• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.916-922
• /
• 1986

This paper presents the preliminary results of an experimental study on surface crack growth under fatigue loadings. The objective of this paper is to assess the effect of the initial crack size on crack propagation behaviors. Transparent PMMA plate speciments with shallow circular arc notch were used. Crack growth behaviors were observed and measured in two directions by travelling microscopes. The fatigue crack initiated at the deepest part on the initial arc shaped notch and then propagated to depth direction as well as spreading gradually along the notch tip. A considerable number of cycles was needed until the depth crack spreaded to the surface notch tip. When the fatigue crack reached the surface notch tip the crack front became an approximate semi-ellipse, primary semi-elliptical crack. Test results suggest that the relationships between fatigue crack growth rate and stress intensity factor range in both directions can be expressed by power law (Paris) and that relationship in width direction depends upon the crack ratios a$_{1}$/b$_{1}$, of the primary semi-elliptical crack. The relationship between the nondimensional crack lengths in both directions can be represented as the formula: (a/t)$^{n}$ =B(2b/W+A) where n and A are constants and B is seems to be depended upon the crack ratio a$_{1}$/b$_{1}$.

• Radiation Oncology Journal
• /
• v.5 no.2
• /
• pp.157-163
• /
• 1987

It is known that fixed source to skin distance (SSD) cannot be used when the treatment field is sloped or larger than the size of second collimator in electron beam irradiation and inverse square law using effective ssd should be adopted. Effective SSDs were measured in different field sizes in each 6, 9, 12, 15 and 18MeV electron energy by suing NELAC 1018D linear accelerator of Kosin Medical Center. We found important parmeters of effective SSD. 1. Minimum effective SSD was 58.8cm in small field size of $6\pm6cm$ and maximum effective SSD was 94.9cm in large field size of $25\pm25cm$, with 6MeV energy. It's difference was 36.1cm. The dose rate at measuring point was quite different even with a small difference of SSD in small field $(6\times6cm)$ and low energy (6 MeV). 2. Effective SSD increased with field size in same electron energy. 3. Effective SSDs gradually increased with the electron energies and reached maximum at 12 or 15 MeV electron energy and decreased again at 18MeV electron energy in each identical field size. And so the effective SSD should be measured in each energy and field size for practical radiotherapy.

• Economic and Environmental Geology
• /
• v.41 no.2
• /
• pp.253-265
• /
• 2008

Sustainable resource management(SRM) is regarded as the core strategy to achieve Dematerialisation and Decoupling of economic growth from the use of natural resources and environmental degradation. This paper presents status SRM policy and research in worldwide, and analyzes decoupling of economic activity from energy consumption of domestic manufacturing, using decoupling factor. Also This paper suggests methodologies and strategies of SRM in Korea. SRM is established through various analysis and survey as following; forecasting of resource demand, material flow analysis and value chain analysis, resource market structure analysis. Through these analysis, we can obtain hot-spot and solution of environmental burden, recycling market management, recycling technology and best-optimal supply rate of primary and secondary resource. In Korea, resource management system must be linked with national and regional material flow analysis, and it is necessary to make SRM-law of national dimension for effective run of sustainable resource management system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5039-5044
• /
• 2015

In this study, we evaluated corrosion behavior of a common rolling stock axle material, RSA1, in seawater. 3-electrode electrochemical cell experiment was conducted using artificial sea water, fabricated according to ASTM-D1141 set by American Society for Testing and Materials, where the corrosion current density and corrosion rate were determined to be $18.3{\mu}A/cm2$ and 0.217 mm/yr, respectively, by employing potentiodynamic test method and impedance spectroscopy method. Considering the fact that life time of railway car is ~25 years, the expected corrosion layer depth is 5mm. Constant-current corrosion test was conducted to accelerate the corrosion process, to reach corrosion periods of 1,3 and 4 years based on Faraday's law, followed by tension tests where the reduced specimen gauge cross-section was re-measured for stress calculation. While no apparent corrosion-related changes in mechanical properties were observed in the elastic regime, the reduction in ductility of the material was found to be increased as the corrosion period increased. The results of this study are expected to be basic corrosion data for the design of rolling stock axles, which will be operated in the sea water environment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.5327-5332
• /
• 2014

In Korea, the quantitative growth rate of artificial reef construction is supposed to reach the peak point. Therefore, new approach is needed to the point of artificial reefs business. Functional reefs, such as shellfish reefs, recreational reefs, seaweed reefs, and fish reefs, are beneficial alternatives. This study conducted hydraulic testing to assess the stability of corrugated artificial reefs (ARs) that were constructed to promote the growth of shellfish and seaweed. The results of this study showed that some dimensionless design parameters affected the stability of corrugated artificial reefs under a range of wave and water depth conditions in a fixed bed condition. The findings also highlight the importance of hydraulic experiments in solving the problems that have emerged in the design and construction of artificial reefs.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.39-44
• /
• 2008

Magnesium alloys have given high attention to the industry of light-weigh as automobile and electronics with aluminium, titanium and composite alloys due to their high strength, low specific density and good damping characteristics. But the magnesium contained structures under high temperature have the problems related to creep deformation and rupture life, which is a reason of developing the new material against creep deformation to use them safely. The purpose of this study is to predict the creep deformation mechanism and rupture time of AZ31 magnesium alloy. For this, creep tests of AZ31 magnesium alloy were done under constant creep load and temperature with the equipment including automatic temperature controller with acquisition computer. The apparent activation energy Qc and the applied stress exponent n, rupture life have been determined during creep of AZ31 Mg alloy over the temperature range of $150^{\circ}C$ to $300^{\circ}C$. In order to investigate the creep behavior. Constant load creep tests were carried out in the equipment including automatic temperature controller, whose data are sent to computer. At around the temperature of $150^{\circ}C{\sim}300^{\circ}C$ the creep behavior obeyed a simple power-law relating steady state creep rate to applied stress and the activation energy for the creep deformation was nearly equal and a little low, respectively, to that of the self diffusion of Mg alloy.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.135-141
• /
• 2005

Nitric oxide(NO) reduction by methanol was investigated over $La_2O_3$ catalysts in the presence and absence of oxygen. In the absence of $O_2$, $CH_3OH$ reduced NO to both $N_2$ and $N_2O$, with selectivity to $N_2$ formation decreasing from 81-88% at 623K to 47-71% at 723 K. With 1.2% $O_2$ in the feed, the rates were 4-8 times higher, but the selectivity to $N_2$ dropped from 50% at 623 K to 9% at 723 K. The specific activities with $La_2O_3$ for this reaction were higher than those for other reductants; for example, at 773 K with hydrogen a specific activity of $34\;{\mu}mol\;NO/sec{\cdot}m^2$ was obtained whereas that for methanol was $638\;{\mu}mol\;NO/sec{\cdot}m^2$. The Arrhenius plots were linear under differential reaction conditions, and the apparant activation energy was consistantly near 15 kcal/mol with $CH_3OH$. Linear partial pressure dependencies based on a power rate law were obtained and showed a near-zero order in $CH_3OH$ and a near-first order in $H_2$.

• Journal of the Korean Society of Food Culture
• /
• v.17 no.3
• /
• pp.225-239
• /
• 2002

This is the research on the observing annual customs, the annual custom foods and the application of the annual custom foods to the school foodservice. We sample 419 housewives live in Kyungnam area and 174 dieticians work at the primary and secondary schools. Annual customs the housewives and dieticians observe at high degree are Chuseok, Seolral, Jeongwoldaeboreum, Dongji, Chopail, Sambok etc. The housewives observe more Seolral, Chuseok and Dongji than the dieticians and the dieticians observe more Sambok than the housewives.(P<.001) When they provide school foodservice, the dieticians observe Dongji at the highest degree. In Kyungnam they eat most the gakjongnamul as annual custom foods on Chuseok and Seolral. They eat most ogokbap and mugeunnamul on Jeongwoldaeboreum, minarinamul on Chopail, and samgyetang on Sambok and patjuk on Dongji as the annual custom foods. Most of dieticians (94.3%) answer that it is good to provide annual custom foods as the school foodservice on annual customs. However, they indicate some practical problems to do such as inadequacy of the school cooking facilities, its not suiting students' tastes, etc. The rate of housewives' answers that we have to transmit annual customs is higher than that of dieticians.(P<.001) Seolral topped the list of annual customs both housewives and dieticians answer must be transmitted, followed by Chuseok, Jeongwoldaeboreum, Dongji. Dongji is followed by Chopail(P<.001) in the housewives' answers while Sambok(P<.001) in the dieticians' answers. Though most of the respondents know the origins, dates and details of annual customs they think must be transmitted, they don't know well those of the other ones. By their mothers both housewives and dieticians have come to know about annual customs and mostly affected. Secondly housewives affected by their mothers-in-law while dieticians by their school education.(P<.001)

• Journal of the Korean Society of Food Culture
• /
• v.9 no.5
• /
• pp.467-478
• /
• 1995

The school food service system has been an important national policy in Korea. To find out the reference data of the school food service system, we surveyed four primary schools, one middle school, and one food service center in Nara, Japan. The results are as follows; 1. The school food service was carried out in 99.4% of primary school children and in 82.5% of middle school students. 2. The central commissary school food service system was utilized at 49.0% of primary schools and 68.5% of middle schools. 3. The expense of the system is supported partially by the student's parents and partially by the government, of which the support rate was noticed by the law of school food service. 4. The dietary content of school food service was laid down by 'The rule of the operation basis of school food service'. The menu was chosen by the 7 kinds of stepwise meetings. 5. The teachers emphasized on the food etiquette, the appreciation to the food and the personal relationship during meal, as well as on the nutritional balance. 6. We found other problems in Japanese food service system, such as the sanitary problems, the problems of the new tableware, and whether the central kitchen had less advantage than the individual school kitchen. We can conclude that the school food service system is becoming the essential part in school education, and hope to design not only economical but also educational system in Korea, with the consideration of Japanese system.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.5
• /
• pp.406-412
• /
• 2003

FT-IR and thermography were used to investigate the infrared radiation characteristic of SiO$_2$ film and SiO$_2$/Fe$_2$O$_3$film coated on aluminum. Through FT-TR spectrum, SiO$_2$film showed high infrared absorption in accordance with the stretching vibration of Si-O-Si, and as$ Fe_2$$O_3$was mixed additional absorption band appeared resulting from the stretching vibration of Fe-O at $590cm^{-1}$ and the bond of Si-O-Fe at $900 cm^{-1}$ The two kinds of film measured by the integration method and the reflective method coincided with each other in the wavelength area of infrared absorption and radiation, and corresponded well with Kirchhoff's law as the infrared emissivity is high in wavelength where infrared absorption rate is high. The emissivity of $SiO_2$ film was 0.65 and that of $SiO_2$/Fe$_2$$O_3$film was 0.77, so the addition of$ Fe_2$$O_3$ raised the infrared emissivity by approximately 13%.$ SiO_2$$Fe_2$$O_3$ film is efficient as an infrared radiator at below $100^{\circ}C$. The temperature of heat radiation after 7 minutes was 117$^{\circ}C$ in aluminum plate and $155^{\circ}C$ in $SiO_2$$Fe_2$$O_3$ film, $38^{\circ}C$ higher than the former.