• 한국재료학회지
• /
• 제13권10호
• /
• pp.691-696
• /
• 2003

To improve the photocatalyticactivity of $TiO_2$-coated coal fly ash, tungsten hydroxide was doped by impregnation method and was oxidized by heat treatment in temperature ranges of $WO^{\circ}C$ for 2 hrs. The changes of crystal structure and crystal size of $TiO_2$and $WO_3$on coal fly ash were investigated by X-ray diffraction analysis. The crystal structure of titanium dioxide showed only anatase type and $TiO_2$-$WO_3$ compounds appeared in the heat treatment temperature ranges of $500∼600^{\circ}C$. By adding $V_3$in $TiO_2$coated on fly ash, the growth of crystal size of anatase was restrained and the anatase phase was stabilized in temperature ranges of TEX>$500∼<800^{\circ}C$. And $WO_3$acted as a trap site of electrons excited from anatase by irradiating UV. The maximum removal efficiency of NO gas for $TiO_2$/$WO_3$-coated coal fly ash was 84% and appeared when the ammonium tungstate of $1.3${\times}$10^{-3}$ M was doped and then heated at $600^{\circ}C$ for 2 hrs.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2005년도 총회 및 춘계학술발표회
• /
• pp.271-275
• /
• 2005

The horizontal heat-pulse flowmeter was used to measure grounwater flow in volcanic rocks at sites in eastern part of Jeju Island, Korea. Three boreholes, Handong-1, Jongdal-1, and Susan-1, which are located at close distance from the coastline, were selected from the sea water intrusion monitoring wells. To evaluate the direction and velocity of the groundwater flow, 6 to 8 measuring points for each borehole were chosen. There are two major flow directions at Handong-1, which are toward north-east and south-east directions and velocity ranges from $2.2{\sim}3.0cm/hr\;and\;0.6{\sim}1.0cm/hr$, respectively. For Jongdal-1, two major flow directions were detected that are east and north-west and velocity ranges from $1.2{\sim}2.0cm/hr$. For Susan-1, major flow is toward east direction and the ,velocity ranges from $2.2{\sim}2.7cm/hr$ at depth $60{\sim}70m$,\;and\;0.8{\sim}0.9cm/hr$ at depth $70{\sim}80m$. In order to evaluate the tidal effect on groundwater flow, direction and velocity were measured at specific depth with time, At depth 57m of Susan-1, the velocity increased during the tidal variation, The flow direction and velocity varies with different depths, and they are also affected by tidal fluctuation. Thereafter, care must be taken when flow direction and velociy is estimated indirectly by using hydraulic head at monitoring wells.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제16권6호
• /
• pp.133-142
• /
• 2011

A total of 247 samples were collected from groundwater being used for drinking-water supply, and hydrogeochemistry and radionuclide analysis were performed. In-situ analysis of groundwaters resulted in ranges of $13.7{\sim}25.1^{\circ}C$ for temperature, 5.9~8.5 for pH, 33~591 mV for Eh, $66{\sim}820{\mu}S/cm$ for EC, and 0.2~9.4 mg/L for DO. Major cation and anion concentrations of groundwaters were in ranges of 0.5~227.6 for Na, 1.0~279.3 for Ca, 0.0~9.3 for K, 0.1~100.1 for Mg, 0.0~3.3 for F, 0.9~779.1 for Cl, 0.3~120.4 for $SO_4$, 0.0~27.4 for $NO_3$-N, and 6~372 mg/L for $HCO_3$. Uranium-238 and radon-222 concentrations were detected in ranges of N.D-$131.1{\mu}g/L$ and 18-15,953 pCi/L, respectively. In case of some groundwaters exceeding USEPA MCL level ($30{\mu}g/L$) for uranium concentration, their pH ranged from 6.8 to 8.0 and Eh showed a relatively low value(86~199 mV) compared to other areas. Most groundwaters belonged to Ca-(Na)-$HCO_3$ type, and groundwaters of metamorphic rock exhibited the highest concentration of Na, Mg, Ca, Cl, $NO_3$-N, U, and those of plutonic rock showed the highest concentration of $HCO_3$, and Rn. Uranium and fluoride from granite areas did not show any correlation. However, uranium and bicarbonate displayed a positive relation of some areas in plutonic rocks($R^2$=0.3896).

• 패션비즈니스
• /
• 제17권5호
• /
• pp.151-164
• /
• 2013

This study analyzes the conditions of merchandises from the popular domestic and foreign. In this study, 845 merchandises of 18 popular singers in Korea and 705 merchandises of 20 popular foreign singers are selected. The results of this study are as follows. First, the highest order of merchandise categories among Korean singers are stationeries and toys, followed by fashion accessories, clothes and interior decoration products. For the foreign singers, the highest order of merchandise categories are clothes, followed by fashion accessories, stationeries and toys, and interior decoration products. Second, the most common characteristics of graphic images on the merchandises from Korean singers are characters and expressions of person and body followed by logos, symbols, and gestures of body. Among the foreign singers, the most common characteristics of graphic images are logos, symbols, and gestures of body followed by logos, symbols. Third, by comparing the price ranges between the Korean and foreign merchandises, it is found that foreign singers' merchandises have a more diverse price range than local ones. The highest ordered price ranges among Korean singers are less than 10,000 won, followed by 10,000~20,000 won and 20,000~30,000 won. Among the foreign singers, the highest ordered price ranges are 20,000~30,000 won, followed by 20,000~30,000 won, and 30,000~40,000 won, and less than 10,000 won.

• 한국공간구조학회논문집
• /
• 제18권2호
• /
• pp.59-67
• /
• 2018

Various pilotis are installed in the lower part of high rise buildings. Strong winds can generate sudden airflow around the pilotis, which can cause unexpected internal airflow changes and may cause damage to the exterior of the piloti ceiling. The present study investigates the characteristics of peak wind pressure coefficient for the design of piloti ceiling exteriors by conducting wind pressure tests on high rise buildings equipped with penetration-type and end-type pilotis in urban and suburban areas. The minimum peak wind pressure coefficient for penetration-type piloti ceilings ranges from -2.0 to -3.3. Minimum peak wind pressure coefficient in urban areas was 30% larger than in suburban areas. In end-type piloti ceilings, maximum peak wind-pressure coefficient ranges from 0.5 to 1.9, and minimum peak wind-pressure coefficient ranges from -1.3 to -3.6. With changes in building height, peak wind pressure coefficient decreases as the aspect ratio increases. Peak wind-pressure coefficient increases with taller pilotis. On the other hand, when piloti height decreases, the absolute value of the minimum peak wind pressure coefficient increases.

• 정보과학회 컴퓨팅의 실제 논문지
• /
• 제21권1호
• /
• pp.52-57
• /
• 2015

본 논문에서는 SSD의 TRIM 명령어 처리 성능을 LBA 범위의 특성 및 개수에 따라 분석하고, 그 결과를 바탕으로 Ext4 파일 시스템에서의 TRIM 명령어 처리 성능을 개선하였다. 대부분의 SSD에서 LBA 범위의 크기가 크고, 섹터 번호가 정렬 및 연속되어 있으며, 하나의 TRIM 명령어로 다수의 LBA 범위 정보를 전달할수록 TRIM 명령어의 처리 성능이 증가하는 것으로 나타났다. 한편, 기존의 Ext4 파일 시스템은 이와 같이 다수의 LBA 범위 정보를 전달할 때 그 성능이 더 높음에도 불구하고, 하나의 TRIM 명령어 당 하나의 LBA 범위 정보만 전달하는 문제점을 가지고 있다. 이를 해결하기 위해 하나의 TRIM 명령어로 최대 64개의 LBA 범위 정보를 전달하도록 Ext4 파일 시스템을 개선하였고, Filebench를 이용한 성능 평가에서 파일 삭제 성능이 최대 35% 증가하는 것을 확인하였다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1192-1202
• /
• 1994

Fatigue behavior and life prediction were presented for thermal-mechanical and isothermal low cycle fatigue of 12Cr forged steel used for high temperature applications. In-phase and out-of-phase thermal-mechanical fatigue test at 350 to 600.deg. C and isothermal low cycle fatigue test at 600.deg. C were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. Cyclic softening behavior was observed regardless of thermal-mechanical and isothermal fatigue tests. The phase difference between temperature and strain in thermal-mechanical fatigue resulted in significantly shorter fatigue life for out-of-phase than for in-phase. The difference in fatigue lives was dependent upon the magnitudes of inelastic strain ranges and mean stresses. Increase in inelastic strain range showed a tendency of intergranular cracking and decrease in fatigue life, especially for out-of-phase thermal-mechanical fatigue. Thermal-mechanical fatigue life prediction was made by partitioning the strain ranges of the hysteresis loops and the results of isothermal low cycle fatigue tests which were performed under the combination of slow and fast strain rates. Predicted fatigue lives for out-of-phase using the strain range partitioning method showed an excellent agreement with the actual out-of-phase thermal-mechanical fatigue lives within a factor of 1.5. Conventional strain range partitioning method exhibited a poor accuracy in the prediction of in-phase thermal-mechanical fatigue lives, which was quite improved conservatively by a proposed strain range partitioning method.

• 한국운동역학회지
• /
• 제17권1호
• /
• pp.1-8
• /
• 2007

Ground reaction force (GRF) measures are one of the most commonly used in biomechanical study. GRF system is very useful educational tool to explain and demonstrate the Newton's law of universal gravitation and laws of motion as well. However, accuracy, intra- and inter- force platform measures' consistency, reliability, noise, and the effect of platform mounting to GRF measures were not clearly viewed. The aim of this study was to examine the above. GRFs of a plastic dummy and two subjects' quiet upright standing were collected at four university laboratories eight force platforms. The types of platforms, analysis programs, and platform set-up were various. Three 100s-trials were conducted with sampling frequency of 100 Hz. First two trials' vertical component of GRFs, Fz, and CoP sway ranges of mid-60s-portion of 100s trials were analyzed by the paired t-tests and one-way ANOVA. Six of eight platforms' 1st and 2nd trial dummy Fz were statistically different (p<.05) and all platforms ICC were poor (<.28). Fz of the two platforms in every four laboratories were statistically different (p<.05). There were white noises and/or very distinctive noises at specific frequency ranges in all Fz measures. 5 Hz low-pass filtering made clear the Fz differences. CoP ranges of dummy were less than 0.5 cm and the best was 0.02 cm. This CoP range finding agrees with previous results suggests the importance of force platform mounting and A/D card resolution.

• 한국군사과학기술학회지
• /
• 제12권1호
• /
• pp.123-132
• /
• 2009

Civil petitions and law suits against the military rifle shooting noise have been increased because many military shooting ranges are located near civilian residential area. In order to solve the noise problems, military have devised various methods. In this study, propagation properties of rifle shot through atmosphere were investigated. The military rifle shooting noise level at 5m from muzzle was between $l14{\sim}120dB$ in all directions. The noise level loom both backward and sideward away from system firing range consisting lines of 8 shooting locations were 90dB, when shots were all fired within 10 seconds. At present some of military bases established sound barriers, muzzle enclosures, silencers, and indoor shooting ranges to reduce noises and these prevention methods can reduce noise by $5{\sim}20dB,\;5{\sim}9dB,\;5{\sim}13dB,\;40{\sim}50dB$, respectively. Even though indoor shooting range has the best performance, it requires very expensive construction cost and has short length between target and shooter. In comparison, muzzle enclosure is cheap, but because it is installed in fixed position it can only be used in one shooting position. Therefore a commander should select appropriate methods to reduce military rifle shooting noise considering distance from residential area to the range, mission of military training, budget, etc.

• 대한안전경영과학회지
• /
• 제16권2호
• /
• pp.43-52
• /
• 2014

In weapon systems development, live fire tests have been frequently adopted to evaluate the performance of the systems under development. Therefore, it is necessary to ensure safety in the test ranges where the live fire tests can cause serious hazards. During the tests, a special care must be taken to protect the test and evaluation (T&E) personnel and also test assets from potential danger and hazards. Thus, the development and management of the range safety process is quite important in the tests of guided missiles and artillery considering the explosive power of the destruction. Note also that with a newly evolving era of weapon systems such as laser, EMP and non-lethal weapons, the test procedure for such systems is very complex. Therefore, keeping the safety level in the test ranges is getting more difficult due to the increased unpredictability for unknown hazards. The objective of this paper is to study on how to enhance the safety in the test ranges. To do so, an approach is proposed based on model-based systems engineering (MBSE). Specifically, a functional architecture is derived utilizing the MBSE method for the design of the range safety process under the condition that the derived architecture must satisfy both the complex test situation and the safety requirements. The architecture developed in the paper has also been investigated by simulation using a computer-aided systems engineering tool. The systematic application of this study in weapon live tests is expected to reduce unexpected hazards and test design time. Our approach is intended to be a trial to get closer to the recent theme in T&E community, "Testing at the speed of stakeholder's need and rapid requirement for rapid acquisition."