• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.114-120
• /
• 1994

We have been successfully fabricated the low nois HEMT device with AlGaAs and GaAs structure. The epitazial layer with n-type AlgaAs and undoped GaAs was grown by molecular beam epitaxy(MBE) system. Ohmic resistivity of the ource and drain contact is below 5${\times}10^{6}{\Omega}{\cdot}cm^{2}$ by the rapid thermal annealing (RTA) process. The ideality factor of the Schottky gate is below 1.6 and the gate material was Ti/Pt/Au. The HEMTs with 0.25$\mu$m-long and 200$\mu$m-wide gates have exhibited a noise figure of 0.65dB with associated gain of 9dB at 12GHz, and a transconductance of 208mS/mm.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.1
• /
• pp.41-47
• /
• 2010

The effects of thermal treatment on CNTs, which were coated with a-$CN_x$ thin film, were investigated and related to variations of chemical bonding and morphologies of CNTs and also properties of field emission induced by thermal treatment. CNTs were directly grown on nano-sized conical-type tungsten tips via the inductively coupled plasma-chemical vapor deposition (ICP-CVD) system, and a-$CN_x$ films were coated on the CNTs using an RF magnetron sputtering system. Thermal treatment on a-$CN_x$ coated CNT-emitters was performed using a rapid thermal annealing (RTA) system by varying temperature ($300-700^{\circ}C$). Morphologies and microstructures of a-$CN_x$/CNTs hetero-structured emitters were analyzed by FESEM and HRTEM. Chemical composition and atomic bonding structures were analyzed by EDX, Raman spectroscopy, and XPS. The field emission properties of the a-$CN_x$/CNTs hetero-structured emitters were measured using a high vacuum (below $10^{-7}$ Torr) field-emission measurement system. For characterization of emission stability, the fluctuation and degradation of the emission current were monitored in terms of operation time. The results were compared with a-$CN_x$ coated CNT-emitters that were not thermally heated as well as with the conventional non-coated CNT-emitters.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.1-6
• /
• 2000

X-ray lithography mask with SiC membrane and Ta absorber patterns has been fabricated using ECR plasma CVD, d.c. magnetron sputtering, and ECR plasma etching. The stress of stoichiometric SiC film was adjusted by rapid thermal annealing under $N_2$, ambient. Adjusting the working pressure during sputtering process resulted in a near-zero residual stress, reasonable density, and smooth surface morphology of Ta film. Cl-based plasma showed a good etching characteristics of Ta, and two-step etching process was implemented to suppress microloading effect fur sub-quarter $\mu\textrm{m}$ patterning.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.1
• /
• pp.45-51
• /
• 2001

The effects of wettability and surface oxidation on the low temperature and ultra-fine solder bump formation have been studied. Difference sequences of near eutectic In-Ag and eutectic Bi-Sn solders were evaporated on Au/Cu/Cr or Au/Ni/Ti Under Bump Metallurgy (UBM) pads. Solder bumps were formed using lift-off method and were reflowed in Rapid Thermal Annealing (RTA) system. The solder bumps in which In was in contact with UBM in In-Ag solder and the solder bumps in which Sn was in contact with UBM in Bi-Sn solder showed better bump formability during reflow than other solder bumps. The ability to form spherical solder bumps was affected mainly by the wettability of solders to UBM pads.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.1
• /
• pp.36-43
• /
• 2000

The sulfur pressure and TRA(rapid thermal annealing) conditions of the fabricated SrS:CuCl TFEL devices were optimized to improve blue color luminance. The thickness of the phosphor layer of SrS:CuCl TFEL devices fabricated by electron beam deposition system was 6000 ~ 8000 ${\AA}$. The fabricated TFEL devices were annealed at 800 $^{\circ}C$ for 3 min. It was shown that the crystallinity of SrS:CuCl phosphor was improved by an increase in RTA temperature and RTA time. Blue color was emitted from the TFEL device with emission peak wavelength of 468 nm and 500 nm. The CIE color coordinates were x = 0.21, y = 0.33. The luminance($L_{40}$) of TFEL device strongly depended on the sulfur pressure of deposition chamber and increased from 262 cd/$m^2$ to 728 cd/m2 as the sulfur pressure increased from $8{\times}10^{-6}$ torr to $2{\times}10^{-5}$ torr.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.181.2-181.2
• /
• 2014

A single-layer graphene has been uniformly grown on a Cu surface at elevated temperatures by thermally processing a poly (methyl methacrylate) (PMMA) film in a rapid thermal annealing (RTA) system under vacuum. The detailed chemistry of the transition from solid-state carbon to graphene on the catalytic Cu surface was investigated by performing in-situ residual gas analysis while PMMA/Cu-foil samples being heated, in conjunction with interrupted growth studies to reconstruct ex-situ the heating process. We found that the gas species of mass/charge (m/e) ratio of 15 ($CH_3{^+}$) was mainly originated from the thermal decomposition of PMMA, indicating that the formation of graphene occurs with hydrocarbon molecules vaporized from PMMA, such as methane and/or methyl radicals, as precursors rather than by the direct graphitization of solid-state carbon. We also found that the temperature for dominantly vaporizing hydrocarbon molecules from PMMA and the length of time, the gaseous hydrocarbon atmosphere is maintained, are dependent on both the heating temperature profile and the amount of a solid carbon feedstock. From those results, we strongly suggest that the heating rate and the amount of solid carbon are the dominant factors to determine the crystalline quality of the resulting graphene film. Under optimal growth conditions, the PMMA-derived graphene was found to have a carrier (hole) mobility as high as ${\sim}2,700cm^2V^{-1}s^{-1}$ at room temperature, which is superior to common graphene converted from solid carbon.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.351-352
• /
• 2012

UV LED에서 p-GaN층의 높은 일함수와 자체 면저항이 크기 때문에 current spreading layer인 ITO (indium tin oxide) 투명전극이 사용되고 있다. 따라서 높은 UV 파장대 투과율과 낮은 면 저항이 매우 중요하다. 본 연구에서, RF magnetron sputter를 사용하여 ITO 투명전극을 glass(boro33)에 120 nm 두께로 증착하였다. 그 후 RTA (rapid thermal annealing)을 이용해 120초 동안 $600^{\circ}C$에서 Air, $N_2$ (15 sccm), vacuum 환경에서 열처리를 하여 UV-Vis-NIR spectrophotometer를 사용해 ITO 박막의 투과율을 측정하고, Hall measurement system을 이용하여 전기적 특성을 측정하였다. Fig. 1과 같이 열처리 환경에 따라 ITO 박막의 투과율이 변하고 또한 Table 1과 같이 전기적 특성도 변함을 알 수 있었다. Air 환경에서의 열처리는 reference 샘플과 비교 했을 때 400 nm 이하의 파장에서 투과율이 증가하였지만 400 nm 이상의 파장에서는 투과율이 낮아짐을 볼 수 있고, 면 저항 (Ohm/sq)은 오히려 reference (as deposited) 샘플과 비교하여 24 Ohm/sq 증가하는 것을 알 수 있었다. 반면에 $N_2$, vacuum 환경에서 열처리는 reference (as deposited) 샘플 보다 380 nm 파장대에서 16% 정도 높은 투과율을 보였고, 면저항 역시 2배 이상 낮아졌다. 둘 다 비슷한 투과율과 면저항을 나타내었지만 vacuum 환경이 좀 더 우수한 광학적 특성을 나타내었고 반면에 $N_2$ 환경은 좀 더 낮은 면저항을 나타내었다. ITO 박막을 증착한 후 vacuum 환경에서 열처리를 통하여 제작된 UV-LED (중심 파장 380 nm)가 Fig. 2와 같이 입력 전류 450 mA에서 광출력이 46% 정도 향상 되었고 안정된 I-V 특성 보였다.

• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.135-139
• /
• 2015

$Cu_2SnS_3$ (CTS) based thin film solar cells (TFSCs) are of great interest because of its earth abundant, low-toxic and eco-friendly material with high optical absorption coefficient of $10^4cm^{-1}$. In this study, the DC sputtered precursor thin films have been sulfurized using rapid thermal annealing (RTA) system in the graphite box under Ar gas atmosphere for 10 minute. The systematic variation of sulfur powder during annealing process has been carried out and their effects on the structural, morphological and optical properties of CTS thin films have been investigated. The preliminary power conversion efficiency of 1.47% with a short circuit current density of $33.9mA/cm^2$, an open circuit voltage of 159.7 mV, and a fill factor of 27% were obtained for CTS thin film annealed with 0.05g of S powder, although the processing parameter s have not yet been optimized.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.171-171
• /
• 2010

GaN 기반 Light emitting diodes(LEDs)의 p-type doping layer는 일반적으로 hole을 발생시키는 acceptor로 Mg이 사용하되고 있다. 보통 Mg이 도핑된 p-type GaN은 >$1\;{\Omega}{\cdot}cm$의 저항이 존재하는데 그 이유는 Mg의 열적 이온화를 위한 activation 에너지가 높아서 상온에서 valence band의 hole concentration는 전체 억셉터 농도의 1%가 되지 않기 ��문이다. 본 논문에서는 높은 hole 농도를 얻기 위해서 metalorganic chemical-vapor deposition (MOCVD)를 장비를 사용하여 사파이어 기판의 misorientation-angle에 따른 p-type a-plane(11-20) GaN 특성을 분석하였다. misorientation-angle은 c축 방향으로 $+0.15^{\circ}$, $-0.15^{\circ}$, $-0.2^{\circ}$, $-0.4^{\circ}$ off된 r-plane(1-102) 사파이어 기판 을 사용하였다. p-type 도핑물질로 bis-magnesium (Cp2Mg) 소스를 사용하였고 성장 과정중 발생하는 hydrogen passivation으로 인한 Mg-H complexes현상을 해결하기위해 conventional furnace annealing (CFA)와 rapid thermal annealing (RTA)를 이용하여 열처리 공정을 진행하였다. 열처리 공정은 Air와 N2 분위기에서 $650^{\circ}C$에서 $900^{\circ}C$ 사이의 다양한 온도에서 수행하였고 Hall 측정을 위해 Ni을 전극 물질로 사용하였다. 상온에서 Accent HL5500IU Hall system을 사용하여 hole concentration, mobility, specific resistance을 측정하였다. 열처리 공정 후 Hall측정 결과 $+0.15^{\circ}$, $-0.15^{\circ}$, $-0.2^{\circ}$, $-0.4^{\circ}$ off된 각 샘플들은 온도, 시간, 분위기에 따라 hole concentration ($7.4{\times}10^{16}cm^{-3}{\sim}6{\times}10^{17}cm^{-3}$), mobility(${\mu}h=\;1.72\;cm^2/V-s\;{\sim}15.2\;cm^2/V-s$), specific resistance(4.971 ohm-cm ~8.924 ohm-cm) 가 변화됨을 확인 할 수 있었다. 또한 광학적 특성을 분석하기 위해 Photoluminescence (PL)을 측정하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.139-139
• /
• 2010

금속 실리사이드 나노입자는 열적 및 화학적 안정성이 뛰어나고, 절연막내에 일함수 차이에 따라 깊은 양자 우물구조가 형성되어 비휘발성 메모리 소자를 제작할 수 있다. 그러나 단일 $SiO_2$ 절연막을 사용하였을 경우 저장된 전하의 정보 저장능력 및 쓰기/지우기 시간을 향상시키는 데 물리적 두께에 따른 제한이 따른다. 본 연구에서는 터널장벽 엔지니어링을 통하여 물리적인 두께는 단일 $SiO_2$ 보다는 두꺼우나 쓰기/지우기 동작을 위하여 인가되는 전기장에 의하여 상대적으로 전자가 느끼는 상대적인 터널 절연막 두께를 감소시키는 방법으로 동작속도를 향상 시킨 $SiO_2/Si_3N_4/SiO_2$ 및 $Si_3N_4/SiO_2/Si_3N_4$ 터널 절연막을 사용한 금속 실리사이드 나노입자 비휘발성 메모리를 제조하였다. 제조방법은 우선 p-type 실리콘 웨이퍼 위에 100 nm 두께로 증착된 Poly-Si 층을 형성 한 이후 소스와 드레인 영역을 리소그래피 방법으로 형성시켜 트랜지스터의 채널을 형성한 이후 그 상부에 $SiO_2/Si_3N_4/SiO_2$ (2 nm/ 2 nm/ 3 nm) 및 $Si_3N_4/SiO_2/Si_3N_4$ (2 nm/ 3 nm/ 3 nm)를 화학적 증기 증착(chemical vapor deposition)방법으로 형성 시킨 이후, direct current magnetron sputtering 방법을 이용하여 2~5 nm 두께의 $WSi_2$ 및 $TiSi_2$ 박막을 증착하였으며, 나노입자 형성을 위하여 rapid thermal annealing(RTA) system을 이용하여 $800{\sim}1000^{\circ}C$에서 질소($N_2$) 분위기로 1~5분 동안 열처리를 하였다. 이후 radio frequency magnetron sputtering을 이용하여 $SiO_2$ control oxide layer를 30 nm로 증착한 후, RTA system을 이용하여 $900^{\circ}C$에서 30초 동안 $N_2$ 분위기에서 후 열처리를 하였다. 마지막으로 thermal evaporator system을 이용하여 Al 전극을 200 nm 증착한 이후 리소그래피와 식각 공정을 통하여 채널 폭/길이 $2{\sim}5{\mu}m$인 비휘발성 메모리 소자를 제작하였다. 제작된 비휘발성 메모리 소자는 HP 4156A semiconductor parameter analyzer와 Agilent 81101A pulse generator를 이용하여 전기적 특성을 확인 하였으며, 측정 온도를 $25^{\circ}C$, $85^{\circ}C$, $125^{\circ}C$로 변화시켜가며 제작된 비휘발성 메모리 소자의 열적 안정성에 관하여 연구하였다.