• 한국산학기술학회논문지
• /
• 제21권2호
• /
• pp.588-594
• /
• 2020

이 연구에서는 철근콘크리트 건축물의 슬래브에 대해 화재 후 잔존 구조성능을 상온 시 내구성 진단과는 다르게, 고온특성을 보다 정확히 평가하기 위하여 전기로를 이용 800 ℃까지의 가열실험을 수행하였고 가열 전 후의 잔존 구조성능을 반발경도법과 초음파속도법 등의 비파괴 검사와 아울러 진동실험으로 구한 고유진동수로 처짐계산에 사용되는 강성을 평가하는 기법을 제안하였다. 반발경도를 이용한 압축강도 평가에서는 두꺼운 두께와 물/시멘트비(W/C)가 큰 실험체의 잔존 압축강도가 크게 나타났다. 콘크리트를 투과하는 초음파속도로 상온 대비 고온수열 콘크리트의 균질도를 평가하였으며 W/C와 부재 두께의 차이는 초음파 속도법의 결과에 큰 차이가 없는 것으로 판단되었다. 화재 피해 슬래브의 처짐 증가에 영향을 미치는 강성을 평가하기 위한 기법으로, 진동실험에 의해 고유진동수를 측정하고 이를 강성과의 관계식에 대입하였으며, 이를 슬래브 실험체에 적용해 본 결과 매우 합리적인 평가기법이 될 수 있음을 보여주었다. 또한, 고온 수열 후 부재의 잔존강도를 평가하기 위해 가열중과 가열 후 가력실험을 수행한 결과 800 ℃ 내력은 상온의 부재 내력에 비해 22%의 감소를 나타내었다.

• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.357-366
• /
• 1992

Residual organics were considered as impurity in Sol-Gel method. The purpose of this study was to find the conditions to contain as much residual organics as possible in silica gel prepared from TEOS(tetraethylortho-silicate) by Sol-Gel method. Residual organics are to be expected to have reduction effect on synthesizing Si3N4 from silica gel. The results of this study are follows: 1) The maximum content of entrapped carbon was 19.8 wt.%(C/SiO2=0.25 wt.ratio) in silica gel synthesized under the conditions 1.5 fold mole water for incomplete hydrolysis, 2.5 fold mole phenol as a solvent and 0.1 fold mole HCl as a catalyst to TEOS. 2) Silica gel with organics entrapped by Sol-Gel method had a positive effect on the formation of Si3N4 compared with commercial silica gel. 3) Sintered body of synthesized $\alpha$-Si3N4 with Y2O3 and Al2O3 as additives at 175$0^{\circ}C$ in N2 atmosphere showed bending strength, 602$\pm$20 MPa and frature toughness 4.45$\pm$0.15 MPa.m1/2.

• Journal of Welding and Joining
• /
• 제15권5호
• /
• pp.104-114
• /
• 1997

The microstructure and bond strength were investigated on the SiC/SiC and SiC/mild steel joints brazed by Ag-5at%Ti alloy. Ag-5at%Ti-2at%Fe and -5at%Fe brazing alloys were also used to see the effects of Fe addition on the bond strength of SiC/SiC brazed joints. Brazing temperature and brazing gap were selected and examined as brazing variables. The microstructure of SiC/SiC brazed joints was affected by Fe addition to the Ag-5at%Ti alloy, but the bond strength was not. Increasing brazing temperature also changed the microstructure of $Ti_5Si_3$ reaction layer and brazing alloy matrix of the SiC/SiC and SiC/mild steel joints, but not the bond strength. Brazing gap had a great effects on the bond strength. Decreasing brazing gap from 0.2 mm to 0.1 mm in SiC/SiC brazing increased the bond strength from 187 MPa to 263 MPa and, in SiC/mild steel brazing, from 189 MPa to 212 MPa. It was concluded that the most important parameter on the bond strength in SiC/SiC and SiC/mild steel brazing was the relative ratio between brazing gap and specimen size.

• 콘크리트학회논문집
• /
• 제18권1호
• /
• pp.3-12
• /
• 2006

화해를 입은 콘크리트 구조물의 거동은 많은 변수에 따라 영향을 받는 복잡한 현상을 나타낸다. 연구에서 고려되는 변수들은 콘크리트 및 철근이 받는 온도크기 및 가열시간, 콘크리트와 철근의 기계적 물성, 함수율, 피복두께, 편심유무, 기둥단면형상 등을 들 수 있다. 이러한 주요변수들이 화해를 입은 기둥의 잔존내력에 미치는 영향을 추적할 수 있는 수치해석 모델이 존재하나 실무에서 용이하게, 그러나 어느 정도 정확성을 갖고 화해 입은 기둥의 잔존내력을 예측할 수 있는 실용예측식이 필요하다. 본 연구에서는 이 목적을 위하여 화해를 입은 보통강도 철근콘크리트 정방형 기둥에 대하여 수치해석적 모델에 의한 잔존내력 예측치를 근사적으로 산정할 수 있는 실용예측식을 개발하였다. 개발된 식은 화해시간, 콘크리트강도, 철근비, 기둥단면크기의 영향을 고려한다. 개발된 실용예측식에 의한 잔존내력값은 수치해석 모델에 의한 잔존내력값을 비교적 근접하게 예측하였다. 화해를 입은 보통강도 철근콘크리트 기둥에 대한 잔존내력, 안정성 및 추가 필요내력의 산정 등에 대한 예제를 수록하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.157-167
• /
• 2002

In most cases, quantity of reinforcement is determined without regard to the difference of initial strain, and status of damages when calculated the strengthening in flexure at beams. Thus, the purpose of this study is to investigate the flexural strengthening efficiency and behavior of RC beams strengthened with carbon fiber sheets(CFS) considering different status of damages. in this paper, a nonlinear analysis program considering rip-off strength and residual stress of steel bars and concrete in different status of damages is developed to predict the flexural behavior of CFS strengthened beams. Rip-off strength equation is obtained by modifying moment of inertia in the Robert's equation. And conformed developed nonlinear analysis program in variable of strengthening CFS amount and status of damages(initial, case1, case2, case3) and tension reinforcement ratio(0.2~1.0%).

• The Korean Journal of Ceramics
• /
• 제1권1호
• /
• pp.45-54
• /
• 1995

Four kinds of silicon nitride based ceramic materials have been hot pressed. Effect of the sintering additives on the phase transformation, microstructural development and mechanical properties was investigated. While sintering under the same condition a big difference among the microstructures of the specimens, they appeared alike if sintered to have a similiar $\alpha$-$\beta$ phase ratio. The specimen of the stoichiometric $\alpha$-$\beta$ sialon composition showed very limited amount of the intergranular glassy phase and a significant degree of the residual stress. It exhibited almost no strength degradation up to $1300^{\circ}C$, and the strength of the specimen degraded more as its composition deviated from the stoichiometry.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.467-482
• /
• 2020

This research focused on analyzing the post-fire behavior of high-performance concrete-filled steel tube (CFST) columns, with the concrete containing tire rubber and steel fibers, under axial compressive loading. The finite element (FE) modeling of such heated columns containing recycled aggregate is a branch of this field which has not received the proper attention of researchers. Better understanding the post-fire behavior of these columns by measuring their residual strength and deformation is critical for achieving the minimum repair level required for structures damaged in the fire. Therefore, to develop this model, 19 groups of confined and unconfined specimens with the variables including the volume ratio of steel fibers, tire rubber content, diameter-to-thickness (D/t) ratio of the steel tube, and exposure temperature were considered. The ABAQUS software was employed to model the tested specimens so that the accurate behavior of the FE-modeled specimens could be examined under test conditions. To achieve desirable results for the modeling of the specimens, in addition to the novel procedure described in this research, the modified versions of models presented by previous researchers were also utilized. After the completion of modeling, the load-axial strain and load-lateral strain relationships, ultimate strength, and failure mode of the modeled CFST specimens were evaluated against the test data, through which the satisfactory accuracy of this modeling procedure was established. Afterward, using a parametric study, the effect of factors such as the concrete core strength at different temperatures and the D/t ratio on the behavior of the CFST columns was explored. Finally, the compressive strength values obtained from the FE model were compared with the corresponding values predicted by various codes, the results of which indicated that most codes were conservative in terms of these predictions.

• 한국터널지하공간학회 논문집
• /
• 제12권1호
• /
• pp.51-60
• /
• 2010

최근 새로운 형태의 폴리올레핀 섬유에 대하여 성능향상 개발이 이루어지고 있으며, 기존 섬유와 혼입하여 사용하거나 폴리올레핀 섬유만을 사용한 콘크리트 특성에 대하여 연구와 검증이 필요하다. 본 연구의 목적은 강섬유와 폴리올레핀 섬유를 사용한 콘크리트의 휨 인성 및 휨 인장강도에 대한 성능을 확인하기 위하여 324개의 보 시편을 제작하고, KS F2566과 ASTM C 1399-02규격에서 제시한 4점 휨 실험을 수행하여 휨 인성지수, 등가 휨 인장강도, 평균잔류강도를 분석하였다. 실험결과, 섬유 혼입률, 섬유 형상비에 대한 휨 인성 및 인장강도에 대한 효과가 확인되었으며, 강섬유와 폴리올레핀의 최적의 혼입비율을 제시하였다.

• Structural Engineering and Mechanics
• /
• 제87권2호
• /
• pp.151-164
• /
• 2023

The latest earthquake's costly repairs and economic disruption were brought on by excessive residual drift. Self-centering systems are one of the most efficient ways in the current generation of seismic resistance system to get rid of and reduce residual drift. The mechanics and behavior of the self-centering system in response to seismic forces were impacted by a number of important factors. The amount of post-tensioning (PT) force, which is often employed for the standing posture after an earthquake, is the first important component. The energy dissipater element is another one that has a significant impact on how the self-centering system behaves. Using the damper as a replaceable and affordable tool and fuse in self-centering frames has been recommended to boost energy absorption and dampening of structural systems during earthquakes. In this research, the self-centering steel moment frame connections are equipped with cushion flexural dampers (CFDs) as an energy dissipator system to increase energy absorption, post-yielding stiffness, and ease replacement after an earthquake. Also, it has been carefully considered how to reduce permanent deformations in the self-centering steel moment frames exposed to seismic loads while maintaining adequate stiffness, strength, and ductility. After confirming the FE model's findings with an earlier experimental PT connection, the behavior of the self-centering connection using CFD has been surveyed in this study. The FE modeling takes into account strands preloading as well as geometric and material nonlinearities. In addition to contact and sliding phenomena, gap opening and closing actions are included in the models. According to the findings, self-centering moment-resisting frames (SF-MRF) combined with CFD enhance post-yielding stiffness and energy absorption with the least amount of permeant deformation in a certain CFD thickness. The obtained findings demonstrate that the effective energy dissipation ratio (β), is increased to 0.25% while also lowering the residual drift to less than 0.5%. Also, this enhancement in the self-centering connection with CFD's seismic performance was attained with a respectable moment capacity to beam plastic moment capacity ratio.

• 소성∙가공
• /
• 제18권1호
• /
• pp.45-51
• /
• 2009

Shape memory alloy has been used to improve the tensile strength of composite by the occurrence of compressive residual stress in matrix using its shape memory effect. In order to fabricate shape memory alloy composite, TiNi alloy fiber and Al2024 sheets were used as reinforcing material and matrix, respectively. In this study, TiNi/Al2024 shape memory alloy composite was made by using hot press method. In order to investigate bonding condition between TiNi reinforcement and Al matrix, the micro-structure of interface was observed by using optical microscope and diffusion layer of interface was measured by using Electron Probe Micro Analyser. And the mechanical properties of composite with three parameters(volume fraction of fiber, cold rolling amount and test temperature) were obtained by tensile test. The most optimum bonding condition for fabrication the TiNi/Al2024 composite material was obtained as holding for 30min. under the pressure of 60MPa at 793K. The strength of composite material increased considerably with the volume fraction of fiber up to 7.0%. And the tensile strength of this composite increased with the reduction ratio and it also depends on the volume fraction of fiber.