• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.19-26
• /
• 2013

Cu-matrix sintered brake pads and low-alloy heat-resistant steel are commonly applied to basic brake systems in high-energy moving machines. In this research, we analyzed the tribological characteristics to determine the influence of the air velocity between the disk and pad. At a low brake pressure with airflow, the friction stability was decreased as a result of the lack of tribofilm formation at the disk surface. However, there were no significant changes in the friction coefficient under any of the test conditions. The wear rates of the friction materials were decreased with an increase in the airflow velocity. As a result, the airflow velocity influenced the friction stability, as well as the wear rate of the friction materials and disk, but not the friction coefficient.

• Tribology and Lubricants
• /
• 제29권2호
• /
• pp.98-104
• /
• 2013

Cu-matrix-sintered brake pads and heat-resistant low-alloy steel are commonly applied to basic brake systems in high-energy moving machines. We analyzed how the tribological characteristics are influenced by the inertial mass. A high inertial mass decreased the friction coefficient by about 15% compared to a low inertial mass under all velocity conditions. The wear rates of the friction materials increased with the inertial mass. Thus, the inertial mass influences the friction coefficient and wear rate of the friction materials and disk but not the friction stability.

• 전기전자학회논문지
• /
• 제22권2호
• /
• pp.480-483
• /
• 2018

Wireless power transfer (WPT) is the technology that forces the power to transmit electromagnetic field to an electrical load through an air gap without interconnecting wires. This technology is widely used for the applications from low power smartphone to high power electric railroad. In this paper, the model of wireless power transfer circuit for the low power system is designed for a resonant frequency of 13.45 MHz. Also, a feedback WPT circuit to improve the power transfer efficiency is proposed and shown better performance than the original open WPT circuit, and the methodology for power efficiency improvement is studied as the coupling coefficient increases above 0.01, at which the split frequency is made.

• 한국터널지하공간학회 논문집
• /
• 제17권6호
• /
• pp.615-621
• /
• 2015

In this paper diamond wire cutting method has been proposed to cut the rock in the tunnel face. Diamond wire saw method could cut the rock from tunnel face with very minor vibration and noise. In this study rock cutting process has been simulated with FEM method by using LS-DYNA explicit non-linear finite element code. Normal load act as an prime factor when cutting the rock surface. For observing the effect of normal load on bead, several experiments has been conducted by varying normal loads on the bead. From each experiment, cutting rate has been calculated to compare the cutting rate with different load conditions. By increasing the normal load on bead, cutting rate increases drastically.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 추계학술대회 논문집
• /
• pp.62-73
• /
• 2001

The scope of this study is focused on the survey of new logistics transportation systems in railroad and case studies of new systems such as piggyback system, bi-modal system swapbody, and double stack train(DST). Piggyback system, bi-modal system, swapbody, and double stack train are reviewed in term of technological validity and economic validity in Korea. Piggyback - trailer does pass loaded weight limits but does not pass train limits and can not utilize the existing freight cars. Piggyback - cargo trunk does pass all the criteria and could be developed by a domestic technology. But this study suggests to expand the length of train cars to 18.300mm for accommodation of two cargo trucks. Bi-modal system and swapbody do also pass. Double stack train could only pass the loaded weights and does not meet the train limit and the possibility of using existing freight cars. Domestic technology could not development DST, due to civil engineering construction limits and low standard height of electric line, which could not afford to operate DST.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1250-1252
• /
• 2007

Recently, a large amount of waste has been occurred from electric motor units (EMUs) due to the excess of their duration or the exchange of interior. In Korea, most of waste has been treated by incineration or landfill because the special treatment system of disused EMUs has not been existed until now. The objective of this study is to investigate the international railroad cases for the efficient treatment of disused EMUs. Japanese railroad makes an effort to enhance the recycling efficiency of rolling stocks such as the use of recycling materials or the development of recycling technology. Also, Europe has decided to treat the disused rolling stocks considering the inspection of their conditions and the increase of management cost. Therefore, in the future, it will be necessary to improve the domestic regulations related to the duration of rolling stocks and to develop the recycling technology of interior preferentially.

• 센서학회지
• /
• 제14권6호
• /
• pp.438-443
• /
• 2005

In this paper, we introduce the on-line test of the current collection characteristics for HSR 350x(Korea High Speed Train project) that have been performed in the Kyoung-bu high-speed line since 2002. Through the analysis of measured data during on-line test, the variation trends of contact force between pantograph and catenary according to the track conditions and driving patterns are reviewed. This study shows that the track conditions do not affect on the dynamic performance between pantograph and the driving patterns are important factors in determining the good interaction of them.

• Tribology and Lubricants
• /
• 제29권4호
• /
• pp.242-247
• /
• 2013

This study aims to establish the fundamental basis for the design of materials used in high-speed trains, by using a lab-scale dynamometer to evaluate the characteristic behavior of metallic sintered friction materials in relation to the shape of graphite. The test results clearly demonstrate that when flake graphite and granular graphite are added equivalently, the average coefficient of friction is much lower, and it is less influenced by speed variation; moreover, friction wear is observed to be insignificantly low. Adding flake graphite increases the coefficient of friction, which leads to higher friction wear. In addition, the roughness of the disc surface was equivalent regardless of the shape of the graphite.

• 한국생산제조학회지
• /
• 제25권5호
• /
• pp.380-385
• /
• 2016

Railway tracks are repeatedly overstressed and damaged owing to increase in passing tonnage and numerous contact cycles between wheels of train and rails. In order to ensure safe train operation, heat-treated rails are used in addition to regular inspection and maintenance of these rails. Normal rails were treated using ultrasonic nanocrystal surface modification (UNSM) to strengthen the surface of rails. A few changes in surface properties were detected with respect to hardness and compressive residual stress after UNSM treatment. Wear and rolling contact fatigue tests were performed using rails whose surfaces were hardened by UNSM and heat-treated rails. The amount of wear and fatigue life cycles were measured to estimate the effect of UNSM on the rail material. The material of the surfacehardened rail showed improved wear and rolling contact fatigue properties.

• 산업공학
• /
• 제20권1호
• /
• pp.21-32
• /
• 2007

This paper deals with the simulation model for A-Mart logistic center design and operations. In developed simulation model, receiving docks, conveyor sorter, conveyor system, shipping docks, material handling devices and manual sorting stations are considered. Three types of cargo such as transfer center cargo, distribution center cargo and supermarket cargo are considered. The simulation model and process animation are developed using the simulation package ARENA. Among various design and operation alternatives consisting of the number of workers of receiving dock, allocation of receiving docks by cargo types, conveyor sorter velocity, the number of folk-lift, the number of manual sorting operators and overall layout, the best alternatives of each subsystem are selected by simulation analysis. The major performance measures such as sorter throughput, utilization of operators at each station, receiving docks utilization and folk-lift utilization are considered for the alternative evaluation.