• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.609-614
• /
• 2014

This study is on the experiment of the pipe noise due to the internal fluid. The straight pipe, the $90^{\circ}$ mitred pipe, rounded $90^{\circ}$ and $1350^{\circ}$ pipe were tested and measured the vibration and noise. In the experiment, the vibration and noise level of the straight pipe and rounded pipes show that the vibration and noise level are almost same. The $90^{\circ}$ mitred pipe shows the high vibration and noise level. In the prediction of noise due to the internal flow, the use of pipe surface vibration and radiation efficiency shows good agreement with experiment result.

• 대한방사선기술학회지:방사선기술과학
• /
• 제40권1호
• /
• pp.71-78
• /
• 2017

디지털 방사선영상 시스템에서 산란선은 피검사체와 엑스선의 반응에 의해 발생하는 근원적인 현상이다. 방사선 투사영상은 일차선에 의해 형성되는 감쇠정보를 영상화 하므로 산란선은 투사영상에서 노이즈로써 작용한다. 본 연구에서는 다양한 검사조건에서 발생하는 산란선을 빔 저지체(beam stopper)를 이용하여 정량화하고 동시에 반 산란 격자의 효과를 확인하였다. 또한 산란선이 영상의 품질에 미치는 영향을 확인하기 위해 산란선에 의해 저하되는 대조도 대 잡음비를 측정하였다. 본 연구를 통해 산란선은 피검사체의 두께 및 공기층(air gap)에 지배적인 경향을 가짐을 확인하였다. 또한 산란선은 영상의 대조도를 현격히 저하시킴을 정량적으로 측정하였다. 산란선을 저감하기 위해 격자를 장착함으로써 상당량의 산란선을 저감할 수 있었으나 여전히 두꺼운 피검사체에 대해 많은 양의 산란선이 남아 있음을 확인하였다. 본 연구에서는 산란선을 정량화 하는 방법론을 제시하였으며, 향후 시스템의 최적화에 중요한 역할을 할 수 있을 것으로 기대된다.

• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.20-28
• /
• 1989

본 연구에서는 경계조건에 대한 음향 방사율을 계산하고, 또한 각각의 구조물을 가진하여 진동을 측정하여 음향 방사 파워를 예측한다.

• 한국자동차공학회논문집
• /
• 제19권1호
• /
• pp.139-146
• /
• 2011

In present study, it aims to compare the noise and vibration characteristics between magnesium alloy and steel hood panel. The AZ31 magnesium hood panel was fabricated through warm forming process, and the noise and vibration characteristics between both hood panels was compared through the measurement of engine radiation noise and transmission loss, as well as FRF on modal analysis. The sound insulation performance of magnesium alloy was wholly superior to that of steel hood panel, even though the transmission loss of magnesium alloy is lower than that of steel due to mass effect primarily. The FRF characteristics on modal analysis indicates that the resonance frequency of magnesium hood panel is remarkably increased to higher value than that of steel hood panel. The radiation and interior noise of magnesium panel even without acoustic hood insulation were remarkably lower than those of steel hood panel with acoustic insulation, in particular, at a range below 4,000 rpm.

• 한국음향학회지
• /
• 제33권4호
• /
• pp.238-247
• /
• 2014

본 논문에서는 철도 전동 소음의 주요 소음원인 레일 소음의 방사 특성을 이론적으로 해석하고 배열 마이크로폰을 이용한 레일 소음 측정 시 발생하는 현상들에 관해 이론적으로 고찰하였다. 철도 궤도는 국내 고속철도 콘크리트 도상 궤도를 대상으로 하였으며, 레일에 고속의 이동 하중이 작용하는 경우에 대한 진동 및 소음 방사 특성을 해석하였다. 본 연구를 통해 이동 하중이 작용할 때 발생하는 레일의 소음 방사 특성을 파악하였으며, 배열 마이크로폰을 이용한 레일 소음 측정시 빔 각도가 배열 마이크로폰 출력 음압에 중요하게 작용함을 확인하였다. 따라서 배열 마이크로폰을 이용해 레일 소음을 규명하기 위해서는 레일의 방사 특성을 반영한 배열 마이크로폰 빔 각도 설정이 필요함을 이해하였다.

• 한국전자파학회논문지
• /
• 제14권3호
• /
• pp.233-238
• /
• 2003

고속 회로의 발전과 함께 고주파 잡음의 발생 가능성이 커지고, 이러한 시스템의 잡음 억제를 위해 다중 접지(multipoint ground)가 사용되고 있다. 이 가운데 스크류를 이용한 인쇄회로기판의 접지는 인접 스크류들 사이에 접지 루프를 형성하여 방사잡음을 유발한다. 본 논문에서는 이러한 문제를 해결하기 위하여 기구물(chassis)에 대한 인쇄회로기판의 접지 구조를 제안하였다. 제안된 구조는 전파흡수체와 전도성 구리 테이프를 이용해서 전파 흡수량을 증가시킨 것이다. 1~3 ㎓대역에서 기판의 방사 잡음을 측정한 결과, 제안된 접지 구조는 스크류 접지 구조에 비해 2 ㎓ 이하의 대역에서 방사 잡음이 2.62 dBuV/m 감소되었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권12호
• /
• pp.620-625
• /
• 2004

In this paper, we studied the emissive electric field due to the communication signal and the noise in medium voltage power-line. There are many types of conductive noise in power-line channel, which gives rise to radiation. And if the DMT carrier signal was excited, the current by this term was added to the current by noise and, generate radiation. We calculated input impedance by means of signal input network model of medium voltage power-line channel for calculating these currents. We calculated currents by input impedance and, calculated the emissive electric field by this calculated currents. From the measurement results, we knew that the measured results are very similar to the calculated results and if the input signal power level was higher than -40 dBm, the emissive electric field exceeds FCC radiation limit level 69.5 dB$\mu$V/m.

• 소음진동
• /
• 제6권6호
• /
• pp.781-790
• /
• 1996

The goal of current research is to suppress the acoustic noise radiated from vibration of composite plate structure. The induced noise can be reduced through the control of the corresponding structural vibration modes by using the piezoelectric materials as actuator. The acoustic fields are to be analyzed through the boundary element method (BEM) based on the Rayleigh intergral equation and structural system through the finite element method (FEM). The suppression of rediated sound is studied by adaping the piezoelectric material as the distributed actuator. Numerical results are presented on the sound radiation from composite plate of arbitrary boundary conditions, the noise reduction adapting the piezoelectric materials as distributed actuator. The results show the effectiveness and possibility of piezoelectric actuator in the control of sound radiation from composite structure.

• 한국군사과학기술학회지
• /
• 제6권2호
• /
• pp.20-34
• /
• 2003

The good sea-keeping capability of the SWATH(Small Waterplane Area Twin Hull) ship has been attractive for research or surveillance vessels. Especially, for the naval ships accomplishing the underwater acoustic missions, it is necessary to access and minimize the underwater radiated noise level generated by the ships. Therefore, acoustic signature management and control are very important topics for these vessels. Underwater radiation pattern in the low frequency range is dominated by the tonals from the vibration of onboard machinery. In this work, the radiated noise level generated by the propulsion machine in the submerged hull is predicted using the transfer function technique and the hull transfer function for the submerged hull is determined by analyzing the longitudinal/circumferential stiffened infinitely long cylindrical shell and considering the empirical database of the previous vessels. It is confirmed that the transfer function technique can give useful information for identifying the noise source and estimating its contribution to the total radiatied noise level.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.381-384
• /
• 2005

The purpose of this study is to develop a prediction model for evaluating heavy-weight floor impact sounds in a test building. Three rooms in the test building (slab thickness In and 240mm), which consist of frame concrete structures were tested and modeled. First, the SPL distribution in the receiving room was analyzed by measuring SPL at 90 positions using a bang machine. Then, a vibration model using finite element method is proposed considering the material properties and boundary conditions. In addition, the result of transient analysis was compared with field measurements using a standard heavy-weight impact source. Through a vibro-acoustic simulation program, an acoustic model evaluating the building elements (reflected wall, nor, window and door) was proposed. Finally, validation of the prediction model was conducted by vibro-acoustic analysis with field measurements of noise radiation characteristics in receiving rooms.