• Journal of the Korean Society of Radiology
• /
• v.5 no.5
• /
• pp.283-287
• /
• 2011

In this study, fine $Gd_2O_2S$:Tb powder was synthesized by using a low temperature solution-combustion method for a high-resolution digital x-ray imaging detector. From the fabricated phosphor power, the fine scintillator films was fabricated by particle sedimentation method and was investigated the luminescent property. From the experimental results of relative light output as a function of terbium concentration, the highest luminescent efficiency has at 5 wt% Tb concentration, and luminescent intensity decreased rapidly according to quenching effect about higher Tb concentration. Also, the relative light output of $270{\mu}m$-$Gd_2O_2S$:Tb film has 2945 pC/$cm^2$/mR. And light intensity was saturated at higher film thickness. Finally, to evaluate an image acquisition performance of fabricated phosphor, images were obtained by using commercial CMOS sensor and measured the MTF, NPS, and DQE. DQE(0 lp/mm) of fine phosphor film has 37%. But, DQE improvement of fine phosphor film is possible by resolving problem of film fabrication process and has a significant potential in the application of digital radiation imaging system later.

• Research in Plant Disease
• /
• v.18 no.4
• /
• pp.354-360
• /
• 2012

This study tested the antifungal compound obtained from a medicinal plant, Dioscorea quinqueloba Thunb., in order to search the possibility of practical application of this product in agriculture through evaluating its activity using the citrus fruits. The extract of D. quinqueloba Thunb., which has the strongest antifungal activity, was selected as a candidate among 101 plant extracts. Based on this examination concerning antifungal activity of the product on Penicillium digitatum in vitro, it was confirmed its effect of mycelial growth inhibition showed over 87% at 0.5 mg/ml concentration. This natural product showed the stability of the substance, as it was not significantly influenced by pH, temperature, or ultraviolet radiation. While citrus fruits were stored at room temperature, P. digitatum was inoculated into them in order to prepare a similar environmental conditions with epidemic occurrence of the mold. As the result of our investigation, the disease preventive effects of the active antifungal substance evidenced a 100% at 0.5 mg/ml. When the phytotoxicity of the selected natural product on citrus at 2 mg/ml was assessed, we noted no toxic effects. Based on the superior preventive effects from this natural product extracted from the plant, it is presumed to be very useful in agricultural applications for the control of green mold, P. digitatum, which has been occurred often the biggest problem in the storage of citrus fruits.

• Korean Journal of Food Science and Technology
• /
• v.44 no.5
• /
• pp.532-539
• /
• 2012

Electron spin resonance (ESR) spectroscopy of gamma-irradiated fresh broccoli and kimchi cabbage was conducted to identify their irradiation history. Different pretreatments, such as freeze-drying (FD), oven-drying (OD), alcoholic-drying (ALD), and water-washing and alcoholic-drying (WAD) were used to lower the moisture contents of the samples prior to ESR analysis. The non-irradiated samples exhibited a single central signal ($g_0$=2.0007) with clear effect of $Mn^{2+}$, especially in kimchi cabbage. Upon irradiation, there was an increase in the intensity of the central signal, and two side peaks, mutually spaced at 6 mT, were also observed. These side peaks with $g_1$ (left)=2.023 and $g_2$ (right)=1.985 were attributed to radiation-induced cellulose radicals. Leaf and stem in broccoli, and root and stem in kimchi cabbage provided good ESR signal responses upon irradiation. The signal noise was reduced in case of ALD and WAD pretreatments, particularly due to $Mn^{2+}$ signals. The ALD treatment was found most feasible to detect the improved ESR spectra in the irradiated samples.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.95.1-95.1
• /
• 2010

Transparent conducting ZnO films were deposited to apply DSSC Substrate on glass substrates at $500^{\circ}C$ by ionbeam-assisted deposition. Crystallinity, microstructure, surface roughness, chemical composition, electrical and optical properties of the films were investigated as a function of deposition parameters such as ion energy, and substrate temperature. The microstructure of the polycrystalline ZnO films on the glass substrate were closely related to the oxygen ion energy, arrival ratio of oxygen to Zinc Ion bombarded on the growing surface. The main effect of energetic ion bombardment on the growing surface of the film may be divided into two categories; 1) the enhancement of adatom mobility at low energetic ion bombardment and 2) the surface damage by radiation damage at high energetic ion bombardment. The domain structure was obtained in the films deposited at 300 eV. With increasing the ion energy to 600 eV, the domain structure was changed into the grain structure. In case of the low energy ion bombardment of 300 eV, the microstructure of the film was changed from the grain structure to the domain structure with increasing arrival ratio. At the high energy ion bombardment of 600 eV, however, the only grain structure was observed. The electrical properties of the deposited films were significantly related to the change of microstructure. The films with the domain structure had larger carrier concentration and mobility than those with the grain structure, because the grain boundary scattering was reduced in the large size domains compared with the small size grains. The optical transmittance of ZnO films was dependent on a surface roughness. The ZnO films with small surface roughness, represented high transmittance in the visible range because of a decreased light surface scattering. By varying the ion energy and arrival ratio, the resistivity and optical transmittance of the films were varied from $1.1{\times}10^{-4}$ to $2.3{\times}10^{-2}{\Omega}cm$ and from 80 to 87%, respectively. The ZnO film deposited at 300 eV, and substrate temperature of $500^{\circ}C$ had the resistivity of $1.1{\times}10^{-4}{\Omega}cm$ and optical transmittance of 85% in visible range. As a result of experiments, we provides a suggestition that ZnO thin Films can be effectively used as the DSSC substrate Materials.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.11
• /
• pp.4417-4422
• /
• 2014

ERCC2 is an essential component of the nucleotide excision repair pathway which is involved in the effective maintenance of genome integrity. Association studies on ERCC2 polymorphisms and glioma risk have yielded inconclusive results. This meta-analysis was performed to gain a better insight into the relationship between ERCC2 polymorphisms and glioma risk. A systematic literature search updated to December 2, 2013 was performed in the Pubmed and EMBASE databases. Crude pooled odds ratios (ORs) with their corresponding 95% confidence intervals (95% CIs) were used to estimate the association between ERCC2 polymorphisms and glioma risk under a suitable effect model according to heterogeneity. All analyses were performed using Review Manager 5 (version 5.2) and STATA (version 12.0). The combined results demonstrated rs13181 to be significantly associated with glioma risk (G allele versus T allele: OR=1.15, 95% CI=1.05-1.26, P=0.002; dominant model: OR=1.22, 95% CI=1.07-1.39, P=0.002; recessive model: OR=1.18, 95% CI=0.98-1.41, P=0.070). We also found that rs13181 acts in an allele dose-dependent manner (GG versus TT: OR=1.30, 95% CI=1.07-1.57, P=0.009; TG versus TT: OR=1.20, 95%=CI 1.05-1.37, P=0.009; trend test, P=0.004). However, no evidence was found in analyses for the association between other 3 ERCC2 polymorphisms (rs238406, rs1799793, and rs1052555) and susceptibility to glioma development. Our meta-analysis suggests that rs13181 is significantly associated with glioma risk in an allele dose-dependent manner, whereas, 3 other ERCC2 polymorphisms (rs238406, rs1799793, and rs1052555) may have no influence.

• Journal of Korean Society of Forest Science
• /
• v.85 no.3
• /
• pp.462-471
• /
• 1996

This study was conducted to investigate the effects of meteorological changes on tree growth due to the reservoir construction. First, climatic normals were estimated before and after the reservoir construction at the area of Imha, through the topoclimatological relationships. Secondly, the amount of meteorological changes was quantified based on the difference analysis of the climatic normals. Thirdly, the diameter increments of Pinus densiflora around Imha area were measured with increment borer. Sample trees were taken on the 6 points of 30m, 100m, 500m, 1km, 3km, and 5km from the reservoir, respectively. Finally, effects of meteorological changes on tree growth were investigated based on the analysis of tree ring increment patterns. Results showed that the growth of trees within the range of 1km from the reservoir had been increased, but the growth of ones out of 1km range had no relationship with meteorological changes after the reservoir construction. It seems that the diameter increment of trees grown near reservoir has been increased mainly due to the increased solar radiation in spring and the increased total amount of precipitation during growing season, compared with those before the reservoir construction. It is supposed, however, that the changes of monthly mean temperature has little effect on the tree growth because of its small amount of changes.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.1-10
• /
• 2017

This study examined the risk of accidents when handling hazardous materials in hazardous materials storage facilities without safety facilities. In the case of illegal dangerous cargo containers, the burning rate is very fast in the case of fire, which leads to explosions, that are damaging and difficult to control. In addition, accidents that occur in flammable liquid hazardous materials are caused mostly by accidents that occur in the space due to leakage. Therefore, the variables that affect these accidents were derived and the influence of these variables was investigated. Numerical and computational fluid dynamics programs were used to obtain the following final results. First, when a flammable liquid leaks into a specific space, it is influenced by temperature and relative humidity until a certain concentration (lower limit of combustion) is reached. In the case of temperature, it was found that the reaching time was shorter than the flash point In addition, the effect of variables on pool fire accidents of leakage tanks is somewhat different, but the variables that have the largest influence are the wind speed. Therefore, it is expected that the results of this study will be used as basic data for similar numerical analysis and it will provide useful numerical information about the accidental leakage of hazardous materials under various research conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.9
• /
• pp.535-540
• /
• 2017

The changes in the electrical characteristics of CMOS ICs due to coupling with a narrow-band electromagnetic wave were analyzed in this study. A magnetron (3 kW, 2.45 GHz) was used as the narrow-band electromagnetic source. The DUT was a CMOS logic IC and the gate output was in the ON state. The malfunction of the ICs was confirmed by monitoring the variation of the gate output voltage. It was observed that malfunction (self-reset) and destruction of the ICs occurred as the electric field increased. To confirm the variation of electrical characteristics of the ICs due to the narrow-band electromagnetic wave, the pin-to-pin resistances (Vcc-GND, Vcc-Input1, Input1-GND) and input capacitance of the ICs were measured. The pin-to-pin resistances and input capacitance of the ICs before exposure to the narrow-band electromagnetic waves were $8.57M{\Omega}$ (Vcc-GND), $14.14M{\Omega}$ (Vcc-Input1), $18.24M{\Omega}$ (Input1-GND), and 5 pF (input capacitance). The ICs exposed to narrow-band electromagnetic waves showed mostly similar values, but some error values were observed, such as $2.5{\Omega}$, $50M{\Omega}$, or 71 pF. This is attributed to the breakdown of the pn junction when latch-up in CMOS occurred. In order to confirm surface damage of the ICs, the epoxy molding compound was removed and then studied with an optical microscope. In general, there was severe deterioration in the PCB trace. It is considered that the current density of the trace increased due to the electromagnetic wave, resulting in the deterioration of the trace. The results of this study can be applied as basic data for the analysis of the effect of narrow-band high-power electromagnetic waves on ICs.

• Korean Journal of Food Science and Technology
• /
• v.47 no.1
• /
• pp.13-19
• /
• 2015

The effects of electron beam (e-beam) irradiation at up to 10 kGy on the microbiological and physicochemical properties of dried red pepper powders were studied. Samples from Korea, China, and Vietnam were included in this study. In untreated samples, the total number of microbes, such as total aerobic bacteria, yeasts and molds, was in the range of $10^6-10^7CFU/g$. E-beam irradiation at 5 kGy reduced the microbial load by 2-4 log cycles, thus improving the hygienic quality of the samples. Moisture and pH of the samples were unchanged after e-beam irradiation. Reducing sugar content decreased at 1 kGy, followed by a gradual increase at higher radiation doses. At 5 kGy, no significant changes in the content of capsaicinoids were observed between the irradiated and control samples, while a 10 kGy dose led to a significant decrease. The content of pigments did not exhibit apparent changes with increasing dose of irradiation.

• Progress in Medical Physics
• /
• v.10 no.2
• /
• pp.83-88
• /
• 1999

Purpose: TLD experiments were set up to measure the dose distribution and to analyze the influence on dose measurement of thin metal plate and solid water phantom. The aim of the present study was to investigate the build-up effect of metal plate loaded on TLD chip and depth dose in the controlled environment of phantom measurements. Materials and Methods: Measurements were done by using LiF TLD-100 loaded by a thin metal plate with the same surface area (3.2$\times$3.2 $\textrm{mm}^2$) as TLD chip. TLD chips loaded with one metal plate from three different metal plate (Tin, Copper, Gold) of different thicknesses (0.1, 0.15, 0.2, 0.3 mm) were used respectively to measure radiation dose. Using the TLD loaded with one metal plate, surface dose and the depth dose at the build-up maximum region were investigated. Results: Using a metal plate on TLD chip increased the surface dose. Surface dose curve shows the dose build-up against equivalent thickness of metal to water. The values of TL reading obtained by using metal plate at depth of build-up maximum are about 8% to 13% lower than those obtained by normal TLD chip. Conclusion: The metal technique used for TLD dosimetry could provide clinicals information about the build-up of dose up to 4.2mm depth in addition to a depth dose distribution. The results of TLD with a metal plate measurements may help with decisions to boost or bolus certain areas of the skin.