• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.138-141
• /
• 2002

BLDCM(Brushless D.C. Motor) is widely used for industrial application because of high efficiency and high power density Especially, in servo system and home appliance, BLBCM is very useful due to high control performance and low acoustic noise. In this paper, 2.5HP rated BLDCM controller and drive was developed for tread mill application. The prototype BLDCM has 4 poles rotor and 24 slots stator. Ferrite was used as a rotor magnet due to the cost and temperature characteristic. For the stable operation of tread mill, over current and high temperature can be detected by the DSP controller. For the commutation signal, switching patterns from the sensorless circuit and hall sensor signal are used in the DSP controller.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.99-103
• /
• 2003

Recently, a fuel cell with low voltage and high current of electronic output characteristics is remarkable for new generation system. It needs both a dc-dc boost converter and do-ac inverter to be used in domestic power. Therefore, this paper presents do-dc boost converter with ZVS for fuel cell generation system This topology has several advantages, which are ZVS characteristics of all of main and auxiliary switches, reduction of reactor component size because of high frequency switching, and low rated voltage stress of the switches. In this paper, theoretical analysis, operation principle, and design procedures are presented. And simulation results from Pspice are presented to validate the theoretical analysis.

• Journal of Power Electronics
• /
• v.11 no.4
• /
• pp.418-423
• /
• 2011

This paper presents a simulation model and a parameter identification scheme of an induction motor drive for electric vehicle. The induction motor in automotive applications should operate in very high efficiency and achieve the maximum-torque-per-ampere (MTPA) feature even with saturated magnetic flux under very high torque. The indirect vector control which is typically adopted in traction drive system requires precise information of motor parameters, particularly rotor time constants. This work models an induction motor considering magnetic saturation and proposes an empirical identification method using the current controller in the synchronous reference frame. The proposed method is applied to a 22kW-rated induction motor for electric vehicle.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.33-35
• /
• 1999

This paper describes the test results of the single phase 3kVA high temperature superconducting power trans-former. The tapes are made with Bi-2223 and have silver alloy as the matrix. Four double pancake windings are used in total. Among them two double pancake windings are connected in series for high voltage winding and two double pancake windings are connected in parallel for low voltage winding. The rated voltages of each winding are 220/110 V. Fundamental characteristics are obtained through short circuit and no load tests. The over load capability and characteristics are investigated.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 1998.11a
• /
• pp.154-157
• /
• 1998

This study investigated the psychological and physiological responses to the sound of car horns produced by different. manufacturers. Ten female college students listened to the sound of the horns while their EEG responses on 6 sites were being measured, and rated each hem on psychological scales. Their EEG and psychological responses were investigated as to whether the responses were related to the loudness, sharpness, tonality, and roughness of the horns. The results indicated that the subjects felt more 'dominated' as the loudness and sharpness increased, that the subjects felt more 'pleasant' as the sharpness increased, that the subjects felt more 'dominant' as the tonality increased, and that the subjects felt more 'aroused' as the roughness increased. The physiological results showed that the fast alpha wave in the occipital lobe decreased in the relative power as the loudness, sharpness, and tonality increased, and that the delta wave in the occipital lobe increased and the slow alpha wave in the frontal lobe decreased in the relative power as the roughness increased.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.598-603
• /
• 2005

Biogas produced from anaerobic digestion processes has about 60% of methane and about 40% of carbon dioxide. Raw biogas can be used in internal combustion engines either spark ignition or diesel engines. Since the gas has relatively low calorific values, engine power also is lower than rated power values. Modified engines or biogas-specific engines have been utilized in order to increase efficiency. Another option is gas cleansing for increasing its calorific values. A couple of European countries adopted this approach in using biogas for one of transportation fuels, such as $CO_2$ scrubbing with water or special solutions. This study reports the results of water scrubbing for reducing $CO_2$ concentration. In 2.5m-high PVC pipe accepting water, $CO_2$ reduction rates were investigated. When flow rate of $CO_2$ and air mixture was about 5 LPM, $CO_2$ concentration was decreased up to 70%. Higher calorific biogas through water scrubbing is expected to be applied to various commercial engines without costly modification.

• 전기의세계
• /
• v.18 no.2
• /
• pp.7-14
• /
• 1969

From the first customer located right at the substation to the last customer at the end of the line, voltage must be held within close limits, so the voltage regulation is more important than the thermal limit. On a typical distribution system during the peak load period, the voltage drop may be serious enough to cause unsatisfactory operation of home appliances in the residential area, and present many problems to manufacturing industries, where the voltage must be maintained within close limits to insure smooth operation. Among all the factors contributing to voltage drop in the distribution system, the voltage drop in the distribution transformer may account for 30% of this figure. If we can eliminate this factor, the power companies can provide better quality electricity to more customers with the existing distribution facilities, thus saving on initial investment costs. Taking all these problems into consideration, the author undertook the design of a capacitive transformer which would give zero voltage drop at rated load and at 80% lagging power factor while incorporating overload features to withstand 400% overload for at least 100 seconds. The following are the results obtained through design, manufacture and test of an initial experimental transformer built with these specific purposes.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.104-108
• /
• 2004

Micro turbine is an electric power generating system using a gas turbine whose rated power is under 300kW, and it is featured as a small, efficient. maintenance free and environment-friendly system. Air foil bearing has several advantages over conventional bearings for micro turbine because it is oilless and non-contact. Recently, air foil bearings for high temperature over $500^{\circ}C$ has been developed for the application of 65kW micro turbine system. In this paper, the development and current status are summarized in detail.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1524-1526
• /
• 2000

Two stator windings for high voltage motor(rated 6.6kV) were manufactured with mica tape/varnish(No. 1). and mica tape(No. 2). Electrical tests included ac current, tan $\delta$ and partial discharge magnitude in these stator windings. Electrical properties showed that No. 1 stator winding was better than that of No. 2. Microstructure properties were conducted using scanning electron microscope(SEM) in the cross section of the straight stator windings. SEM results indicated that the mica tape interface of No. 1 stator winding was larger than that of No. 2 stator winding.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1005-1007
• /
• 2005

Small wind turbines are becoming a viable technology option to supply electricity to landowners. These systems provide energy security, product relatively no environmental harm, and in an appropriate setting can be quite cost-competitive with traditional electricity options. This paper is dealing with the methods how to overcome such inconvenience and with the analysis of characteristic and a field test with a prototype of the stand alone wind turbine was performed. The method applies to small systems, equipped with a coreless axial-flux permanent magnet(AFPM) generator in the turbine, a dc-dc converter and batteries. The analysis concentrates on the effect of the load on the power-wind speed curve of the turbine. The system is designed for direct driven, coupled with turbine and generator with a rated power of, 3kW.