• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1680-1683
• /
• 2003

To describe the performance of an antenna, some parameters are necessary. Some of the parameters are interrelate and not all of them must be specified for complete description of antenna performance. The parameters in characteristics of printed antenna for this analysis are radiation pattern, input impedance, VSWR, S parameter and electromagnetic field. In this paper we will consider two shaped of slot antennas one is triangular slot antenna and other is L - shape slot antenna for compare the radiation pattern, return loss, and VSWR. Two slot antennas are designed to have a resonant frequency at 10 GHz. The microstrip line is designed to be 50 ohms in order to match the measurement system, it has the substrate of the thickness = 1.52 mm and dielectric constant (${\varepsilon}_r$) 2.17. The problem space in the FDTD analysis are $60{\times}123{\times}100$ cells for L-shape slot antenna and $50{\times}171{\times}120$ cells for triangular slot antenna with the cell dimensions ${\Delta}x=0.152\;mm.$, ${\Delta}y={\Delta}z=0.15\;mm.$

• Journal of Radiation Industry
• /
• v.9 no.3
• /
• pp.131-135
• /
• 2015

The flow characteristics of fluid were measured using radioactive tracer in pilot scale digester with tray motion mixer. In consideration of the detection volume of the detector and the size of the digester, 20 detectors were installed in the digester. The radioactive tracer eluted 8 mCi of $^{68}Ga$ from $^{68}Ge/^{68}Ga$ generator was injected into the digester bottom. After radiotracer injection, the flow pattern was measured on the basis of the initial movement of the tracer until its diffusion completely. Most of tracer moved to the wall along the bottom of the digester, and then rose along the wall. The other tracer moved up along the mixer, and then moved to the wall direction along the surface.

• Korean Journal of Digital Imaging in Medicine
• /
• v.11 no.2
• /
• pp.115-119
• /
• 2009

I think this will be valuable reference for assuring consistency and homogeneity of clarity and managing dental radiation equipment by experimentation of dental radiation equipment permanent which based on KS C IEC 61223-3-4 standard and KS C IEC 61223-2-7. Put a dental radiation generator and experiment equipment as source and film(sensor) length within 30 em, place the step-wedge above the film(sensor). Tie up tube voltage 60 kVp, tube current 7 mA and then get an each image through CCD sensor and film by changing the exposure time as 0.12sec, 0.25sec, 0.4sec. Repeat the test 5times as a same method. Measure the concentration of each stage of film image, which gained by experiment, using photometer. And the image that gained by CCD sensor, analyze the pixel value's change by using image J, which is analyzing image program provided by NIH(National Institutes of Health). In case of film, while 0.12sec and 0.25sec show regular rising pattern of density gap as exposure time's increase, 0.4sec shows low rather than 0.12sec and 0.25sec. In case of CCD sensor density test, the result shows opposite pattern of film. This makes me think that pixels of CCD's sensor can have 0~255 value but it becomes saturation if the value is over 255. The way that getting clear reception during decreasing human's exposed radiation is one of maintaining an equipment as a best condition. So we should keeping a dental radiation equipment's condition steadily through cyclic permanent test after factor examination. Even digital equipment doesn't maintain a permanent, it can maintain a clarity by post processing of image so that hard to set it as standard of permanent test. Therefore it would be more increase the accuracy that compare a film as standard image. Thus I consider it will be an important measurement to care for dental radiation equipment and warrant homogeneity, consistency of dental image's clarity through comparing pattern which is the result from factor test against cyclic permanent test.

• Journal of electromagnetic engineering and science
• /
• v.7 no.3
• /
• pp.129-133
• /
• 2007

In this paper, we present the development of an antenna specialized for the maritime collision avoidance system. This antenna is configured as the dielectric rod partially embedded in the metal cavity to reduce the overall size, simultaneously assuring the mechanical sturdiness against the challenging oceanic weather conditions. More importantly, the design has been carefully done to meet the requirements on the radiation pattern(with the slope < 5 dB/deg in the elevation(E-plane), circular in the azimuth) suitable to receiving the reflected signals from the other objects on the sea. To find the optimal design parameters, the genetic algorithm has been used to meet the goals of the desired return loss and pattern. This design methodology is validated by the good agreement between the calculation and measurement.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.10
• /
• pp.791-798
• /
• 1991

In this paper, microstrip array antenna with the phase lock are designed to consist of main lobe and sidelobe with difference 21.97dB for sharp beam pattern using Tchebyscheff polynominals. Microstrip array antenna with phase lock of 0$^{\circ}$, 45$^{\circ}$, 90$^{\circ}$ are designed, to scan beam for 0$^{\circ}$, 6$^{\circ}$, 12$^{\circ}$ to be 1:2:2:1 for the relative current distribution. The designed microstrip array antenna with phase lock is measured in terms of various characteristics such as return loss, resonant frequency, radiation pattern, bandwidth, beamwidth, and the measurement value and theoretical value agreed with each other. Also, the patch array antenna with the relative current distribution is presented phase shift for beam scanning.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4125-4130
• /
• 2015

This paper presents the communication performance for the radiation pattern reconfigurable antenna in the wearable device measuring bio signal (temperature, blood pressure, pulse etc.) of human body. The operational frequency is 2.4 - 2.5 GHz, which covers Bluetooth communication bandwidth. The maximum gain of the antennas is 1.96 dBi. The proposed antenna is efficiently transmitting and receiving signal by generating two opposite beam directions using two RF switches (PIN diode). Also, we investigated how radiation pattern changes according to three angles ($30^{\circ}$, $90^{\circ}$, $150^{\circ}$) of Top Loading. In this paper, we measured and compared the SNR (Signal-to-Noise Ratio) and BER (Bit Error Rate) performances of the proposed antennas in the condition between an ideal environment of anechoic chamber and smart house existing practical electromagnetic interferences (Universal Software Radio Peripheral, USRP). Throughout the comparing the results of the measurement of two cases, we found that the SNR is degraded over 5dB in average and BER is increased over ten times in maximum, therefore, it is confirmed that the error rate of receiving signal is increased. The measured results of SNR and BER value in this paper able to expect the performance degrading by the interference from the electromagnetic devices.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.723-726
• /
• 2002

This paper describes the design, fabrication, and measurement of a sequential-rotation microstrip-array antenna for the Electronic Toll Collection System (ETCS). The ETCS is made possible by using roadside equipment with radiation pattern that can accurately pinpoint the designated communication area, without interference from other lanes. The sequential-rotation microstrip-array antenna was applied to the absorber to reduce the side lobe level (SLL). Results showed that the antenna yields a return loss at a center frequency of -20.675 dB, an axial ratio of 1.15 dB, and a gain of 20.26 dBi.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.2
• /
• pp.188-193
• /
• 2007

Tracking and erosion of Poly Methyl Methacrylate (PMMA) and the suppression mechanism of alumina trihydrate were investigated in the present study The conventional testing as IEC-60587 is widely used in surface aging measurement of outdoor insulator those testing can carry out very short time for Lab testing. Also IEC-60587 testing is able to offer the standard judgement of relative degradation level of outdoor HV system. Therefore it is very useful method compare to previous conventional tracking testing method, But surface discharges(SD) have very complex characteristics of discharge pattern so it is required estimation research to development of precise analysis method. In recent, the study of IRR-Camera is carrying out discover of temperature of power equipment through condition diagnosis and system development of degradation diagnosis. In this paper, SD occurred from IEC-60587 is measured with the surface temperature of weibull distribution in real time, the degradation grade of SD is analyzed through produced patterns in IEC-60587 using Infrared Radiation(IRR) camera.

• Journal of the Korean Society for Precision Engineering
• /
• v.4 no.2
• /
• pp.36-46
• /
• 1987

An optical technique using laser for non-contact measurement of surface roughness and form accuracy of ground surfaces is presented. It is found that, when a ground surface is illuminated by a beam of laser light, the roughness height and slope distribution has significant influence on the pattern of reflection and it maintains an unique Gaussian distribution relationship with the surface roughness. The principle idea of the optical measurement system is therefore monitor the radiation, and then calibrate it in process against surface roughness by means of necessary digital data processing. On the other hand, measuring the form accuracy of a ground surface is accomplished by using a triangular method, which is based on observing the movement of an image of a spot of light projected onto the surface. The image is focused, through a series of lenses for magnification, on a photodetector array lf line configur- ation. Then the relative movement of image and consequently the form accuracy of the surface can be obtained through appropriate calibration procedures. Experimental test showed that the optical roughness measurement technique suggested in this work is very efficient for most industrial applications being capable of monitoring the roughness heights ranging 0.1 to 0.6 .$\mu$m CLA values. And form accuracy can be measured in process with a resolution of 10 .$\mu$m.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.629-636
• /
• 2011

This paper presents the design of a novel integrated T-DMB/GPS/Mobile antenna for vehicular application. The T-DMB antenna is designed with a modified meander-type microstrip patch providing linearly a polarized broadside radiation pattern. The GPS antenna is designed with an inserted slot in the patch antenna providing circularly polarized broadside radiation pattern. The Mobile (GSM, AMPS, DCS, PCS, UMTS, etc.) antenna is designed as a modified G-type patch antenna providing multi-band operation. Experimental results indicate that the impedance bandwidth (VSWR 1:2.5) of the proposed T-DMB /GPS/Mobile antenna satisfactorily matches that of the simulation results. The 2D and 3D radiation patterns and gains according to the results of the experiment are also presented and discussed.