• Geomechanics and Engineering
• /
• v.6 no.5
• /
• pp.487-502
• /
• 2014

A three dimensional finite element model was used to simulate rapid impact compaction (RIC) in loose granular soils using ABAQUS software for one impact point. The behavior of soil under impact loading was expressed using a cap-plasticity model. Numerical modeling was done for a site in Assalouyeh petrochemical complex in southern Iran to verify the results. In-situ settlements per blow were compared to those in the numerical model. Measurements of improvement by depth were obtained from the in-situ standard penetration, plate loading, and large density tests and were compared with the numerical model results. Contours of the equal relative density clearly showed the efficiency of RIC laterally and at depth. Plastic volumetric strains below the anvil and the effect of RIC set indicated that a set of 10 mm can be considered to be a threshold value for soil improvement using this method. The results showed that RIC strongly improved the soil up to 2 m in depth and commonly influenced the soil up to depths of 4 m.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.10
• /
• pp.5-18
• /
• 2023

The construction timeline for earthworks can be significantly reduced by substituting the conventional layer-by-layer compaction using a vibratory roller with single-layer compaction through the rapid impact compaction (RIC) method. Dynamic load compaction is well-suited for coarse-grained soils like sand. However, as the supply of sand, the primary reclamation material, becomes scarcer, the utilization of soil with fines is on the rise. To implement the dynamic load compaction, such as RIC, with reclaimed materials containing fines, it's imperative to determine the effective improvement depth. In this study, we assess the impact of the RIC method on the effective improvement depth for clean sand and public fill with fines, comparing field test results before and after RIC application. Our focus is on the cone resistance (q_c) as it pertains to compaction quality control criteria. In conclusion, it becomes evident that standardizing the cone resistance is vital for the quality control of various reclaimed soils with fines. We have evaluated the compaction quality control criteria corresponding to a relative density (Dr) of 70% for clean sand as Q_tn,cs = 110. As a result of this analysis, we propose new quality control criteria for q_c, taking into account the fines content of reclaimed soils, which can be applied to RIC quality control.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.4
• /
• pp.64-70
• /
• 2015

A rapid urbanization has increased the portion of paved layer that results in the change of water circulation system. This change leads to frequent events of flooding, drought, and urban heat island. To resolve these issues, permeable pavement system based on Low Impact Development (LID) concept is being applied to international urban areas. Therefore it is necessary to establish a rational design procedure for the permeable pavement system that reflects our environmental conditions. iDue to inherent characteristics of permeable pavement system, water infiltrates thorough the layers so it may reduce the bearing capacity of sub-layers. In this study, an effort was made to investigate the effectiveness of geogrid reinforced crushed stone subbase layer based on field experimental program along with a limited numerical analysis. It reveals that geogrid reinforced sections improve the bearing capacity by close to 20%. In addition, a light weight deflectomenter (LWDT) appears to be promising for the compaction quality control of crushed stone subbase layer in order to construct qualified permeable pavement systems.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.7
• /
• pp.17-30
• /
• 2023

This study investigates the impact of water immersion and high temperature on the shear strength of cemented sand through direct shear tests. Standard Jumunjin sand was used and cemented with binders, such as ultra-rapid hardening cement and an epoxy aqueous solution. The binder was mixed at concentrations of 4%, 8%, or 12%. Subsequently, cylindrical cemented specimens with a diameter of 64 mm and height of 25 mm were produced using compaction. The curing period was three days, and the specimens were cured under dry air, immersion, and heating conditions. The heating condition involved subjecting the immersed specimens to a microwave oven three times for three minutes to achieve an internal temperature of approximately 90℃. Regardless of the binder type, the cohesion of the cemented sand increased with higher binder content, whereas the internal friction angle exhibited a slight increase or decrease. Compared with ultra-rapid hardening cemented sand, epoxy-cemented sand displayed an average cohesion that was five times higher and an internal friction angle that was 10° higher. Overall, irrespective of binder type, the shear strength decreased during water immersion and increased during heating. Notably, the epoxy-cemented sand exhibited a three-fold increase in cohesion and a more than 20° increase in the internal friction angle during heating.