• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.27-33
• /
• 1998

The powertrain is a system of exciters which are connected by vibration transmitters and noise radiators. The powertrain has infinite natural frequencies. If the engine explosion, excites a certain natural frequency, then the powertrain system seriously vibrates. The torsional vibration arises from here. Torsional vibration like this can cause various noises as rattle and booming. In this study, the simulation models of multiple degrees of freedom were developed to reduce the torsional vibration of the powertrain. These models are combined mass moment of inertias with torsional springs. The free and forced vibration analyses were carried out by these models; and the validity of the simulation models were checked by the field test. The reduction effect of the torsional vibration along the driveline design factor is presented by the analytical results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.217-224
• /
• 1994

변속기에서 발생하는 치타음을 클러치를 통하여 해결하려는 방법으로 자동차 중립시와 주행시 각기 다른 비틀림특성을 갖는 클러치를 대상으로 한 실험으로부터 엔진플라이휠, 인풋기어, 변속기 케이스의 진동을 측정하고 분석함으로써 다음과 같은 결론을 얻었다. 자동차 중립시나 주행시에 수동변속기에서 발생하는 치타음은 클러치를 통하여 해결될 수 있음을 알 수 있었다. 클러치의 프리댐퍼와 메인댐퍼의 비틀림강성과 히스테리시스는 중립시와 주행시 치타음에 대해 각기 다른 특성을 갖게 되는데 메인 댐퍼만으로 구성된 클러치는 주행시에는 치타음을 제거하는데 효과적이지만 중립시에는 인풋기어의 비틀림 공진에 의하여 변속기가 가진되어 치타음이 발생하였다. 주행시 변속기 치타음 제거효과를 감소시키지 않고 중립시 변속기에서 발생하는 치타음을 제거하기 위해 메인댐퍼만으로 이루어진 클러치디스크에 프리댐퍼 부분을 첨가하여 보았는데 자동차 주행시의 치타음 제거효과를 유지하면서 중립시의 치타음을 제거시킬 수 있다는 것을 확인하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.791-795
• /
• 2014

In this paper, in order to impart the aging condition of the parts, by configuring the cycle of temperature from low temperature was performed by applying the aging conditions for vehicle cockpit module. The reason for the selected modules of the cockpit vehicle parts, because the joint occurrence typical components of the room component is a first module and ceiling cockpit module. After setting the excitation profile using the BSR exciter only that this is for the module degradation after the initial and grasp the change in the dynamic characteristics of the modules based on the before and after deterioration may be made in the module, grasp the noise generating position I measured the noise and proximity. Was also visualized on the position of the joint is generated using a sound camera to objective results occurring where the joint is selected through subjective evaluation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.171-176
• /
• 2008

Active suspension controls stiffness and damping between unsprung mass and sprung mass in order to increase the ride quality. However, to increase the riding quality, the handling quality should be decreased and the rattle space should be increased. So, active suspension should cope with these conflict conditions. Therefore its actuating devices have to produce sufficient actuating force and have sufficiently short response time. In this paper, the dynamic characteristics of 1/4 car model with an active suspension is studied according to hydraulic design variables. The active suspension consists of a hydraulic servo valve and a hydraulic cylinder. It shows better performance when it has more powerful and faster actuator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.909-917
• /
• 2007

Recently the trend of automobile industry is that IQS evaluation index against a sensitivity quality is increasing. To reduce rattle noise due to speaker sound at low frequencies, it is required the advanced investigation of a package tray panel and a door module panel. This paper optimized the design parameters of package tray panel according to the theoretical background about robust design and suggested the design guideline for resonance avoidance and the reduction of vibrational sensitivity considering the excitation frequency of woofer speaker. In addition, it is suggested the design guideline of a door module panel through the sensitivity analysis in case of the speaker excitation. Finally, the design factor analysis of the quality deviation of a mother-car will make it possible to guarantee the stable characteristics of vehicle vibration in the early stage of vehicle development. These improvements can lead to shortening the time needed to develop better vehicles.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.8
• /
• pp.673-682
• /
• 2007

Recently the trend of automobile industry is that IQS evaluation index against a sensitivity quality is increasing. To reduce rattle noise due to speaker sound at low frequencies, it is required the advanced technology analysis process of body structure. This paper optimized the design parameters of package tray panel according to the theoretical background about robust design and suggested the design guideline for resonance avoidance and the reduction of vibrational sensitivity considering the excitation frequency of woofer speaker. And this paper described the design process of a door module panel through the sensitivity analysis in case of the door speaker excitation. Finally, the analysis of the quality deviation using mother car is suggested to guarantee the stable characteristics of vehicle vibration in the early stage of vehicle development. These improvements can lead to shortening the time needed to develop better vehicles.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.4776-4783
• /
• 2014

Many studies have examined the reduction of primary noise sources, but quality-related noise, such as BSR, is rarely studied. This study describes the quantitative BSR test method using a multi-axial simulator. The sine sweep test was conducted to detect the system resonance and its relation to BSR noise with high frequency. This method is applied to the seat frame with/without the vibration durability test. The results showed that the $1^{st}$ lateral resonance leads to higher BSR frequency noise. In addition, the reduction of the lateral mode system stiffness after the durability test results in a decrease in the BSR noise in sine sweep test mode.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3246-3252
• /
• 1994

The vibration of meshing gear system is originated form teeth deformation, teeth contact ratio, profile error, etc. The gear vibration is classified as whine vibration during meshing and as rattle vibration during idling. In this study, the whine vibration is investigated under the assumption of piecewise linearity of elastic stiffness due to the variation of meshing. Numerical, theoretical and experimental investigations show the existence of the superharmonic components of the second and the third order. consistently It can be concluded that the superharmonic components in whine vibration of meshing gear is originated from the stiffness variation. It also shows that the higher order harmonics are reduced on the increase of motor speed.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.132-140
• /
• 1996

This paper developes a torsional vibration model of heavy duty truck drive line for simulation of a driving rattle, which causes very annoying noise to driver at the full load driving condition. Test results show a peak in the fit plots at the frequency of the 2nd harmonics of propeller shaft revolution. A 10 d.o.f. lumped parameter nonlinear torsional vibration model is constructed and engine torque variation is calculated from P- .theta. diagram. Time responses are simulated and compared with the test results, which show fairly good agreement. The effects of paramenter change are investigated, and the optimum configuration is proposed.

• Composites Research
• /
• v.34 no.3
• /
• pp.192-198
• /
• 2021

Due to enormous market growing of electric vehicles without combustion engine, reducing unwanted BSR (buzz, squeak, and rattle) noise is highly demanded for vehicle quality and performance. Particularly, innerbelt weatherstrips which not only block wind noise, rain, and dust from outside, but also reduce noise and vibration of door glass and vehicle are required to exhibit high damping properties for improved BSR performance of the vehicle. Thermoplastic elastomers (TPEs), which can be recycled and have lighter weight than thermoset elastomers, are receiving much attention for weatherstrip material, but TPEs exhibit low material damping and compression set causing frictional noise and vibration between the door glass and the weatherstrip. In this study, high damping EPDM (ethylene-propylene-diene monomer)/PP (polypropylene) thermoplastic vulcanizates (TPV) were investigated by varying EPDM/PP ratio and ENB (ethylidene norbornene) fraction in EPDM. Viscoelastic properties of TPV materials were characterized by assuming that the material damping is directly related to the viscoelasticity. The optimum material damping factor (tanδ peak 0.611) was achieved with low PP ratio (14 wt%) and high ENB fraction (8.9 wt%), which was increased by 140% compared to the reference (tanδ 0.254). The improved damping is believed due to high fraction of flexible EPDM chains and higher interfacial slippage area of EPDM particles generated by increasing ENB fraction in EPDM. The stick-slip test was conducted to characterize frictional noise and vibration of the TPV weatherstrip. With improved TPV material damping, the acceleration peak of frictional vibration decreased by about 57.9%. This finding can not only improve BSR performance of electric vehicles by designing material damping of weatherstrips but also contribute to various structural applications such as urban air mobility or aircrafts, which require lightweight and high damping properties.