• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.7
• /
• pp.1332-1339
• /
• 2001

SoC(System on Chip) technology is widely used in the field of embedded systems by providing high flexibility for a specific application domain. An important aspect of development any new embedded system is verification which usually requires lengthy software and hardware co-design. To reduce development cost of design effort, the instruction set of microprocessor must be suitable for a high level language compiler. And FPGA prototype system could be derived and tested for design verification. In this paper, we propose a 16 bit FPGA microprocessor, which is tentatively-named EISC16, based on an EISC(Extendable Instruction Set Computer) architecture for embedded applications. The proposed EISC16 has a 16 bit fixed length instruction set which has the short length offset and small immediate operand. A 16 bit offset and immediate operand could be extended using by an extension register and an extension flag. We developed a cross C/C++ compiler and development software of the EISC16 by porting GNU on an IBM-PC and SUN workstation and compared the object code size created after compiling a C/C. standard library, concluding that EISC16 exhibits a higher code density than existing 16 microprocessors. The proposed EISC16 requires approximately 6,000 gates when designed and synthesized with RTL level VHDL at Xilinix's Virtex XCV300 FPGA. And we design a test board which consists of EISC16 ROM, RAM, LED/LCD panel, periodic timer, input key pad and RS-232C controller. 11 works normally at 7MHz Clock.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12B
• /
• pp.779-789
• /
• 2007

This paper presents an architecture of UPnP Bridge for interconnecting Non-lP devices with heterogeneous network interfaces to UPnP devices on UPnP networks. The proposed UPnP Bridge provides a Virtual UPnP device that performs generic UPnP Device's functionalities on behalf of Non-lP device. This paper defines 3 types of descriptions, Device Description, Message Field Description, and Extended UPnP Service Description in order to reduce the amount of effort required to connect a non-lP device with a new interface or message format to UPnP network. By these three types of descriptions and Message conversion module, developers for Non-lP devices can easily connect the devices to UPnP network without additional programming. So UPnP control point controls Non-lP devices as generic UPnP device. Some experiments validate the proposed architecture, which are performed on a test bed consisting of UPnP network the proposed bridge, and non-lP devices with CAN and RS232 interfaces.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.144-155
• /
• 2013

This paper presents a low-cost remote power-quality-failure monitoring system (RPMS) using Android App and TI MCU (micro-controller unit), which is appliable to a micro-grid. The designed RPMS testbed consists of smart nodes, a server, and Android APPs. Especially, the C2000-series MCU-based RPMS smart node that is low-cost compared to existing monitoring systems has both a signal processing function for power signal processing and a data transmission function for power-quality monitoring data transmission. The signal processing function implements both a wavelet-based power failure detection algorithm including sag, swell, and interruption, and a FFT-based power failure detection algorithm including harmonics such that reliable and real-time power quality monitoring is guaranteed. The data transmission function implements a low-complexity RPMS transmission protocol and defines a simple data format (msg_Diag) for power monitoring message transmission. We may watch the monitoring data in real time both at a server and Android phone Apps connected to the WiFi network (or WAN). We use RS-232 (or Bluetooth) as the wired (or wireless) communication media between a server and nodes. We program the RPMS power-quality-failure monitoring algorithm using C language in the CCS (Code Composer Studio) 3.3 environment.

• Journal of Navigation and Port Research
• /
• v.26 no.4
• /
• pp.419-426
• /
• 2002

The conventional RTK-GPS technique has many problems which are permission using RF wireless modem, influence of geographic obstacle using radio wave, frequency interference, finiteness of frequency resources. To solve these problems, in this paper, we designed the DGPS correction message transmission system as a method to substitute the RF wireless modem of RTK-DGPS receiver. Then the interface module was designed and implemented for linkage of GPS receiver and mobile phone. As a result worked differential surveying using receiving correction message using RS-232C and communication control, users of mobile station were worked differential surveying correction between mobile phones. Interface module system was received the same result of precision which was compared RF wireless modem system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.805-815
• /
• 1994

The development of automatic production systems has a trend toward Computer Integrated Manufacturing System(CIMS) in recent years. In hardware configuration, CIMS are composed of intelligent CAD/CAM work stations, multifunction CNC machining centers including material handling systems. The DNC systems present the key element of automation hierarchy in a FMS. A DNC system is one which connects a number of numerically-controlled machines to a common memory in a digital computer for part program storage with provision for on-demand distribution of part program data to machines using communication in hierarchical structure of central computer, control computer and cell controller. This paper describes the development of Behind-the-Tape-Reader(BTR) type DNC system using CYBER 180-830 as a central computer and IBM PC-386 cell control computer and NC lathe with FANUC 5T NC controller. In this system, the connection between central computer and cell control computer is done via RS-232C serial interface board, and the connection between cell control computer and FANUC 5T controller is done via parallel interface board. The software consists of two module, central computer communication module for NC program downloading and status uploading, NC machine running module for NC operating.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.7
• /
• pp.1289-1295
• /
• 2007

In this paper, we implemented high-performance concurrent control system which manages whole RF systems with digital type and communicates with remote station on both wire and wireless networking. It consists of FPGA (Field Programmable Gate Array) part which controls forward/reverse LPA (Linear Power Amplifier), forward/reverse LNA (Low Noise Amplifier), channel cut wire/wireless TCP/IP, etc, master microprocessor (AVR), which manages the whole control system, Slave microprocessor which communicates SA (Spectrum Analyzer) and observes frequency spectrum of each channel with the resolution of 5KHz, 10 channel card microprocessor which independently observes each channel card and sets frequency synthesizer in channel cut and other peripherals and logics. The whole system is divided to two parts of H/W (hardware) and S/W (software) considering operational efficiency and concurrency, and implementation and cost. H/W consists of FPGA and microprocessor. We expected the optimized operation through H/W and SW co-design and hybrid H/W architecture.

• ETRI Journal
• /
• v.30 no.1
• /
• pp.59-67
• /
• 2008

The necessity for the precise time synchronization of measurement data from multiple sensors is widely recognized in the field of global positioning system/inertial navigation system (GPS/INS) integration. Having precise time synchronization is critical for achieving high data fusion performance. The limitations and advantages of various time synchronization scenarios and existing solutions are investigated in this paper. A criterion for evaluating synchronization accuracy requirements is derived on the basis of a comparison of the Kalman filter innovation series and the platform dynamics. An innovative time synchronization solution using a counter and two latching registers is proposed. The proposed solution has been implemented with off-the-shelf components and tested. The resolution and accuracy analysis shows that the proposed solution can achieve a time synchronization accuracy of 0.1 ms if INS can provide a hard-wired timing signal. A synchronization accuracy of 2 ms was achieved when the test system was used to synchronize a low-grade micro-electromechanical inertial measurement unit (IMU), which has only an RS-232 data output interface.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.583-585
• /
• 1999

This paper presents the controller of multiple DC motors using the network. This controller has been built with 16-bits one chip microprocessor (87C196CA) which includes the integrated CAN serial communication and position control for two motors. Since only one microprocessor is needed, the proposed controller is not only cost effective but also powerful. The system is composed of one main controller, trajectory planner, and the other sub controller, position controller. The main controller which has been built using Visual Basic programming on the Pentium PC, generates the trajectory and then transmits it to the sub controller. The trajectory transmitted from the PC will be processed by the sub controller. Two motors are controlled using the conventional position control, PID, to reach them the same target position but with different velocities at the same time. The communications between the main controller and sub controller is performed through the RS-232 or the CAN communication The CAN would be safer and faster than serial communication network since it has non-destructive bitwise arbitration specification. In this paper, we consider the CAN communications generally and then show the usefulness of the proposed controller by demonstrating position control of two DC motors.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.70.3-70.3
• /
• 2018

외계행성 탐색시스템의 망원경-카메라 제어 시스템 및 소프트웨어 구성과 관측 유틸리티에 대해 소개한다. 망원경 제어 소프트웨어는 천문 위치보정, 포인팅, 돔 회전 등을 담당하는 PC-TCS 프로그램, 망원경 적경-적위 축 서보 제어를 담당하는 full-closed loop PID 컨트롤 프로그램, 포커서, 필터박스, 돔 셔터, 주경냉각, 온도 모니터 등의 보조 시스템을 제어하는 AUX controls 프로그램으로 구성된다. 카메라 제어 소프트웨어는 모자이크로 구성된 여러 CCD를 각각 독립적으로 제어하는 IC(Instrument Control) 패키지와 이들을 총괄 제어하는 ICS(IC Science) 패키지로 구성되며 망원경과 카메라 소프트웨어의 인터페이스 역할을 하는 TCS Agent 프로그램이 포함된다. 관측 진행을 돕는 유틸리티로서 관측제어 명령어 입력 및 관측 스크립트 구동 기능을 제공하는 OBS Agent 프로그램과 가이드 CCD를 이용한 시상 모니터링 및 자동초점조정 프로그램을 개발하여 활용하고 있다. 각 소프트웨어는 UDP, TCP/IP, RS-232, Redis server 등 다양한 인터페이스를 통하여 서로 통신하며, CCD 영상 자료 전달을 위해 RAM(Random Access Memory) 디스크와 Network File System(NSF)을 이용하고 있다.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.25-28
• /
• 2002

본 논문은 마이크로 프로세스로 처리되는 여러 제어장치들 중에서 PI제어기의 최적 자동동조에 관한 개선된 방법을 제안하고자 한다. 이 방법은 Relay 자동동조 법으로서 이를 마이크로 프로세스에 응용하여 제어대상에 최적의 PI계수를 입력하게된다. 이를 위해 먼저 Computer와 DSP사이에 통신이 가능하도록 RS-232를 설치하고, 컴퓨터의 제어신호에 따라 모터의 속도가 Relay와 PI제어기에 의해 목표값에 도달할 수 있도록 설계하였다. 내부적으로 사용된 Relay 동조방식은 Relay로 제어대상의 출력을 강제로 진등시켜서 출력의 진폭과 주기를 이용하여 PI 계수를 조정하고 제어기의 입력값으로 선택된다. Relay동조 법은 동조과정이 간단하여 동조 방식의 구현이 쉽다. 또 위상여유를 고려하여 제어기의 계수를 조정하기 때문에 시스템의 견실성을 향상시킬 수 있을 뿐 아니라, 비례 제어만으로 임계 진동을 하지 않는 시스템의 경우에도 사용할 수 있고, 원점에 극점이 있는 경우에도 적용할 수 있어서 기존의 제어방식이 가지는 제약성의 한계를 극복할 수 있어서 적용성이 우수하다.