• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.8
• /
• pp.3610-3616
• /
• 2011

Electrical Railroads provide electric power, which can operate vehicles, via feeder wires. And the supplied current returns to the transformer substation through lines and ground net. The used load current depending on the operation of rail vehicles in the electric railway sections returns to the substation through a track which is a return circuit. The load current contains harmonics because of the power conversion equipment used in rolling stocks and such harmonic currents should not affect train control system. In this paper we present the test result in order to verify that the harmonics produced by the operation of rail vehicles in the newly built electric railway sections can affect interlocking systems. The test in question was performed in a linking section that trackside equipment under railway operating conditions and interlocking are linked in order to identify whether or not the interlocking fitted in a signal machine room can be affected by harmonics according to railway operation.

• Journal of the Korean Society for Railway
• /
• v.15 no.5
• /
• pp.454-458
• /
• 2012

The CBTC(Communication based Train Control) and WPAN(Wireless Personal Area Network) systems employed on 2.4GHz ISM band wireless networks provide complementary service within the same environment. Coexistence between the networks will be impaired if the mutual packets are uncertainty associated the timing or gaussian distance. This paper analyzes the impact of the mutual interference and proposed method to minimize the effect of the WPAN system signals on CBTC system. The performance analysis is illustrated by examining the symbol error rate versus signal to noise interference ratio in terms of carrier frequency offset. The method contributes to reduce the symbol error rate drastically. However it can't be a fundamental solution for the impact on the interference problem. It may be needed for railway only frequency after checking the problems of the current railway frequency.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1680-1684
• /
• 2010

CBTC(Communication-Based Train Control) system which is based on wireless communication can provide high density operation of the train using location tracking between ground and onboard train. It can also reduces maintenance expense because it does not require the ground equipment for tracking circuit and signal flag and so on. Recently, research and interest have been done on CBTC system. The high-speed trains up to 300km/h experience multi-path fading channel which bring about the performance degradation of wireless CBTC system. In this paper, we consider MIMO (Multi-Input Multi-Output) antenna-based CBTC system for trains with Alamoutip-type space-time diversity transmission for reliable communication. Also we model a channel considering practical environment and evaluate performance improvement of proposed CBTC system.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.270-277
• /
• 2009

This paper describes the method of how to improve the probability of the tracing stopping ratio which is the most important factor in Automatic Train Operation (ATO). Aspects of improving the performance of automatic driving, the followings are investigated and studied : the interface between the signal system and the vehicle, the need to improve braking system, test method of blending brakes, how to minimize the delay of commands for real-time control. In this study, we applied this method to prove the effectiveness in DAEJEON LINE1

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1480-1485
• /
• 2004

In this paper, a real-time digital kalman filtering algorithm is used to obtain the reference estimation of the control current for shunt active power filter. This algorithm provides the best estimate of the fundamental and harmonic frequency components from the sampled values of the line current or voltage waveform. By adopting of the digital Kalman filtering algorithm, the structure of the control algorithm eliminates the need of a Phase locked loop(PLL) for the synchronization of the reference signal used in the compensation and it not sensitive to the distortion of the line voltage. The effectiveness of the algorithm is confirmed by the computer simulations.

• Journal of the Korean Society for Railway
• /
• v.11 no.5
• /
• pp.477-481
• /
• 2008

This paper dealt with a detection method of series arc existence which is a symptom of electric fires in low-voltage system. The proposed detection circuit consists of a high-pass filter with a low cut-off frequency of 3kHz to attenuate power frequency voltage by 80 dB and an active band-pass filter with a center frequency of 4kHz to detect only the series arc signals. The performance of the circuit was evaluated in a phase-controlled incandescent lamp as a non-linear load and an inverted-fed induction motor as a high frequency load by using the arc generator specified in UL1699. From the experimental results, it was confirmed that the proposed method solved the detection error, which is being the most problem, by discriminating the series arc signal even in non-linear and high frequency loads.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.339-342
• /
• 2008

In this paper, the lessons and learns are introduced from the result of the trial project which is the first CBTC(Communication Based Train Control System) at Korail Bundang Line. This project has started end of 2002 and finished recently by Samsung SDS. The main purpose of this project was that new technology was seek for next generation of railway signal control system adapted in Korea. In 2002, there was no any revenue service system using Radio Frequency CBTC in the world at that time. Just a few trial project was on going in USA and EU. In well developed cities, the metro system have been built and old enough therefore they have to be considering re-signalling their existing system with advanced system for increasing availabilities of line usage and safety. This Bundang Line Trial Project was the first Korean CBTC project for above reasons. Most sub systems have been developed using local technology such as Electronics Controlled Interlocking System and Track Circuit Systems etc. Specially, in this project the RF-Communication devices are developed by local technology using DSSS(Direct Sequency Spread Spectrum) instead of FHSS(Frequency Hopping Spread Spectrum). This project has lasted for more than five years originally planned for three years because it was only accessible only night time in the main line from Ori to Suseo about 20km long. Each night only 2 and half hours are available to use the main line. Now the trial project has been done successfully with meet the customer's requirement, therefore the upgrade the mainline of Bundang line and another extension area up to Wangsipli to make revenue service using this new technology. This paper shows this result of the trial project and the strategy of upgrade and extension project as well.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8187-8194
• /
• 2015

To accelerate a heavy roller coaster train with over 1G force, a lot of thrust is required and linear synchronous motor(LSM) as propulsion method is suitable for this kind of system. To increase the propulsion efficiency of LSM, precise and real-time position information of vehicle is required for accurate phase control. However, the discontinuous position information with relatively long time interval is usually transmitted from the hall-sensors on the track every magnet length. In this paper, the basic motor model based on traditional dq-axis equations is described and the motor dynamic model is produced by considering the cogging force and friction loss. To improve the position accuracy, the position estimator is also proposed for LSM control system. Simulations were performed to check the characteristics of the torque control system which includes the position estimator based on the motor model. Simulation results based on the linearized model show that this control system has an enough bandwidth and phase margin and the executed algorithm achieves an ideal effect to follow the real-time position signal. Therefore, the feasibility of position estimator is also confirmed.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1838-1844
• /
• 2011

In this paper, the propulsion control of a high-speed maglev train is studied. Electromagnetic suspension is used to levitate the vehicle, and linear synchronous motors (LSM) are used for propulsion. In general, a low-speed maglev train uses a linear induction motor (LIM) for propulsion that is operated under 300[km/h] due to the power-collecting and end-effect problem of LIM. In case of the high-speed maglev train over 500[km/h], a linear synchronous motor (LSM) is more suitable than LIM because of a high-efficiency and high-output properties. An optical barcode positioning system is used to obtain the absolute position of the vehicle due to its wide working distance and ease of installation. However, because the vehicle is working completely contactless, the position measured on the vehicle has to be transmitted to the ground for propulsion control via wireless communication. For this purpose, Bluetooth is used and communication hardware is designed. A propulsion controller using a digital signal processor (DSP) in the ground receives the delayed position information, calculates the required currents, and controls the stator currents through inverters. The performance of the implemented propulsion control is analyzed with a small maglev train which was manufactured for experiments, and the applicability of the high-speed maglev train will be explored.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1136-1139
• /
• 2000

The paper describes a new and rigorous mathematical model for the rotor field oriented system with induction motor which uses the estimated speed and rotor flux based on a Model Reference Adaptive System, as well as the real-time approach. The estimated speed and rotor flux is used for the speed and flux feedback control. The stability and the convergence of the estimator are improved on the basis of hyperstability theory for non-linear systems. The real-time controller and estimator are implemented with a sampling period of $926{\mu}s$ using a dual TMS320C44 floating-point digital signal processor. The validity of the proposed method is verified by simulation, and also, the sensorless control was tested on the propulsion system simulator, used for the development of Korean High-Speed Railway Train (KHSRT) [5].