• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.25 no.1
• /
• pp.137-155
• /
• 1999

The o/w emulsions were prepared by lysolecithin as a biosurfactantsto to emulsify oils with squalane(SQ), liquid paraffin(LP), octylpalmitate(OP), octylstearate(OS), alkyl benzoate(AB), isostearyl benzoate(ISB). The droplets size and shape of o/w emulsions were investigated by laser light scattering, With dynamic light scattering hydrodynamic radius(Rh) of emulsion droplets was varied from 150m to 250m and critical concentration of oil In which the hydrodynamic radius(Rh) of emulsion droplets decreased and increased was found in the point of 0.5wt% oil concentration, and it was found increasing the polarity of oil deccreased the droplets, the droplets size of SQ(polar oil) were lower than SQ(nonpolar oil) With static light scattering radius of gyration(R$_{g}$) of emulusion droplets was to be calculated. From measurements of the ratio of R$_{g}$R$_{h}$ it was found that the shape of droplet of ISB, AB(polar oils) were sphere, for OP, OS(apolar oil) were oblate, for LP, SQ(nonpolar oil) were rod. The viscosity of emulsion in the form of rod was higher than that of emulsion in the form of sphere.e.e.

• Journal of Mechanical Science and Technology
• /
• v.16 no.6
• /
• pp.785-798
• /
• 2002

A reliable analytic model that predicts the surface profile of the exit cross section of workpiece in round-oval (or oval-round) pass sequence is established. The presented model does not require any plasticity theory but needs the only geometric information on workpiece and roll groove. Formulation is based on the linear interpolation of the radius of curvature of an incoming workpiece and that of roll groove in the roll axis direction when the maximum spread of workpiece is known beforehand. The validity of the analytic model is examined by hot rod rolling experiment with the roll gap, specimen size, design parameter of oval groove and steel grade changed. Results revealed that the cross sectional shapes predicted by the model were in good agreement with those obtained experimentally. We found that the analytic model not only has simplicity and accuracy for practical usage but also saves a large amount of computational time in comparison with finite element method.

• The Journal of the Korean bone and joint tumor society
• /
• v.10 no.1
• /
• pp.29-33
• /
• 2004

A giant cell tumor (GCT) of the distal radius is not common. Curettage with bone cementation is considered as a treatment of choice but, in the case of recurrence, marked cortical disruption, or articular invasion, en bloc excision and reconstruction with proximal fibular bone graft is usual procedure. In reconstruction of en bloc resected distal radius which had recurred GCT after conservative operation, we used the ultrahigh molecular weight polyethylene (UHMWPE) liner with intramedullary rod and bone cement, because the contamination was extent in previous operation and recurrence after fibular bone graft was fearful. This article introduce our new surgical procedure.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.1
• /
• pp.71-76
• /
• 2006

The electrical characteristics of concrete block including a reinforcing rod in the foundation of the housing was fundamentally reviewed. It was tried to apply the substitutional earthing electrode in the foundation of the building. In order to identify the difference in the earthing resistance between mortar block and concrete block model, those models including a reinforcing rod in their inside were prepared and investigated for the earthing resistance. In results, the earthing resistance was largely affected by the block's resistivity compared to the change of resistance in reinforcing rods and the ground resistivity.

• Current Optics and Photonics
• /
• v.4 no.5
• /
• pp.441-445
• /
• 2020

A novel design for a Fresnel lens for a solar end-pumped laser is demonstrated in this paper. The new hybrid Fresnel lens includes two parts, inner and outer. The inner part is a twice-total-internal-reflection and vertical-transmission lens. The outer part is a once-total-reflection and vertical-transmission lens. The radius of the Fresnel lens is 600 mm, and its focal length is 750 mm. The concentrating performance of the Fresnel lens is examined using TracePro. The results show that the concentration efficiency has been greatly improved. The total concentration efficiency of the hybrid Fresnel lens reaches 73.2% when the radius of the laser rod is 3 mm. This design can simplify the concentration system of a solar end-pumped solid-state laser.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.7
• /
• pp.545-553
• /
• 2003

This paper is concerned with protecting piezoelectric transducers used in an ultrasonic flowmeter from the high temperature of hot fluid in a pipe by using a waveguide and with improving the propagation of ultrasonic longitudinal vibration in the waveguide. Waveguide material has been chosen for efficient insulation of heat transferred in the waveguide, and the minimum length of the waveguide for protecting piezoelectric transducer has been estimated. Forced response of the longitudinal vibration in a uniform circular rod has been obtained and the length of the waveguide has been selected for maximum amplitude. Longitudinal vibration response of a conically-tapered rod excited at a natural frequency has been obtained to confirm that wave motion is amplified as the cross-sectional size of the waveguide decreases along the axial direction. The fact that dispersion of a pulse wave in a waveguide is reduced as the cross-sectional radius is decreased has been examined theoretically and confirmed experimentally by using a single-rod waveguide. A bundle-type waveguide has proven to be a practical one through the evaluation of the wave propagation performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.43-53
• /
• 1998

This paper addresses an optimization for reducing a steering error of a rack-and-pinion steering linkage with a MacPherson strut independent front suspension system. The length, orientations and inner joint positions of a tie-rod are selected as design variables and Ackerman geonetry, understeer effect, minimum turn radius, wheel alignment and packaging are considered as design constraints. Nonlinear kinematic analysis of the steering system is performed for calculating the values of cost and constraints, and Augmented Lagrange Multiplier(ALM) method is used for solving the constrained optinization problem. The optimization results show that the steering error are considerably reduced while satisfying all the constraints.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.78-87
• /
• 1999

A mathematical model for the stress free surface profile in Over-Round and Round-Oval grove rolling, which can be used effectively in the calculation of pass area, is presented. The new model has generality, simplicity and accuracy for practical usage. The stress free surface profile of an outgoing stock can be modeled when the maximum spread of it known a priori. The equation for the stress free surface profile is formulated from the linear interpolation of the radius of curvature of an incoming stock and that of roll groove to the axis direction. In developing the analytical model, the effect of rolling temperature and friction between roll and work piece(stock) were not considered since the geometry of roll groove and the incoming work piece were assumed a dominant factor which decides the stress free surface profile of the outgoing stock. A simulation with the analytical model developed also has been carried out to demonstrate the stress free surface profile of the outgoing stock.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.2
• /
• pp.23-29
• /
• 2008

This study analyzes the rolled circular rod strip with radius of loom and length of 350cm by using finite element analysis. The material strength and its durability of the rolled strip can be predicted through this study. As the penetration tolerance by contact decreases, the contact rigidity of strip increases. As the contact rigidity becomes the highest at the elapsed time of 1.2 second, the contact stress becomes the lowest. On the contrary, von-Mises stress becomes highest at this time. The total deformation on strip increases from the upper part of strip at the position near to rotating roll to the lower part of strip at the position near to fixing roll.

• Journal of the Korean Physical Society
• /
• v.73 no.10
• /
• pp.1410-1419
• /
• 2018

A skier's motion was analyzed by a simple model consist of point mass m and a single rod connected to a single ski plate. We studied the conditions for the stable ski turn as functions of the linear velocity and the radius of the turn. The solutions for the stable ski turn in our model do not require any extra skier's movement to complete a stable circular turn. The solution may then give the skier the most comfortable skiing method without any active movement to control the ski. The generalized force supporting the point mass from the ski plate was calculated. We obtained the force from the ground (rebound force) without any geometrical structure of the ski plate. Adding an active movement to the direction of the ski plate, the conditions for the stable ski turn were also analyzed. Our result gives some insight for the skier who wants to develop technique.