^-1 of soil nitric acid, sulfuric acid, hydrogen peroxide, and ammonia solution were 2.86, 2.72, 7.18 and 9.69, respectively. The 28-d LC₅₀ of nitric acid, sulfuric acid, hydrogen peroxide and ammonia solution were 2,703, 5,414, 3,158 and 859 mg kg^-1 soil dry wt., respectively and 28-d EC₅₀ were 587, 2,148, 1,300 and 216 mg kg^-1 soil dry wt., respectively. These results indicated that the mortality and juvenile production of P. kimi were influenced by not only the soil pH but also by the reduced organic content and products produced by the reaction of soil with the tested chemicals. Given the fact that most substances requiring preparation for accidents can change soil characteristics, assessment and restoration methods that take into account changes in soil properties are needed for accurate decision making after chemical accidents.

• Korean Journal of Food Science and Technology
• /
• v.7 no.4
• /
• pp.229-237
• /
• 1975

An attempt was made to utilize the enzyme produced by Asp. oryzae as meat tenderizer. The production, purification, and various properties of proteinase produced by Asp. oryzae were investigated. Results obtained are as follow; 1. A strain which had the highest proteolytic activity was selected among 9 Aspergillus species. 2. Culture medium consisted of wheat bran 10g, 2% glucose, 0.03% urea and 0.1% $MgSO_4$ (pH 6.5). Mold was incubated at $30^{\circ}C$ for 3 days. 3. Enzyme extract from culture medium were fractionated with ammonium sulfate and purified by Sephadex G-75 column chromatography. 4. When pH of reaction mixture was controlled, maximal activity of proteinase by Asp. oryzae was obtained at pH 3, pH 6.6, $8.4{\sim}8.5$ and pH 10.0 to 10.5. Those results were interpreted to show that enzyme consists of acid proteinase, neutral proteinase and alkaline proteinase. Enzyme was stable at pH 6 to 10. 5. Opt. temperature for proteinase activity was $50^{\circ}C$, but enzyme was stable up to $40^{\circ}C$. 6. The proteinase was inhibited by $Ag^+$. It was also inhibited by EDTA. 7. When myofibrillar proteins were treated by proteinase from Asp. oryzae, ATPase activities of myofibrillar proteins changed remarkably. Accordingly, it was concluded that proteinase produced by Asp. oryzae were able to be used as meat tenderizer.

• Journal of Environmental Impact Assessment
• /
• v.28 no.6
• /
• pp.604-615
• /
• 2019

In this study, we produce a new type of the algae soil conditioner(ASC) using discarded algae biomass through a composting process and evaluate its nutritional characteristics. As the main ingredient, the ASCs used algae biomass collected through the coagulation-floating method and made by adding a variety of additional supporting materials (sawdust, pearlite, oilcake etc.). ASCs were divided into 0% in blank, 11.7% in ASC1, 21.6% in ASC2, 37.6% in ASC3, 59.5% in ASC4, and composted during 127 days. ASCs showed a sharp increase in temperature by aerobic microbial reaction, and 6~7 high and low temperature peaks were observed. As a result of physicochemical analysis, mineralization proceeded according to decomposing the organic matter and there was a marked increase not only in macronutrients (TN, P₂O₅, K₂O), but also in secondary macronutrients (CaO, MgO). The microbial community change was found in stage 1 (bacteria, filamentous fungi) → stage 2 (actinomycetes, bacteria) → stage 3 (Bacillus sp.), depending on the maturation process. It was estimated that microbial transition was closely related to temperature change and nutritional behavior. The quality of soil conditioner can be determined according to the maturity of compost process, and it was determined that effective microbial activity could be induced by controlling algae biomass below 59.5% in this study. In conclusion, we found out the possibility of manufacturing and utilizing soil conditioner recycled algae biomass and if further technological development is made on the basis it can be used as an effective soil conditioner.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.6
• /
• pp.279-290
• /
• 2016

The performance of upflow anaerobic bioelectrochemical reactor (UABE), equipped with electrodes (anode and cathode) inside the upflow anaerobic reactor, was compared to that of upflow anaerobic sludge blanket (UASB) reactor for the treatment of acidic distillery wastewater. The UASB was stable in pH, alkalinity and VFAs until the organic loading rate (OLR) of 4.0 g COD/L.d, but it became unstable over 4.0 g COD/L.d. As a response to the abrupt doubling in OLR, the perturbation in the state variables for the UABE was smaller, compared to the UASB, and quickly recovered. The UABE stability was better than the UASB at higher OLR of 4.0-8.0 g COD/L.d, and the UABE showed better performance in specific methane production rate (2,076mL $CH_4/L.d$), methane content in biogas (66.8%), and COD removal efficiency (82.3%) at 8.0 g COD/L.d than the UASB. The maximum methane yield in UABE was about 407mL/g $COD_r$ at 4.0 g COD/L.d, which was considerably higher than about $282mL/g\;COD_r$ in UASB. The rate limiting step for the bioelectrochemical reaction in UABE was the oxidation of organic matter on the anode surface, and the electrode reactions were considerably affected by the pH at 8.0 g COD/L.d of high OLR. The maximum energy efficiency of UABE was 99.5%, at 4.0 g COD/L.d of OLR. The UABE can be an advanced high rate anaerobic process for the treatment of acidic distillery wastewater.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.2
• /
• pp.115-123
• /
• 2013

Stoker type incinerator is one of the most popular one used as municipal solid waste (MSW) incineration because, in general, it is quite suitable for large capacity and need no preprocessing facility. Nowadays, however, since the combustible portion of incoming MSW increases together with the decrease of the moisture content due to prohibition of directly burying food waste in landfill, the heating value of waste is remarkably increasing in comparison with the early stage of incinerator installation. Consequently, the increased heating value in incinerator operation causes a number of serious problems such as reduction of waste amount to be burned due to the boiler heat capacity together with the significant NO generation in high temperature environment. Therefore, in this study, a series of numerical simulation have been made as parameters of waste amount and the fraction of moisture in air stream in order to investigate optimal operating condition for the resolution of the problems associated with the high heating value of waste mentioned above. In specific, a detailed turbulent reaction flow field calculation with NO model was made for the full scale incinerator of D city. To this end, the injection method of moisturized air as oxidizer was intensively reviewed by the addition of moisture water amount from 10% and 20%. The calculation result, in general, showed that the reduction of maximum flame temperature appears consistently due to the combined effects of the increased specific heat of combustion air and vaporization heat by the addition of water moisture. As a consequence, the generation of NOx concentration was substantially reduced. Further, for the case of 20% moisture amount stream, the afterburner region is quite appropriate in temperature range for the operation of SNCR. This suggests the SNCR facility can be considered for reoperation. which is not in service at all due to the increased heating value of MSW.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.1-2
• /
• 2011

Hybrid rockets have lately attracted attention as a strong candidate of small, low cost, safe and reliable launch vehicles. A significant topic is that the first commercially sponsored space ship, SpaceShipOne vehicle chose a hybrid rocket. The main factors for the choice were safety of operation, system cost, quick turnaround, and thrust termination. In Japan, five universities including Hokkaido University and three private companies organized "Hybrid Rocket Research Group" from 1998 to 2002. Their main purpose was to downsize the cost and scale of rocket experiments. In 2002, UNISEC (University Space Engineering Consortium) and HASTIC (Hokkaido Aerospace Science and Technology Incubation Center) took over the educational and R&D rocket activities respectively and the research group dissolved. In 2008, JAXA/ISAS and eleven universities formed "Hybrid Rocket Research Working Group" as a subcommittee of the Steering Committee for Space Engineering in ISAS. Their goal is to demonstrate technical feasibility of lowcost and high frequency launches of nano/micro satellites into sun-synchronous orbits. Hybrid rockets use a combination of solid and liquid propellants. Usually the fuel is in a solid phase. A serious problem of hybrid rockets is the low regression rate of the solid fuel. In single port hybrids the low regression rate below 1 mm/s causes large L/D exceeding a hundred and small fuel loading ratio falling below 0.3. Multi-port hybrids are a typical solution to solve this problem. However, this solution is not the mainstream in Japan. Another approach is to use high regression rate fuels. For example, a fuel regression rate of 4 mm/s decreases L/D to around 10 and increases the loading ratio to around 0.75. Liquefying fuels such as paraffins are strong candidates for high regression fuels and subject of active research in Japan too. Nakagawa et al. in Tokai University employed EVA (Ethylene Vinyl Acetate) to modify viscosity of paraffin based fuels and investigated the effect of viscosity on regression rates. Wada et al. in Akita University employed LTP (Low melting ThermoPlastic) as another candidate of liquefying fuels and demonstrated high regression rates comparable to paraffin fuels. Hori et al. in JAXA/ISAS employed glycidylazide-poly(ethylene glycol) (GAP-PEG) copolymers as high regression rate fuels and modified the combustion characteristics by changing the PEG mixing ratio. Regression rate improvement by changing internal ballistics is another stream of research. The author proposed a new fuel configuration named "CAMUI" in 1998. CAMUI comes from an abbreviation of "cascaded multistage impinging-jet" meaning the distinctive flow field. A CAMUI type fuel grain consists of several cylindrical fuel blocks with two ports in axial direction. The port alignment shifts 90 degrees with each other to make jets out of ports impinge on the upstream end face of the downstream fuel block, resulting in intense heat transfer to the fuel. Yuasa et al. in Tokyo Metropolitan University employed swirling injection method and improved regression rates more than three times higher. However, regression rate distribution along the axis is not uniform due to the decay of the swirl strength. Aso et al. in Kyushu University employed multi-swirl injection to solve this problem. Combinations of swirling injection and paraffin based fuel have been tried and some results show very high regression rates exceeding ten times of conventional one. High fuel regression rates by new fuel, new internal ballistics, or combination of them require faster fuel-oxidizer mixing to maintain combustion efficiency. Nakagawa et al. succeeded to improve combustion efficiency of a paraffin-based fuel from 77% to 96% by a baffle plate. Another effective approach some researchers are trying is to use an aft-chamber to increase residence time. Better understanding of the new flow fields is necessary to reveal basic mechanisms of regression enhancement. Yuasa et al. visualized the combustion field in a swirling injection type motor. Nakagawa et al. observed boundary layer combustion of wax-based fuels. To understand detailed flow structures in swirling flow type hybrids, Sawada et al. (Tohoku Univ.), Teramoto et al. (Univ. of Tokyo), Shimada et al. (ISAS), and Tsuboi et al. (Kyushu Inst. Tech.) are trying to simulate the flow field numerically. Main challenges are turbulent reaction, stiffness due to low Mach number flow, fuel regression model, and other non-steady phenomena. Oshima et al. in Hokkaido University simulated CAMUI type flow fields and discussed correspondence relation between regression distribution of a burning surface and the vortex structure over the surface.