• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.96.1-96.1
• /
• 2011

Halo coronal mass ejections (HCMEs) are major cause of the geomagnetic storms. To minimize the projection effect by coronagraph observations, we consider two CME cone models: an ice-cream cone model and an asymmetric cone model. These models allow us to determine three dimensional parameters of HCMEs such as radial speed, angular width, and the angle between sky plane and cone axis. In this study, we compare these parameters obtained from both models using 50 well-observed HCMEs from 2001 to 2002. Then we obtain the root mean square error (RMS error) between measured projection speeds and estimated ones for the models. As a result, we find that the radial speeds obtained from the models are well correlated with each other (R=0.89), and the correlation coefficient of angular width is 0.68. The correlation coefficient of the angle between sky plane and cone axis is 0.42, which is much smaller than what is expected. The reason may be due to the fact that the source locations of the asymmetric cone model are assumed to be near the center. The average RMS error of the asymmetric cone model (86.2km/s) is slightly smaller than that of the ice-cream cone model (88.6km/s).

• Journal of radiological science and technology
• /
• v.36 no.1
• /
• pp.19-24
• /
• 2013

The measurement of Korea people's Radial-terminal region were frequently measure of the left hand of Radial-terminal region due to the most Korean's are right-handed and it occasionally showed incorrect results. Therefore, in this study, we accessed a correlation with error of measurement and reduced the measurement error invalid. We reviewed 50 adults patients, from March 2012 for a certain period of time, visited the orthopedic center for the neutral position of forearm of plain radiography and measured the left side of the distal radial-terminal region containing the terminal region of the right distal radius. Then we have compared and analysed both T-score. As a result, the lower value of left wrist were 45 out of 75 which is approximately 60% of left wrist group while the lower value of right wrist were 30 out of 75 which is approximately 40% of right wrist group.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.23 no.1
• /
• pp.39-47
• /
• 2005

In this study, three-dimensional information of submarine topography acquired by assembling DGPS method and echo sounder which mainly used in the marine survey. Moreover, the hopper dredging capacity in harbor public affair has been calculated by utilizing kriging, radial basis function and nearest neighbor interpolation. Also, utilization of DGPS/Echo sounder method in calculation of the dredging capacity have been confirmed by comparing and analyzing the hopper dredging capacity and the actual one as per each interpolation. According to this comparison result, in case of applying kriging interpolation, some 1.89% of error rate has been shown as difference of the contents is 15,364 ㎥ and in case of applying radial basis function interpolation and nearest neighbor interpolation, 3.9% and 4.4% of error rates have respectively shown. In case the study for application of the proper interpolation as per characteristics of submarine topography, is preceded in calculation of the dredging capacity relevant to harbor public affairs, it is expected that more speedy and correct calculation for the dredging capacity can be made.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.8-13
• /
• 2008

In this study, an adaptive node generation procedure in the radial point interpolation method is proposed. Since we set the initial configuration of nodes by subdivision of background cell, abrupt changes of inter-nodal distance between higher and lower error regions are unavoidable. This unpreferable nodal spacing induces additional errors. To obtain the smoothy nodal configuration, it's regenerated by local Delaunay triangulation algorithm This technique was originally developed to generate a set of well-shaped triangles and tetrahedra. To demonstrate the performance of proposed scheme, the results of making optimal nodal configuration with adaptive refinement method are investigated for stress concentration problems.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.9
• /
• pp.2456-2469
• /
• 1996

A digital satellite communication channel has a nonlinearity with memory due to saturation characeristis of the high poer amplifier in the satellite and transmitter/receiver linear filter used in the overall system. In this paper, we propose a complex radial basis function network(CRBFN) based adaptive equalizer for compensation of nonlinearities in digital satellite communication channels. The proposed CRBFN untilizes a complex-valued hybrid learning algorithm of k-means clustering and LMS(least mean sequare) algorithm that is an extension of Moody Darken's algorithm for real-valued data. We evaluate performance of CRBFN in terms of symbol error rates and mean squared errors nder various noise conditions for 4-PSK(phase shift keying) digital modulation schemes and compare with those of comples pth order inverse adaptive Volterra filter. The computer simulation results show that the proposed CRBFN ehibits good equalization, low computational complexity and fast learning capabilities.

• Computers and Concrete
• /
• v.3 no.5
• /
• pp.335-355
• /
• 2006

The application of radial basis function neural networks (RBFN) to predict the ultimate torsional strength of reinforced concrete (RC) beams is explored in this study. A database on torsional failure of RC beams with rectangular section subjected to pure torsion was retrieved from past experiments in the literature; several RBFN models are sequentially built, trained and tested. Then the ultimate torsional strength of each beam is determined from the developed RBFN models. In addition, the predictions of the RBFN models are also compared with those obtained using the ACI 318 Code equations. The study shows that the RBFN models give reasonable predictions of the ultimate torsional strength of RC beams. Moreover, the results also show that the RBFN models provide better accuracy than the existing ACI 318 equations for torsion, both in terms of root-mean-square error and coefficients of determination.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.222-229
• /
• 1999

In order to regulate cutting torque in milling, monitoring system should be set to a certain threshold. Radial immersion ratio is an important factor to determine the threshold and should be estimated in process for automatic regulation. In this paper, on-line estimation of the radial immersion ration using spindle motor current in face milling is presented. When a tooth finishes sweeping, a sudden drop of cutting torque occurs. This torque drop is equal to cutting torque acting on a single tooth at the swept angle of cut and can be acquired form cutting torque signals. Average cutting torque per revolution can also be calculate form cutting torque signals. The ratio of cutting torque acting on a single tooth at the swept angle of cut to the average cutting torque per revolution is a function of the swept angle of cut and the number of teeth. Using the magnitude of this ratio, the radial immersion ratio is estimated. Identical algorithm is adopted to estimate the immersion ratio based on the spindle motor current measurement. The experiments performed under different cutting conditions show that the radial immersion ratio can be estimated within 10% error range by the proposed method using spindle motor current.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.57-64
• /
• 2000

In order to regulate cutting torque in milling, monitoring system should be set to a certain threshold. Radial immersion ratio is an important factor to determine the threshold and should be estimated in process for automatic regulation. In this paper, on-line estimation of the radial immersion ratio using spindle motor current in face milling is presented. When a tooth finishes sweeping, a sudden drop of cutting torque occurs. This torque drop is equal to the cutting torque acting on a single tooth at the swept angle of cut and can be acquired from cutting torque signals. Average cutting torque per revolution can also be calculated from cutting torque signals. The ratio of cutting torque acting on a single tooth at the swept angle of cut to the average cutting torque per revolution is a function of the swept angle of cut and the number of teeth. Using the magnitude of this ratio, the radial immersion ratio is estimated. Identical algorithm is adopted to estimate the immersion ratio based on the spindle motor current measurement. The experiments performed under different cutting conditions show that the radial immersion ratio can be estimated within 10% error range by the proposed method using spindle motor current. Varying immersion ratio is also estimated well using the presented algorithm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.333-337
• /
• 1996

The spindle directly affects parts accuracy during machining, or work piece in machine tools. In this paper a comprehensive study is performed combined mr performance of machine tool spindle. The developed methology has been practically applied to a spindle of machine tools.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.4 no.3
• /
• pp.58-66
• /
• 1995

It is very important to test motion accuracy and performance of NC machine tools as they affect that of all other machines machined by them in industry. In this paper, in has become possible to detect errors of linear displacement of radial direction for circular motion test using newly assembled magnetic type of linear scales so called Magnescale ball bar system, and to calculate time interval getting error motion data and revolution angle of circular motion in machining center using tick pulses come out from computer. And a set of error data gotten from test is expressed to a plot by computer treatment and to numerics of error motion by statistical treatment and results of test are compared with those of Renishaw ball bar system.