• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.1
• /
• pp.57-70
• /
• 2009

Considerable advance has been made on research on effect of steel pipe Umbrella Arch Method (UAM) and mechanical reinforcement mechanism through numerical analyses and experiments. Due to long analysis time of three-dimensional analysis and its complexity, un-quantitative two-dimensional analysis is dominantly used in the design and application, where equivalent material properties of UAM reinforced area and ground are used, For this reason, development of reasonable, theoretical, quantitative and easy to use design and analysis method is required. In this study, both field UAM tests and laboratory tests were performed in the residual soil to highly weathered rock; field tests to observe the range of reinforcement, and laboratory tests to investigate the change of material properties between prior to and after UAM reinforcement. It has been observed that the increase in material property of neighboring ground is negligible, and that only stiffness of steel pipe and cement column formed inside the steel pipe and the gap between steel pipe and borehole contributes to ground reinforcement. Based on these results and concept of Convergence Confinement Method (CCM), two dimensional axisymmetric analyses have been performed to obtain the longitudinal displacement profile (LDP) corresponding to arching effect of tunnel face, UAM effect and effect of supports. In addition, modified load distribution method in two dimensional plane-strain analysis has been suggested, in which effect of UAM is transformed to internal pressure and modified load distribution ratios are suggested. Comparison between the modified method and conventional method shows that larger displacement occur in the conventional method than that in the modified method although it may be different depending on ground condition, depth and size of tunnel, types of steel pipe and initial stress state. Consequently, it can be concluded that the effect of UAM as a beam in a longitudinal direction is not considered properly in the conventional method.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.43 no.4
• /
• pp.216-224
• /
• 2023

Since maize (Zea mays L.) originated in central and south America, it requires warm climate conditions throughout its growing season. Growth halts when night-time temperatures drop below 10℃, and the plant may die if temperature reach -1.7℃. Thus, temperature should be maintained between 10 and 30℃ from seeding to maturity. The germination temperature for maize should be at least 8-11℃, whit an optimal range 32-34℃. Since temperature significantly affects the germination rate and period, it plays a crucial role in maize growth. In this study, we evaluated the quantity and feed value of 11 major varieties to determine those best suited for maize cultivation as feed in higher latitude, specifically in Democratic People's of Republic of Korea, below 38 degrees north. A cultivation test was also conducted in Suwon in Republic of Korea, to assess adaptability in areas south of Mt. Suyang. Among the varieties tested, Shinhwangok2 reached silking the fastest, in 65 days, while Gwangpyeongok took the longest at 75 days. The stem length of all varieties exceeded 230 cm. Gwangpyeongok had the tallest stems, while Daanok and Shinhwangok2ho displayed the highest ear ratios. Dacheongok presented the highest values in both dry matter and TDN quantity, with 31,420 kg/ha and 21,66 kg/ha respectively. Pyeonggangok had the highest crude protein content at 8.0%. TDN (%) ranged from 57-68%, with Hwangdaok reaching up to 68%. Based on these findings, Dacheongok and Pyeonggangok appear to be the most suitable varieties for cultivation in terms of both quantity and feed value.

• Korean Journal of Ecology and Environment
• /
• v.56 no.4
• /
• pp.281-302
• /
• 2023

Carbon is not only an essential element for life but also a key player in climate change. The radiocarbon (¹⁴C) analysis using accelerator mass spectrometry (AMS) is a powerful tool not only to understand the carbon cycle but also to track pollutants derived from fossil carbon, which have a distinct radiocarbon isotope ratio (Δ¹⁴C). Many studies have reported Δ¹⁴C of carbon compounds in streams, rivers, rain, snow, throughfall, fine particulate matter (PM_2.5), and wastewater treatment plant effluents in South Korea, which are reviewed in this manuscript. In summary, (1) stream and river carbon in South Korea are largely derived from the chemical weathering of soils and rocks, and organic compounds in plants and soils, strongly influenced by precipitation, wastewater treatment effluents, agricultural land use, soil water, and groundwater. (2) Unprecedentedly high Δ¹⁴C of precipitation during winter has been reported, which can directly and indirectly influence stream and river carbon. Although we cannot exclude the possibility of local contamination sources of high Δ¹⁴C, the results suggest that stream dissolved organic carbon could be older than previously thought, warranting future studies. (3) The ¹⁴C analysis has also been applied to quantify the sources of forest throughfall and PM_2.5, providing new insights. The ¹⁴C data on a variety of ecosystems will be valuable not only to track the pollutants derived from fossil carbon but also to improve our understanding of climate change and provide solutions.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.3
• /
• pp.22-44
• /
• 2023

The subsistence economics of the early Bronze Age has focused on explaining the intensity of agricultural practices without sufficiently taking into account the diversity of production methods that may arise from cultural types or environmental factors. The problem appears to stem from paying insufficient attention to the question whether we should understand the transition from the Neolithic Age to the Bronze Age as continuous or discrete. This has hitherto blocked an avenue to investigate the gradual changes in subsistence resource production methods. Taking as its premise that changes in the production methods of subsistence resources in the Bronze Age have been continuous and gradual, this paper seeks to restore the production patterns of subsistence resources according to the variety of factors that may have influenced the early Bronze Age production method. With diverse cultural patterns and ecological spaces of the early Bronze Age being confirmed, the work of restoring the production methods of subsistence resources in a specific period is difficult to achieve with one or two stand-alone analyses. A more appropriate method would involve separating a number of different aspects related to the production of subsistence resources, analyzing and interpreting each, and in the final stage, synthesizing the analyses. The specific research method employed in this paper checked for compositional differences in stone production tools, functionally categorized according to a variety of factors that have a close relationship with the production of subsistence resources: cultural-environmental factors and cultural patterns, geographical and topographical factors, soil productivity, and size of settlement. The results of the analysis are as follows: for the early Bronze Age production pattern of subsistence resources in the Seoul and Gyeonggi regions, while no substantive differences were observed with respect to cultural type, geographical and topographical location, the results show statistically significant differences in the composition of production tools according to settlement size and soil productivity. Also, with an increasing ratio of settlement size and total production soil, increases in hunting and armoring tools, woodworking tools, and harvesting tools were observed; on the other hand, when it came to the ratio of fishing tools, the opposite relationship was observed. While a correlation between settlement size or crop cultivation productivity and dependence on hunting or farming was expected, the results of the regression analysis show that settlement size and soil productivity ratios do not have mutually significant relationships. The results thus illustrate that patterns of production differ according to a variety of factors, and no single factor is decisive in the adoption of subsistence resource production methods by a specific settlement. Therefore, the paper emphasizes the need to investigate the production patterns of subsistence resources according to the variety of cultural and environmental factors that make up settlements in early Bronze Age society.

• Korean Journal of Plant Resources
• /
• v.36 no.5
• /
• pp.517-526
• /
• 2023

The harvest time of the late-ripening 'Fuji' apple (Malus × domestica) is variable, depending on the coloration of the fruit skin. Ethephon, a plant growth regulator, promotes the ethylene production and induces physiological responses associated with fruit maturation in climacteric fruit crops, such as apples. This study aimed to investigate the effect of ethephon treatment on fruit characteristics after fruit enlargement, with the objective of proposing an economical and stable harvest control method for 'Fuji'/M.26 apples. Fruit characteristics were assessed at 10-days intervals following the application of 100 mg/L ethephon and mixture of 100 mg/L ethephon and 0.5% CaCl₂ at 145 days after full bloom (DAFB). Starch contents of ethephon-treated (ET) and ethephon with CaCl₂-treated (EC) apples began to decrease from 155 DAFB, and the starch contents of ET and EC at 10 days before harvest were similar to those of control at harvest time. Red coloration of fruit skin in EC was lower compared to ET but higher than control. The average fruit firmness was low in ET, while the control and EC exhibited similar levels of firmness. Fruit sugar acid ratios did not show significant differences between treatments. However, the titratable acidity of EC was significantly lower than that of the control at 10 days before harvest. Moreover, fruit sugar acid ratio of ET and EC at 10 days before harvest in 2021 was similar to their sugar acid ratio at harvest time. Therefore, it was thought that fruit maturation and skin coloration could be accelerated by 10 days from the harvest time through the combined treatment of 100 mg/L ethephon and 0.5% CaCl₂ at the end of fruit enlargement in 'Fuji'/M.26.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.52-58
• /
• 2023

With the increasing awareness of the importance of carbon neutrality in response to global climate change, the utilization of hydrogen as a carbon-free fuel source is also growing. Hydrogen is commonly used in fuel cells (FC), but it can also be utilized in internal combustion engines (ICE) that are based on combustion. Particularly, ICEs that already have established infrastructure for production and supply can greatly contribute to the expansion of hydrogen energy utilization when it becomes difficult to rely solely on fuel cells or expand their infrastructure. However, a disadvantage of utilizing hydrogen through combustion is the potential generation of nitrogen oxides (NOx), which are harmful emissions formed when nitrogen in the air reacts with oxygen at high temperatures. In particular, for the EURO-7 exhaust regulation, which includes cold start operation, efforts to reduce exhaust emissions during the warm-up process are required. Therefore, in this study, the characteristics of nitrogen oxides and fuel consumption were investigated during the warm-up process of cooling water from room temperature to 88℃ using a 2-liter direct injection spark ignition (SI) engine fueled with hydrogen. One advantage of hydrogen, compared to conventional fuels like gasoline, natural gas, and liquefied petroleum gas (LPG), is its wide flammable range, which allows for sparser control of the excessive air ratio. In this study, the excessive air ratio was varied as 1.6/1.8/2.0 during the warm-up process, and the results were analyzed. The experimental results show that as the excessive air ratio becomes sparser during warm-up, the emission of nitrogen oxides per unit time decreases, and the thermal efficiency relatively increases. However, as the time required to reach the final temperature becomes longer, the cumulative emissions and fuel consumption may worsen.

• Korean Journal of Poultry Science
• /
• v.51 no.1
• /
• pp.11-19
• /
• 2024

This study was conducted to evaluate the potential of using laying hens as meat type chickens. Male broiler (Ross 308, R3), laying hens (Hy-Line Brown, HL), and Korean native chickens (Hanhyup-3, H3) were used, and 100 heads of each were prepared. Carcass characteristics, meat quality, and sensory quality characteristics were compared as analysis items. The rearing environment and feed for all treatments were identical to the broiler rearing manual, and the lighting system was maintained at 23L:1D. Feed and water were provided ad libitum. The test ended when the average weight of each treatment group reached 1.5 kg, and individuals of similar weight were randomly selected and compared. As a result of this study, the live weight of the selected individuals was approximately 1.5 kg, which was similar for all treatments (P>0.05). However, carcass weight and ratio and breast meat production were highest in R3, while HL had higher ratios of legs, wings, and neck (P<0.05). The H3 group showed high pH and WHC levels and low cooking loss, and R3 improved chicken meat color (P<0.05). In particular, the fat content in meat was lowest in HL (P<0.01). Nucleic acid substances ATP, Hx, ADP, AMP, and INO were abundant in R3, and IMP content was highest in HL (P<0.05). In sensory evaluation, all treatments showed similar characteristics and overall preferences (P>0.05). Based on the findings, it appears that HL, a male laying hen, produces meat with unique characteristics such as low fat content and high IMP content.

• Food Science and Preservation
• /
• v.31 no.2
• /
• pp.315-323
• /
• 2024

This study aims to confirm the anti-inflammatory activities of acemannan and aloesin, which have been studied for various efficacies at various mixed sample ratios. The mixed samples were mixed at a ratio of 1:1 (AA-1), 1:2 (AA-2), 1:3 (AA-3), 2:1 (AA-4), and 3:1 (AA-5). Seven samples were evaluated for their cytotoxic ability on macrophages, and the results showed that all cell viability was over 90% at a concentration of 100 ㎍/mL. First, due to the NO production inhibitory activity, a better inhibitory effect was achieved when using a mixed sample rather than a single material. Afterward, the activity of inhibiting the production of PGE₂, TNF-α, and IL-6 was confirmed using a mixed sample. It was confirmed that AA-2 had the best inhibitory activity on producing PGE2, TNF-α, and IL-6 rather than AA-1, AA-3, AA-4, and AA-5. For this reason, experiments were conducted using AA-2 to determine the protein expression levels of iNOS and COX-2, which are inflammation-related proteins. It was confirmed that AA-2 inhibited iNOS and COX-2 protein expression by 25.01% and 27.27%, respectively, compared to the LPS-alone treatment group. In conclusion, the mixed sample of acemannan and aloesin is judged to have anti-inflammatory activity and can potentially to be used as a functional material.

• Journal of Wetlands Research
• /
• v.26 no.2
• /
• pp.168-181
• /
• 2024

Constructed wetlands (CWs) deliver a range of ecosystem services, including the removal of contaminants, sequestration and storage of carbon, and enhancement of biodiversity. These services are facilitated through hydrological and ecological processes such as infiltration, adsorption, water retention, and evapotranspiration by plants and microorganisms. This study investigated the correlations between microbial populations, soil physicochemical properties, and treatment efficiency in a horizontal subsurface flow constructed wetland (HSSF CW) treating runoff from roads and parking lots. The methods employed included storm event monitoring, water quality analysis, soil sampling, soil quality parameter analysis, and microbial analysis. The facility achieved its highest pollutant removal efficiencies during the warm season (>15℃), with rates ranging from 33% to 74% for TSS, COD, TN, TP, and specific heavy metals including Fe, Zn, and Cd. Meanwhile, the highest removal efficiency was 35% for TOC during the cold season (≤15℃). These high removal rates can be attributed to sedimentation, adsorption, precipitation, plant uptake, and microbial transformations within the CW. Soil analysis revealed that the soil from HSSF CW had a soil organic carbon content 3.3 times higher than that of soil collected from a nearby landscape. Stoichiometric ratios of carbon (C), nitrogen (N), and phosphorus (P) in the inflow and outflow were recorded as C:N:P of 120:1.5:1 and 135.2:0.4:1, respectively, indicating an extremely low proportion of N and P compared to C, which may challenge microbial remediation efficiency. Additionally, microbial analyses indicated that the warm season was more conducive to microorganism growth, with higher abundance, richness, diversity, homogeneity, and evenness of the microbial community, as manifested in the biodiversity indices, compared to the cold season. Pollutants in stormwater runoff entering the HSSF CW fostered microbial growth, particularly for dominant phyla such as Proteobacteria, Actinobacteria, Acidobacteria, and Bacteroidetes, which have shown moderate to strong correlations with specific soil properties and changes in influent-effluent concentrations of water quality parameters.

• The Journal of Korean Academy of Prosthodontics
• /
• v.62 no.2
• /
• pp.95-103
• /
• 2024

Purpose. With the advancement of digital technology, 3D printing is being utilized in the fabrication of denture base. Nevertheless, increasing microbial adhesion to the surface of denture base has been reported as the disadvantage of 3D-printed denture base. The purpose of this study is to investigate the antifungal properties and flexural strength of 3D-printed denture base resin according to the different contents of titanium dioxide nanoparticles. Materials and methods. Titanium dioxide nanoparticles were mixed with the 3D printing resin at the ratios of 0.5, 1, 1.5, and 2 wt%. Twenty specimens per each group were printed in the form of cylindrical shape (diameter: 20 mm, height: 3 mm) to evaluate antifungal properties. Ten specimens from each group underwent polishing using autogrinder, while the remaining ten specimens did not. Candida albicans in hyphae form was inoculated onto each specimen, optical density and colony-forming unit were analyzed. The surface of the specimen was observed using scanning electron microscopy. To evaluate the flexural strength, twenty specimens per each group were 3D printed in the form of rectangular prism shape (length: 64 mm, height: 10 mm, width: 3 mm) and three-point bending tests were conducted using universal testing machine according to ISO 20795-1. Results. Colony-forming unit of C.albicans and optical density of culture medium showed no difference between non-polished groups, but decreased in the polished groups at concentration of 1, 1.5, 2 wt% titanium dioxide nanoparticles. Flexural strength increased with titanium dioxide nanoparticle at concentration of 0.5, 1, 1.5 wt%, but decreased at 2 wt% compared to 1.5 wt%. Conclusion. When 1.5 wt% of titanium dioxide nanoparticles were added to the 3D-printed denture base resin with polishing, antifungal properties were increased.