• Journal of the Earthquake Engineering Society of Korea
• /
• v.16 no.3
• /
• pp.43-50
• /
• 2012

The FEMA P695 document proposed a methodology to evaluate the collapse safety of a structure and the validity of the seismic design coefficients. In this study, the seismic performance of six- and twelve-story staggered wall structures with a middle corridor was evaluated based on the FEMA P695 procedure. The analysis results of the prototype structures were compared with those of the structures with an increased coupling beam depth or an increased re-bar ratio of the coupling beams in order to investigate the effect of retrofit. The adjusted collapse margin ratios (ACMR) of the model structures obtained from incremental dynamic analyses turned out to be larger than the specified limit states of an ACMR of 20%, which implies that the analysis model structures have enough strength against design level earthquakes. It was also observed that the increase in the re-bar ratio of the coupling beams between the staggered walls was more effective in increasing the ACMR than an increase in the depth of the coupling beams.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2005.06a
• /
• pp.172-172
• /
• 2005

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.276-277
• /
• 2006

1mm-thick BLT ceramics were sintered in accordance with a bulk ceramic fabrication process. AII XRD peaks detected in the sintered ceramics were indexed as the Bi-layered perovskite structure without secondary phases. Density was increased with increasing the sintering temperature up to $1050^{\circ}C$ and the maximum value was about 98% of the theoretical density. The remanent polarization (2Pr) value of BLT ceramic sintered at $1050^{\circ}C$ was approximately $6.5\;{\mu}C/cm^2$ at the applied voltage of 4.5 kV. The calculated electromechanical coupling factor ($k_t$) of it was about 5% and the mechanical quality factor (Qm) was about 2200. From these results, a BLT ceramic target for pulsed laser deposition (PLD) system was successfully fabricated.

• Membrane Journal
• /
• v.17 no.1
• /
• pp.44-53
• /
• 2007

The primary objective of this study is to increase the extent of water flux and fouling resistance of nano-filtration or reverse osmosis membranes. This study was performed to investigate the effect of surface characteristics of silane coated membranes on modified fouling index. Commercial polyamide composite RO membrane (RE1812-LP) and NF membrane (ESNA4040-LF) were treated with silane coupling agents in ethanol at five different concentrations. The silane coupling reagent, aminopropylmethoxydiethoxysilane, contains one aminoalkyl and three alkoxy groups. The hydrophilic effect of aminoalkyl group of APMDES on the permeability and fouling resistance of the modified membrane was examined. The surfaces of the modified membranes were characterized by FE-SEM, contact angle analyzer, and zeta potentiometer in order to confirm successful sol-gel methods. The modified NF membranes showed significantly enhanced water flux and fouling resistance without a decrease in salt rejection in divalent ionic feed solution.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.4
• /
• pp.513-520
• /
• 2001

In this paper, the directional coupler using three layer microstrip substrate is proposed and the design method is notified. Modified re-entrant mode coupler is the proposed structure that one layer is added on upper plane of coupled transmission lines and the floating conductor is placed on added layer's upper planes. This structure has high coupling for the increase of odd mode capacitance and also has good performance in VSWR, isolation, phase difference because the difference of effective permittivity is small in each mode. We have designed the coupler from the calculation of impedance, effective permittivity, coupling coefficient using even, odd mode analysis method. From the simulation and measurement, proposed coupler has about 2 dB more tighter coupling than conventional coupler and also has good performance in VSWR, isolation, phase difference.

• Korean Journal of Materials Research
• /
• v.15 no.7
• /
• pp.453-457
• /
• 2005

Piezoelectric properties of $Pb(Mn_{1/3}Nb_{2/3})O_3-PbZrO_3-PbTiO_3$ ceramics were investigated with $Al_2O_3$ content $(0.0-1.0 wt\%)$. The constituent phases, microstructure, electromechanical coupling factor, dielectric constant, piezoelectric charge and voltage constants were analyzed. Diffraction peaks for (002) and (200) planes were identified by X-ray diffractometer for all the specimens doped with $Al_2O_3$, indicating the MPB (morphotropic phase boundary) composition of tetragonal structures. The highest sintered density of $7.8 g/cm^3$ was obtained for $0.2wt\%\;Al_2O_3-doped$ specimen. Grain size increased by doping $Al_2O_3$ up to $0.3 wt\%$, and it decreased by more doping. Electromechanical coupling factor, dielectric constant, piezoelectric charge and voltage constants increased by doping $Al_2O_3$ up to $0.2wt\%$, and it decreased by more doping. This might result from the formation of oxygen vacancies due to defects in $O^{2-}$ ion sites and the substitution of $Al^{3+}$ ions.

• Journal of the Korean Society for information Management
• /
• v.25 no.1
• /
• pp.173-190
• /
• 2008

Author co-citation analysis(ACA) technique has been widely used for identifying research areas and trends in a discipline. But this technique has some limitations, mainly due to citation delay, on analyzing current trends and identifying active researchers. In this study, a new method, named as Bibliographic Author Coupling Analysis (BACA), is suggested for overcoming those limitations of author co-citation analysis. BACA is based on Kessler's bibliographic coupling approach and focuses not on documents but on authors. Simply stated, BACA technique assumes that those likewise citing authors have the same research interests. For the purpose of comparing with author co-citation analysis, two preceding studies with author co-citation analysis are reconsidered and re-examined using BACA. The comparing results can be regarded as promising the usefulness of BACA in analyzing current research trends and identifying active researchers.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.3
• /
• pp.335-340
• /
• 2011

Building energy saving is one of the most important issues in these days. Control algorithm for energy saving should be designed properly to reduce power consumption in building. Recently, building energy system consists of hybrid energy system coupling with RE (Renewable Energy) source. In this paper, an optimum control algorithm for building energy saving is applied to BEMS (Building Energy Management System) by using an outdoor air temperature prediction strategy. BEMS coupling with renewable energy can control HVAC (Heating, Ventilating and Air-Conditioning) system effectively. In order to verify the effectiveness of building energy saving, BEMS was tested for several months at a laboratorial chamber with an air conditioner, fan and heater. To this end BEMS embedded control algorithm has been tested successfully.

• Journal of the Optical Society of Korea
• /
• v.5 no.4
• /
• pp.131-135
• /
• 2001

We report experiemtnal results demonstrating the electromagnetically induced transparency (EIT) in trapped Cs atoms. EIT occurs at the Λ-type configuration where the re0-pumping laser simultaneously plays a role as the coupling laser in the presence of a magneto-optical trapping and weak magnetic fields. Dependences of EIT signal on both the intensity and the detuning of the coupling laser were investigated. Linear absorption spectra for cold cesium atoms in the magneto-optical trap have been observed and shown the pronounced dispersion-like structure with sub-natural linewidth of 1 MHz due to the cooling laser.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.275-283
• /
• 1999

To predict the dynamic behavior of the cylindrical liquid storage tank subjected to seismic ground motion three dimesional analysis with liquid-structure interaction must be performed, In this study a three dimensional dynamic analysis method over the frequency domain using FE-BE coupling technique which combines the efficiency of the boundary elements for liquid with the versatility of the finite shell elements for tank. The liquid region is modeled using boundary elements which can counter the sloshing effect at free surface and the structure region the tank itself is modeled using the degenerated finite shell elements. At the beginning of the procedure the equivalent mass matrix of the liquid is generated by boundary elements procedure. Then this equivalent mass matrix is combined with the mass matrix of the structure to produce the global mass matrix in the equation of the motion of fluid-structure interaction problem In order to demonstrate the accuracy and validity of the developed method the numerical results re compared with the previous studies. Finally the effects of the fluid-structure interaction on the natural frequency and dynamic response of the system are analyzed.