• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.4
• /
• pp.421-427
• /
• 2015

This study aims at reviewing first the cases of marine accidents of small fishing vessels and vessels towing and being towed and, the problems concerning such lights and shapes that could be misunderstood for those in concerned Rules, or that could impair their distinctive characteristics or obstruct to keep a proper look-out. And then I wish to make a suggestion of the necessity of amending the National Laws which stipulate the rules for the ship's lights and shapes as follows; Firstly, by amending the "Standard of Construction and Equipment for the Less Than 10 Gross Tonnage of Small Fishing Vessels" small fishing vessel must be equipped with the lights and shapes that are the same as those of "vessel engaged in fishing" prescribed by Rule 26 of the "COLREG 1972" and Rule 84 of the "Maritime Safety Law Act". Secondly, "Standard of Fishing Vessels Equipment" which stipulate the rules concerning the exception of the running lights and radar reflector for the small fishing vessels must be amended to meet the requirement of Rule 20 of the "Maritime Safety Act". Thirdly, the definition of "Length of the tow" which prescribed by Rule 2 of the "Maritime Safety Act" must be amended to meet the Rule 24 of the "COLREG 1972". And also I wish to adhere to the importance of displaying the adequate vessel lights and shapes by every mariner for preventing marine accidents.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.408-416
• /
• 2010

A study on the calibration of an X-band HPS(Hongik Polarimetric Scatterometer) system for ground-based operation is presented in this paper. In order to calibrate the scatterometer system, the degree of its distortions are analyzed by comparison between theoretical- and measured-values using the theoretically well-known calibration targets such as a metal sphere, a trihedral corner reflector(CR) and a metal cylinder. The calibration works in the field conditions depend on the precise and stable measurements of those calibration target. we present a measurement technique, so-called, an automatic 2-D target-scanning technique, using the incidence-angle(${\xi}-$ and ${\phi}-$ directions) control of HPS system. Then, we used STCT(Single-Target Calibration Technique) and GCT(General Calibration Technique) to calibrate a distortion of the scatterometer system, and measured the polarimetric RCS(Radar Cross Section) and phase-difference of a trihedral-CR as a test-target to verify the accuracy of the calibration technique. Then, three different types(i.e., 10, 20, 30 cm) of trihedral-CR were used. we obtained the error ranges about ${\pm}1.0$dB, ${\pm}0.5$ dB in a polarimetric RCS and about $-20^{\circ}{\sim}0^{\circ}$ and ${\pm}5^{\circ}$ in the co-polarized phase-difference by using the GCT and STCT, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.3
• /
• pp.32-39
• /
• 2009

In this paper, system optimization design technique of an impulse ground penetrating image radar (GPIR) in time domain is proposed to improve depth resolution of the system. For the purpose, time domain analysis method of key components such as impulse generator and UWB antenna is explained and by simulation, parameters of each component are determined. In particular, by standardizing the impulse signal, spectrum efficiency of a radiated impulse signal is improved and a U-shaped planar dipole antenna for a UWB antenna is developed. By equipping a parabolic metal reflector with the proposed antenna, external noise is prevented and the ability of radiating an input impulse into ground is improved. In addition, to remove ringing effect of the propose antenna which causes serious degradation of the system performance, resistors are loaded at the edge of the antenna and then Tx and Rx UWB antennas are optimized by simulation in time domain. For images of targets buried under the ground migration technique is applied and influence of tough ground surface on distortion of received impulse signals is reduced using technique of noise and signal distortion reduction in time domain and its time resolution is enhanced. To verify the design optimization procedure, a prototype of an GPIR and an artificial test field are made. Measurement results show that the resolution of the system designed is as good as that of a theoretical model.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.1
• /
• pp.12-17
• /
• 2018

This study describes the design and implementation of Antenna for Digital Satellite Communication. The Antenna unit for SHF band consists of Reflector, Septom Polarizer, Feed Horn and Support Frame etc. Thought analysis of space environment before production, the possibility of the malfunction of equipment minimized and we designed a reliable Antenna through simulation for vibration and thermal analysis generated during the launch, and compared pre-simulation of main performance results to test results about main performances of Antenna after production. After fabricating the antenna, the maximum gain of the antenna main beam is 36.5dBi, which satisfies the requirement of 35dBi or more, and it also satisfies the requirement of -20dB for return loss of less than -24dB. Also, the isolation of the transmission and reception of the antenna is -22.6dB or less, which satisfies the requirement of -20dB or less. The antenna for digital satellite communication described in this paper can be used in the satellite field of geostationary earth orbit and low earth orbit requiring high reliability in the future.

• Journal of the Korean Institute of Navigation
• /
• v.16 no.3
• /
• pp.19-31
• /
• 1992

The Navigational System is the Fundamental System of Port Transportation System and comprises 3 Subsystems, say, the Waterway System, the Shiphandling System and the Support System. The Waterway System of Navigational System is the important and fundamental System for Traffic Safety inside the Port like a Car Road System on Land. This study aims to make a Guideline for the Optimal Waterway System of Port Development and Safety. The Conclusion of this Paper are drawn : 1) The complicated Shiphandling Operations should be avoided for the period of Physical night Time for eliminating the Human Errors. 2) For the Maneuverability and all-weather Combined Piloting the Inside Turn Point Buoy and Begin the-turn Buoy should be mounted with Racon(T) and Radar Reflector for foggy and bad weathers. 3) The Seabuoy located in the Approaching Area for Pilot Station and making Landfall should be mounted with Racon(G) and Morese A Light for giving a Hint of Pilot Station to the Captain on the Bridge, and these Equipments of Racon and Light should be operated normally and effectively even in a Heavy and stormy weathers. 4) A Basic Practical Expression, 1/2 L sin D, for calculating the Extra Width of Cutoff Turn Regions was derived Originally from the Viewpoint of Turn Maneuvers and Maneuverability of the Ship.

• Bulletin of the Korean Space Science Society
• /
• 2010.04a
• /
• pp.28.2-28.2
• /
• 2010

영상레이더 위성으로부터 획득된 SAR 영상의 상대적/절대적 방사(radiometric) 정밀도를 만족시키기 위해서는 궤도상에서 검보정을 수행하여야 한다. 일반적으로 상대 방사 정밀도의 보정을 위해서는 아마존 일대와 같이 일정한 지표 반사도를 지니는 넓은 지역을 촬영함으로써, 지상에서 모델링된 안테나 패턴의 이상 유무를 검증한다. 절대 방사 정밀도를 결정하기 위해서는 보정계수(calibration constant)를 구해야 하는데, 이를 위해서 RCS(radar cross section) 값이 기 알려져 있는 지상의 CR(corner reflector)를 관측해야 한다. 대부분의 SAR 위성의 경우, 각 입사각별로 여러 개의 빔(beam)이 독립적으로 운용되고, 위성의 경로가 각 pass 사이 거의 일정한 간격을 가지기 때문에, 지상의 CR들에 대한 빔의 접근성이 상당히 제약을 많이 받게 된다. 즉, 개별 빔이 촬영할 수 있는 CR의 개수 및 동일 CR에 대한 촬영 빈번도가 많이 작을 수 있다는 것을 의미한다. 특히, CR이 빔폭의 중심에서 관측되어야 하는 요구사항이 추가로 반영될 경우 그 빈도수는 더욱더 영향을 받게된다. 이 연구에서는 고도 550 km, 28일의 지상반복주기(repeat ground track)를 가지는 여명 궤도(dawn-dusk orbit)를 가정하고, 각 빔별로 그 빔에 할당된 하나의 CR만을 촬영해야 된다는 조건하에, 빔 접근성의 요구사항을 최대로 만족시킬 수 있는 CR의 좌표들을 구하였다. 동시에, J2항만을 고려한 이상적 28일 지상반복궤도를 적용한 경우와 모든 중력섭동항을 적용한 최적궤도를 적용한 경우를 비교하여, 실질적 검보정 일정을 수립하였다.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.11
• /
• pp.21-34
• /
• 2017

The ground penetrating radar (GPR) signal can be measured with different amplitudes according to the directivity, so the directivity of the antenna should be considered. The objective of this study is to investigate the directivity of antenna by analyzing the reflection characteristics of electromagnetic waves radiated from the antenna, and to evaluate effective range of angle that can inspect an abnormal area according to the directivity of antenna. For the measurement of the directivity, a circular metal bar is used as reflector and the signals are measured by changing the angle and the distance between reflector and antenna in the E- and H-plane. The boundary distance between the near field and the far field is determined by analyzing the amplitudes of reflected signals, and two points with different distances from each of near and far fields are designated to analyze radiation patterns in near and far fields. As a result of radiation pattern measurement, in the near field, minor lobes are observed at angle section at more than $50^{\circ}$ in both E- and H-plane. Therefore, antenna has the directivity for the direction of main lobe and minor lobes in near field. In the far field, antenna has the directivity for a single direction of main lobe because minor lobes are not observed. The amplitude of the signal reflected from the near field is unstable, but it can be distinguished from noise. Therefore, in the near field, the ground anomaly can be detected with high reliability. On the other hand, the amplitude of the signal reflected from the far field is stable, but it is hard to distinguish between reflected signal and noise because of the excessive loss of electromagnetic wave. The analyses of directivity in the near and the far fields performed in this study may be effectively used to improve the reliability of the analyses of abnormal area.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.25-32
• /
• 1983

The corner reflector is used to increase the echoing area of radar targets in the air, and it can also be applied to increase the echoing area of the sonar targets under water. As the basic research for this application, the authors investigated the ultrasonic reflection characteristics under water for the corner reflector which was made of aluminum plate. The experiments were made by pulse measuring method with the magnetostrictive ferrite transducers of 28, 50 and 75KHz in the experimental water tank. The results obtained are as follows; 1. The target strength of corner reflectors were increased in proportion to the diameter and were greater at higher frequency of 75KHz than at lower frequency of 28KHz. 2. In the case of 5 corner reflectors of 150mm in diameter which have corner angles of 15$^{\circ}$, 30$^{\circ}$, 45$^{\circ}$, 60$^{\circ}$ and 90$^{\circ}$the measured values of the maximum target strength at 75KHz were-25.0 dB, -17.2dB, -15.1dB, -13.4dB and 11.0dB, and then the number of main lobes showing the maximum target strength in the backscattering patterns were 24, 12, 8, 6 and 4, respectively. 3. When 7 corner reflector of 80mm in diameter and 90$^{\circ}$ in the corner angle was located on the minor axis of the horizontal section with directional angles of 0$^{\circ}$, 2.5$^{\circ}$, 5.0$^{\circ}$, 7.5$^{\circ}$, 10$^{\circ}$ and 12.5$^{\circ}$ against the sound beam axis, the measured values of the target strength on each position at 75KHz were -21.2dB, -21.9dB, -26.0dB, -30.5dB and -36.8dB, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.7
• /
• pp.711-719
• /
• 2011

A study of miniaturization of an L-band orthomode transducer(OMT) for field experiments of radar backscatter is presented in this paper. The proposed OMT is not required the additional waveguide taper structures to connect with a standard adaptor by the newly designed junction structure which bases on a waveguide taper. Total length of the OMT for L-band is about 1.2 ${\lambda}_o$(310 mm) and it's a size of 60 % of the existing OMTs. And, to increase the matching and isolation performances of each polarization, two conducting posts are inserted. The bandwidth of 420 MHz and the isolation level of about 40 dB are measured in the operating frequency. The L-band scatterometer consisting of the manufactured OMT, a horn-antenna and network analyzer(Agilent 8753E) was used STCT and 2DTST to analysis the measurement accuracy of radar backscatter. The full-polarimetric RCSs of test-target, 55 cm trihedral corner reflector, measured by the calibrated scatterometer have errors of -0.2 dB and 0.25 dB for vv-/hh-polarization, respectively. The effective isolation level is about 35.8 dB in the operating frequency. Then, the horn-antenna used to measure has the length of 300 mm, the aperture size of $450{\times}450\;mm^2$, and HPBWs of $29.5^{\circ}$ and $36.5^{\circ}$ on the principle E-/H-planes.

• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.305-312
• /
• 2017

The most effective way to distinguish subsurface interfaces that produce various geophysical responses is through the integration of multiple geophysical methods, with each method detecting both a complementary and unique set of distinct physical properties relating to the subsurface. In this study, shallow seismic reflection (SSR) and ground penetrating radar (GPR) surveys were conducted at the Cheongju-Gadeok site of the Korea National Groundwater Monitoring Network to map the water table, which was measured at 12 m depth during the geophysical surveys. The water table proved to be a good target reflector in both datasets, as the abrupt transition from the overlying unsaturated weathered rock to the underlying saturated weathered rock yielded large acoustic impedance and dielectric constant contrasts. The two datasets were depth converted and integrated into a single section, with the SSR and GPR surveys conducted to ensure subsurface imaging at approximately the same wavelength. The GPR data provided detailed information on the upper ~15 m of the section, whereas the SSR data imaged structures at depths of 10-45 m. The integrated section thus captured the full depth coverage of the sandy clay, water table, weathered rock, soft rock, and hard rock structures, which correlated well with local drillcore and water table observations. Incorporation of these two geophysical datasets yielded a synthetic section that resembled a simplified aquifer model, with the best-fitting seismic velocity, dielectric constant, and porosity of the saturated weathered layer being $v_{seismic}=1000m/s$, ${\varepsilon}_r=16$, and ${\phi}=0.32$, respectively.