• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 D
• /
• pp.2561-2563
• /
• 2000

In this paper, a mathematical vehicle model, the braking force control parameters, the wheel control logic, and vehicle control strategy are presented, in order to analyze the dynamic characteristics of a vehicle equipped with ABS(Antilock Brake System). The full vehicle dynamics model is constructed with sprung mass, brake system, and wheels to verify control algorithms. The valve control algorithms are designed with the wheel accelerations and slip ratio take into consideration. Theses algorithms are applied to the front and rear wheels independently. Simulation is performed under the wet road condition at initial braking speed of 60 [km/h].

• 한국자기학회지
• /
• 제14권1호
• /
• pp.25-28
• /
• 2004

Ta/NiFe/Cu/Co 구조의 Pseudo 스핀밸브 박막을 제작하여 NiFe, Cu, Co 각 층들의 두께변화에 따른 자기저항비(MR-ratio), 보자력, 자기 민감도(sensitivity), 반전자장(Switching Field)의 크기 등의 자기적 특성을 연구하였다. 각 층들의 두께를 변화시키면서 측정한 결과 Ta(4 nm)/NiFe(7.5 nm)/Cu(3 nm)/Co(5 nm)에서 최대 자기저항비 7.26 %를 얻을 수 있었다. 또한 각 층들의 독립적인 자화 과정을 통해 자기저항 특성을 조절할 수 있었다. 특히 Co의 두께를 변화시켜 자기저항비를 비교적 일정하게 유지하면서 보자력의 크기를 조절할 수 있음을 알게 되었다.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.161-168
• /
• 2000

Lean combustion in a SI engine is one of the best solution for the improvement of fuel economy and reduction of pollutant emission. In order to access a lean combustion engine, stable combustion at lean AlF ratio is needed. In this paper, the effect of fuel injection timing on lean misfire limit has been investigated in an MPI engine. To investigate the interaction of injection timing and intake flow characteristics, three different swirl generating SCV(swirl control valve) configurations were considered, and investigated their effects on lean misfire limit and torque at full load operation. Also the effects of spark timing on lean combustion has been investigated. Lean combustion has been examined and the results are reported in this paper. SCV B has been developed to satisfy the requirements of sufficient swirl generation to improve lean combustion and stable performance. It is found that injection timing, spark timing and intake air motion govern the stable lean combustion.

• 설비공학논문집
• /
• 제20권12호
• /
• pp.775-780
• /
• 2008

A dynamic model to simulate LNG reliquefaction process has been developed. The model was applied to two candidate cycles for LNG reliquefaction process, which are Reverse Brayton and Claude cycles. The simulation was intended to simulate the pilot plant under construction for operation of the two cycles and evaluate their feasibility. According to the simulation results, both satisfy control requirements for safe operation of brazed aluminum plate-fin type heat exchangers. In view of energy consumption, the Reverse Brayton cycle is more efficient than the Claude cycle. The latter has an expansion valve in addition to the common facilities sharing with the Reverse Brayton cycle. The expansion valve is a main cause to the efficiency loss. It generates a significant amount of entropy associated with its throttling and increases circulation flow rates of the refrigerant and power consumption caused by its leaking resulting in lowered pressure ratio. It is concluded that the Reverse Brayton cycle is more efficient and simpler in control and construction than the Claude cycle.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제17권4호
• /
• pp.135-140
• /
• 2009

A dynamic model to simulate LNG reliquefaction process has been developed. The model was applied to two candidate cycles for LNG reliquefaction process, which are Reverse Brayton and Claude cycles. The simulation was intended to simulate the pilot plant under construction for operation of the two cycles and evaluate their feasibility. According to the simulation results, both satisfy control requirements for safe operation of brazed aluminum plate-fin type heat exchangers. In view of energy consumption, the Reverse Brayton cycle is more efficient than the Claude cycle. The latter has an expansion valve in addition to the common facilities sharing with the Reverse Brayton cycle. The expansion valve is a main cause to the efficiency loss. It generates a significant amount of entropy associated with its throttling and increases circulation flow rates of the refrigerant and power consumption caused by its leaking resulting in lowered pressure ratio. It is concluded that the Reverse Brayton cycle is more efficient and simpler in control and construction than the Claude cycle.

• 설비공학논문집
• /
• 제15권5호
• /
• pp.382-388
• /
• 2003

Refrigerant flow rates of the multi-type air-conditioning system can be regulated by electronic expansion valves (EEV). The performance of the multi-type air-conditioning system may be improved by lowering the superheat at the compressor suction side. In this study, a superheat temperature setpoint reset algorithm was developed by using fuzzy logics, and a PI algorithm was applied to control the superheat temperature near setpoints. Experimental results showed energy savings and stable operations at a multi-type air-conditioning system. Therefore, the developed setpoint reset algorithm may be effectively used for the EEV superheat temperature control of the multi-type air-conditioning system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.287-288
• /
• 2007

This paper is for a Real-time Active Control System to operate a boiler. By sensing of flame we wanted to get status of a furnace as many as possible, like load, efficiency, and/or amount of pollutant. These data can be used to make optimal running point by controlling the ratio of air and fuel. So the last object is to make a closed actual control loop from optical head to valve controllers. The first job was to design and to develop a optical data acquisition system. including optical sensor module. And we gathered flame data in variable situations for taking the trend of flame against burning environment. Currently we are developing a general system model, designing some control strategy and testing this active control system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.110-110
• /
• 2000

In this paper, an antilock brake system (ABS) for commercial vehicles is studied by considering the design of a fuzzy Logic controller with pulse width modulation (PWM). PWM method is used for generating solenoid valve inputs in order to cope with the chattering problem caused by the conventional on/off control The sliding mode observer is designed to estimate the vehicle longitudinal velocity and it is used to calculate the wheel slip ratio. The effectiveness of the proposed control algorithm was validated by simulations performed with a nonlinear 14-DOF vehicle model including the dynamics of the brakes.

• 한국공작기계학회논문집
• /
• 제13권2호
• /
• pp.69-74
• /
• 2004

In general the surge pressure generated in hydraulic systems causes noise, vibration and odd effect to the system. To reduce the surge pressure, high frequency PWM control of 20KHz was attempted. To estimate the braking noise caused by surge, a vehicle equipped with on-board ABS hydraulic modulator has been experimented with respect to the various breaking condition. Thorough this experiments, it was found that breaking noise has been reduced using high frequency PWM control method compare with low frequency method. To evaluate high frequency control m practice, including verification of general functionality, EMI tests was experimented. Its was found that it is necessary to have the solution to electromagnetic interference(EMI) generated by switching elements.

• 해양환경안전학회지
• /
• 제25권7호
• /
• pp.953-960
• /
• 2019

밀러 사이클은 흡입밸브 닫힘 시기 조정을 통해 압축비를 줄임으로써 NOx의 저감과 연료소비율 개선이 동시에 가능하다는 점(밀러 효과)에서 디젤엔진에 매우 활발하게 채택되어지고 있다. 밀러 사이클은 흡입 밸브를 BDC 이전에 닫는 Early 밀러 방식과 BDC 이후에 닫는 Late 밀러 방식으로 나눌 수 있다. 저속에서는 체적효율의 증가를 꾀할 수 있는 Late Miller가 유리한 반면, 중속, 고속에서는 IVC 이후 BDC 까지의 피스톤 하강 과정의 흡기의 팽창에 따른 내부 온도 감소 효과 높은 Early 밀러가 유리하다. 따라서 Early 밀러와 Late 밀러의 효과를 고려하여 운전 조건에 적합한 밀러 구현 방법을 채택할 필요가 있다. 본 연구에서는 4행정 엔진을 대상으로 2단 과급 시스템의 적용하고 흡·배기 밸브 오버랩(valve overlap)의 감소를 통해 밀러 효과를 강화하는 과정과 밸브 조정 기구를 통한 밸브 조건의 변화가 밀러 효과에 미치는 영향을 고찰하였다. 결과적으로 2단과급과 밀러사이클, 밸브 오버랩 감소와 흡입밸브 리프트 증가를 통해 연료소 비율과 최고연소온도 감소의 효과를 확인하였다.