• Korean Journal of Clinical Laboratory Science
• /
• v.50 no.2
• /
• pp.136-143
• /
• 2018

The rate pressure product (RPP) is expressed as a product of the heart rate and systolic blood pressure as an index indirectly measuring the myocardial oxygen consumption, and it indicates the burden on the myocardium. The aim of this study was to determine the optimal level of RPP for preventing metabolic syndrome in a treadmill exercise test in Korean adults. Metabolic syndrome was the diagnosis of the third executive summary report on the National Cholesterol Education Program Adult Treatment Panel III (NCEP-ATP III) criteria. According to the criteria, the metabolic syndrome diagnosis group (MetS, N=25), pre-metabolic syndrome group (Pre-MetS, N=106), and non-risk factor group (Non-MetS, N=65) were classified. The exercise stress test was performed based on the Bruce protocol. The RPP was calculated as (heart rate${\times}$systolic blood pressure)${\div}1,000$. The results showed that the maximum systolic blood pressure was high despite the low daily dose reached in the diagnostic group of metabolic syndrome. The optimal threshold of the RPP at the time of the exercise treadmill test for a metabolic syndrome prediction was $12.56mmHg{\times}beats/min{\times}10^{-3}$ in the first stage of the exercise stress test. The second stage of the exercise test was $16.94mmHg{\times}beats/min{\times}10^{-3}$, and at the third stage of the exercise test was $21.11mmHg{\times}beats/min{\times}10^{-3}$.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1042-1044
• /
• 1995

This paper provides the results and analyses of investigations into porcelain suspension insulators failures on the KEPCO system. The high failure rate of suspension insulators on distribution lines has been attributed to the volume expansion of the cement, the insulation puncture breakdown of the porcelain and the power arc failure. The utility must use only the good insulators and at least reduce the insulator failure rate. So, this paper recommends that the utility make test criteria(cement expansion test, steep front-of-wave flashover voltage test and power arc test. etc) on the suspension insulators.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.59-66
• /
• 1999

ILT proposed by Tezaghi was frequently used which is based on one dimensional consolidation theory. But this test require time longer than a week and has problems for extra soft clay such as the squeezing around the consolidation ring. Also consolidation curve is not clearly defined since only a few data is obtained in a test. Therefore it is difficult to determine Pc and the interpretation to determine the consolidation constants are rather complicated. In this paper, the stress-strain relationship and consolidation constant obtained by CRS and CG-test were analyzed and compared with the results by ILT.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.967-973
• /
• 2004

Electro-pneumatic servo valve is an electro-mechanical device which converts electric signals into a proper pneumatic flow rate or pressure. In order to improve the overall performance of pneumatic servo systems, electro-pneumatic servo valves are required, which have fast dynamic characteristics, no air leakage at a null point, and can be fabricated at a low-cost. The first objective of this research is to design and to fabricate a new electro-pneumatic servo valve which satisfies the above-mentioned requirements. In order to design the mechanism of the servo valve optimally, the flow inside the valve depending upon the position of spool was analyzed variously, and on the basis of such analysis results, the valve mechanism, which was formed by combination of the spool and the sleeve, was designed and manufactured. And a tester for conducting an overall performance test was designed and manufactured, and as a result of conducting the flow rate test, the pressure test and the frequency test on the developed pneumatic servo valve.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.3
• /
• pp.89-97
• /
• 2002

In this study, the effect of $\alpha$-phase morphology on the dynamic deformation behavior at ultra high strain rate was investigated by EBW(Explosive Bridge Wire) test. All of tests and analyses were conducted on three typical microstructures of Ti-6Al-4V alloy, i.e. equiaxed, widmanstatten and bimodal microstructures. The spall strength and HEL(Hugoniot Elastic Limit) of the specimens that have the thickness of 2mm and 4mm were highest with the bimodal microstructure. These results were similar with previous study which was performed by dynamic torsion test(Kolsky torsion test).

• Computers and Concrete
• /
• v.8 no.3
• /
• pp.243-278
• /
• 2011

The paper presents simulations of the Brazilian test using two numerical models. Both models are regularized in order to obtain results independent of discretization. The first one, called gradient damage, is refined by additional averaging equation which contains gradient terms and an internal length scale as localization limiter. In the second one, called viscoplastic consistency model, the yield function depends on the viscoplastic strain rate. In this model regularization properties are governed by the assumed strain rate. The two models are implemented in the FEAP finite element package and compared in this paper. Parameter studies of the split test are performed in order to point out the features of each model.

• Elastomers and Composites
• /
• v.28 no.4
• /
• pp.283-292
• /
• 1993

The morphology and impact strength of alloys of high density polyethylene(HDPE) and nylon-6(PA) with modified $ethylene-{\alpha}-olefin$ copolymer(OCP) as compatibilizer and impact modifier were measured by the scanning electron microscope(SEM) and the notched Izod impact test(and the high rate impact test), respectively. HDPE is incompatible with PA and specimens obtained from simple mechanical mixing show the inferior properties. However, it was indicated that OCP played roles of not only impact modifier but also compatibilizer. High rate impact test results were different from those of the notched Izod impact test, but in both tests OCP was effective for HDPE/PA blends. From SEM observation, the size of the dispersed phase in alloys prepared with OCP is much smaller than that of alloys without OCP and the interfacial adhesion of alloys prepared with OCP is also better. Toughening mechanism of polymer blends was discussed by combining the morphology analysis with mechanical and thermal properties.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.263-268
• /
• 1999

With HAZ of A 106 Gr B steel weldment, fatigue test in air, electrochemical polarization test and corrosion fatigue test in 3.5wt.% NaCl solution were performed changing load ratio. Obtained results are as follows. 1) K$\sub$op/ was independent of K$\sub$max/ and load ratio in fatigue crack growth. 2) In variation of load ratio, the scatter band of crack growth curve was reduced by half considering crack closure 3) In the result of electrochemical polarization test, current density was increased abruptly when potential was larger than corrosion potential. 4) Fatigue crack growth rate in corrosive environment was markly higher than the rate in air because of corrosion characteristics of the material and anodization of inner surface crack.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.151-158
• /
• 2007

The mechanism of power transmission from motor torque to stem thrust and the operation characteristic of each stroke position are analyzed using the diagnostic signal, and effects of differential pressure on the performance of motor operated flexible wedge gate valve are investigated. Test facility consists of 76 mm motor operated valve(flexible wedge type), pump and pipe system. Static and dynamic test are performed separately, and two differential pressure conditions are applied in the dynamic test. To evaluate the performance of valve, test signals for the torque, thrust, current, voltage and stroke length are acquired by using UDS which is diagnosis device for motor operated valve, and each diagnostic signal is analyzed and compared. The characteristic of valve performance factors such as stem factor, rate of loading, valve factor, are evaluated, and these factors are found to be severely influenced by the fluid differential pressure.

• International Journal of Reliability and Applications
• /
• v.4 no.2
• /
• pp.57-69
• /
• 2003

A non-parametric test based on U-statistic for testing exponentiality against the new better than used renewal failure rate (NBURFR) alternatives is introduced and the percentiles of this test statistic are tabulated for sample size 5(1)50. Its properties are also discussed including the Pitman asymptotic efficiency relative to the tests of the new better than used and new better than used failure rate (Ahmed (1994) and Hendi (2000)). The powers of this test are also calculated for some used life distributions. An example from blood cancer patients demonstrates a practical application of our test in the medical sciences is presented. Finally the problem when right-censored data is available is handled.