• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.2
• /
• pp.62-68
• /
• 2007

This paper proposes an efficient integer division algorithm for high speed FPGAs' which support built-in RAMs' and multipliers. The integer division algorithm is iterative with RAM-based LUT and multipliers, which minimizes the usage of logic fabric and connection resources. Compared with some popular division algorithms such as division by subtraction or division by multiply-subtraction, the number of iteration is much smaller, so that very low latency can be achieved with pipelined implementations. We have implemented our algorithm in the Xilinx virtex-4 FPGA with VHDL coding and have achieved 300MSPS data rate in 17bit integer division. The algorithm used less than 1/6 of logic slices, 1/4 of the built-in multiply-accumulation units, and 1/3 of the latencies compared with other popular algorithms.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.70-77
• /
• 2015

This paper develops and evaluates a mechanical machining process which involves drilling on PVS material. According to the material, two treatment experiments were conducted, one involving drilling in a wet condition or using a lubricant and one involving drilling in a dry condition with no lubricant. Drilling in a dry condition showed better performance in terms of the cutting time than in the wet condition. Otherwise, the wet condition has several advantages. The lubricant influenced the burr diameter size and minimized the temperature on the surface of the work piece. During the wet condition drilling process, a smaller burr diameter size was noted as compared to the dry condition. The temperature showed a linear correlation with the drill bit size, where a least-square analysis provided an $R^2$valuewhichexceeded 0.95. The wet condition required more cutting time than the dry condition. In this condition, the water provides a lubrication effect. A thin layer between the cutting edges and the surface of the work piece is formed. The chip formation is affected by the drilling depth. The color on the tips of the chips was darker than in the initial condition. No correlation between the drilling depth and the bore roughness was noted, but the variation of the cutting speed or the RPM influenced the roughness of the bore. The optimum cutting speed ranged from 40 RPM to 45 RPM in the condition which provided the finest roughness surface.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.163-170
• /
• 2010

We have studied on welding dissimilar materials of cold-reduced carbon steel sheet and stainless steel sheet together by using laser beam. It is well known that stainless steel is so strong againt rust and heat, while cold-reduced carbon steel is widely used in various parts of industry. In this research we have performed some experiments to know the possibility of welding dissimilar materials using laser beam by adjusting the power output of 3kW laser. Other conditions of the experiments were as follows : the welding speed was varied in the range between 2m/min and 7m/min, argon gas and helium gas were used as shield gas, the flow value of shield gas was ranged between $10{\ell}/min$ and $30{\ell}/min$, and the gap of two materials was ranged between 0mm and 0.3mm. In order to ascertain of the welded surface, we have done the tensile strength testing, the hardness testing and the microscope observation. As a result, we have found that tensile strength was the highest at the condition of the welding speed of 4, the flow value of $20{\ell}/min$, the gap of two materials 0, and the use of helium gas. Above testings have also showed that the tensile strength was generally satisfactory since the penetration of welding was almost complete due to the thinness of the materials. In addition, the formation of the welded area was excellent when it had the highest tensile strength.

• Resources Recycling
• /
• v.23 no.5
• /
• pp.36-43
• /
• 2014

It comtained various kinds of heavy metal in beneficiatian tailing and in order to eliminate the heavy metals, various technologies have been researched, But there are a limits because many problems and restrictions are accompanied. Therefore, in this study, in order to solve this problem, It was performed gravity separation using melti-gravity seperator (MGS) to remove As contained in tailing, which can sort out even the fine particle. It was attempted a study to remove As, which is a kind of heavy metals, by MGS gravity separation and verified the impact by slope, wash water, pulp density, rotational speed and feed rate. In the results of performing gravity concentration under the condition with the MGS slope of $3^{\circ}$, wash water of 5 l/mm, pulp density of 30%, rotational speed of 208 rpm, and the feed rate of 265.24 g/mm, the As removal rate of 88.21% and yield of 92.25% were obtained.

• Journal of Navigation and Port Research
• /
• v.46 no.3
• /
• pp.243-250
• /
• 2022

The purpose of this study was to propose technology to detect the wave in the image in real-time, and calculate the height of the wave-overtopping through image analysis using artificial intelligence. It was confirmed that the proposed wave overtopping detection system proposed in this study could detect the occurring of wave overtopping, even in severe weather and at night in real-time. In particular, a filtering algorithm for determining if the wave overtopping event was used, to improve the accuracy of detecting the occurrence of wave overtopping, based on a convolutional neural networks to catch the wave overtopping in CCTV images in real-time. As a result, the accuracy of the wave overtopping detection through AP50 was reviewed as 59.6%, and the speed of the overtaking detection model was 70fps based on GPU, confirming that accuracy and speed are suitable for real-time wave overtopping detection.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.405-408
• /
• 2007

Semi-solid Al-Zn-Mg alloys were produced using a cooling plate method in order to investigate the extrudability. Al melt was poured on cooling plate which was adjusted at $60^{\circ}$ with respect to the horizontal plane, and the melt was cooled by water circulation underneath. Obtained Semi-solid feedstock has globular microstructure but also contains considerable amount of gas pore. Due to the pore, tensile elongation of the semi-solid feedstock was very low and it doesn't show yield point phenomenon. Isothermal hot extrusion was carried out using at $400^{\circ}C$ with a ram speed of 1mm/sec and an extrusion ratio of 25:1. The extruded bar show noticeably improved tensile ductility and strength because pore volume fraction decreased from 5% to 0.8% after extrusion. Mechanical properties of the semi-solid extruded bar were compared with that of commercial casting alloy..

• Transactions of Materials Processing
• /
• v.28 no.6
• /
• pp.347-353
• /
• 2019

The porthole extrusion process is a classic metal forming process to produce complex cross-section shaped aluminum profile. It is very difficult to design porthole die and extrusion process because of the complex shape of extrusion die and internal metal flow. The main variables in this process are ram speed, initial billet and tool temperature, and die shape. In general, the metal flow of porthole extrusion process can be divided into two steps. During the first step, the billet is divided into several parts in the porthole die bridge. During the second step, the divided billets are welded in the welding chamber. In the welding chamber, the level of welding pressure is very important for the quality of the final product. The purpose of this study is to increase the welding pressure in the welding chamber by using a two stage welding chamber. The porthole extrusion die was designed by using the Taguchi method with orthogonal array. The effectiveness of the optimized porthole die was verified by using the finite element analysis.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.285-288
• /
• 2001

Hypereutectic Al-25Si-X alloys, expected to be applied to the cylinder-liner-part of the engine-block of an automobile due to the excellent wear resistance, low density and low thermal expansion coefficient has been fabricated through a spray forming process. The obtained microstructure of the hypereutectic Al-25Si-X alloy appeared to consist of Al matrix and equiaxed Si particles of average diameter of $5-7{\mu}m$. To characterize the deformation behavior of this alloy, a series of load relaxation and compression tests have been conducted at temperatures ranging from RT to $500^{\circ}C$. The strain rate sensitivity parameter (m) of this alloy has been found to be very low (0.1) below foot and reached 0.2 at $500^{\circ}C$. During the deformation above 300'c in compression, strain softening has been observed. The diagram of extrusion pressure vs. ram-speed has been constructed, providing the extrusion condition of Al-25Si-X alloys.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.644-650
• /
• 2012

This paper show the 2kW fiber laser cutting properties of SS400. The study was comparison of traditional 4kW $CO_2$ Laser cutting and 2kW Fiber laser cutting characteristics for the application of Industrial 2D Laser Cutting Machine. The laser used in this investigation was an IPG YLU-2000 multi-mode Ytterbium Fiber machine with a maximum power of 2000W and a wave length of 1070 nm. The laser was used in its Continuous Wave (CW) mode with an approximately top hat beam intensity distribution. Fiber laser high quality cuts at a large range of speeds (ranging from 2000 to 3800 mm/min) which has been obtained for the 2.3mm Sheet of SS400. 2kW power Fiber laser cut was able to max. 20mm sheets of SS400 (speed range from 650 to 850 mm/min). Fiber laser cutting used in conventional hole nozzle could cut 12mm SS400 but used in special dual cutting nozzle could cut 20mm SS400.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.4
• /
• pp.395-408
• /
• 2012

An experimental investigation with 2.8kW Nd:YAG laser system was carried out to study the effects of different laser process parameters on the microstructure and hardness of STD11. The optical lens with the elliptical profile are designed to obtain a wide surface hardening area with uniform hardness. The Laser beam is allowed to scan on the surface of the work piece varying the power (1600, 1800 and 1900kW) and traverse speed (200, 400, 600, 800 and 1000mm/min) at three different F-numbers of lens. After laser surface treatment three zones, In the microstructure have been observed : melted zone(decarburization), heat affected zone(martensite), and the substrate.