• Wind and Structures
• /
• v.5 no.2_3_4
• /
• pp.359-368
• /
• 2002

This paper describes a CFD investigation into the flow over the cab of a bluff-fronted lorry. Several different simulations were undertaken, using the commercial codes: CFX, Fluent and PowerFLOW. Using the $k-{\varepsilon}$ turbulence model, the flow over the cab was symmetric, however, using more accurate turbulence models such as the RNG $k-{\varepsilon}$ model or the Reynolds Stress Model, the flow was asymmetric. The paper discusses whether this phenomenon is a real effect or whether it is a solver artefact and the study is supported by experimental evidence. The findings are preliminary, but suggest that it has a physical origin and that it may be aspect ratio-dependent.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.192-198
• /
• 2004

A numerical study was conducted to determine the effects of high temperature air, including equivalent ratio on flow field, temperature, evaporation, and overall temperature distribution in gas turbine combustor. A sector model of a typical wall jet can combustor, featuring introduction of primary air and dilution air via wall jet, was used in calculations. Flow field and temperature distribution were analyzed. Operating conditions such as inlet temperature and overall equivalent ratio were varied from 373 to 1300 K, and from 0.3 to 0.6, respectively, while any other operating conditions were fixed. The RNG ${\kappa}-{\varepsilon}$ model and eddy breakup model were used for turbulence and combustion model respectively. It was found that the increase with the inlet air temperature, velocity in the combustor is accelerated and evaporation of liquid fuel is not affected in primary zone, high temperature inlet air enhances the evaporation and improves overall temperature distribution factor.

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.118-125
• /
• 2007

The firtst-order conditional moment closure (CMC) model is applied to CH4/air swirl diffusion flame in a gas turbine model combustor. The flow and mixing fields are calculated by fast chemistry assumption with SLFM library and a beta function pdf for mixture fraction. RNG k-e model is used to consider the swirl flame in a confined wall. Reacting scalar fields are calculated by elliptic CMC formulation with chemical kinetic mechanism, GRI Mech 3.0. Validation is done against measurement data for mean flow and scalar fields in the model combustor [1]. Results show reasonable agreement with the mean mixture fraction and its variance, while temperature is overpredicted as the level of local extinction increases. The second-order CMC model is needed to consider local extinction with considerable conditional fluctuations near the nozzle.

• Journal of information and communication convergence engineering
• /
• v.6 no.2
• /
• pp.228-232
• /
• 2008

In recent years, wireless ad hoc networks have become increasingly popular in both military and civilian applications due to their capability of building networks without the need for a pre-existing infrastructure. Recently, IEEE 802.11 Task Group e has been working on a new mechanism, the Enhanced Distributed Coordination Function (EDCF), to enhance the performance of 802.11 DCF. However, EDCF only reduces the internal collisions within a station, and external collisions between stations remain high in ad-hoc networks. In this paper, we propose to adopt an adaptive backoff window control technique, based on a dynamic value of the initial value of the range in which the backoff is chosen, so the backoff timer is randomly chosen in the range (InitRng, CW-1). We use ns-2 simulation to evaluate the throughput of our scheme. Results show that the throughput is improved for our scheme compared to the original DCF due to the reduced the number of collisions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.95-98
• /
• 2003

The physics of the plume-induced shock and separation particulary at a high plume to exit pressure ratio and supersonic speeds up to Mach 3.0 with aid without a passive control method, porous extension, were studied using computational techniques. Mass-averaged Navier-Stokes equations with the RNG k-$\varepsilon$ turbulence model were solved using a fully implicit finite volume scheme and a 4-stage Runge-Kutta method. The courol methodology for plume-afterbody interactions is to use a perforated wall attached at either the nozzle exit or the edge of the missile base. The Effect of porous wall length on plume interference is also investigated. The computational results show the main effect of the porous extension on plume-afterbody interactions is to in the plume from strongly underexpanding during a change in flight conditions. With control, a change in porous extension length has no significant effect on plume interference.

• International Journal of Fluid Machinery and Systems
• /
• v.9 no.3
• /
• pp.237-244
• /
• 2016

An unsteady three-dimensional simulation based on Reynolds time-averaged governing equation and RNG $k-{\varepsilon}$ turbulence model, was presented for pump-as-turbine, the pressure fluctuation characteristic of hydraulic turbine with guide vane was obtained. The results show that the time domains of pressure fluctuation in volute change periodically and have identical cycles. In volute tongue and inlet pressure fluctuations are light, while in dynamic and static coupling interface pressure fluctuations are serious; In impeller blade region the pressure fluctuation of pressure surface are lighter than that of suction surface. The dominant frequencies of pressure fluctuation concentrate in low frequency region, and concentrate within 2 times of the blade passing frequency.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.454-459
• /
• 2001

The present study is concerned with the flow patterns induced by other impellers in a rectangular tank Impellers are FBT(Flat blade turbine), PBT(Pitched blade turbine), Shroud turbine, Rushton Turbine, and Helical ribbon turbine. The solution of flows in moving reference frames requires the use of 'moving' cell zone. The moving zone approaches are MRF(Multiple reference frame), which is a steady-state approximation and Sliding method, which is a unsteady-state approximation. Numerical results using two moving zone approaches are compared with experiments by Ranade & Joshi, which have done extensive LDA measurements of the flow generated by a standard six-bladed Rushton turbine in a cylindrical baffled vessel. In this paper we simulated the flow patterns with above mentioned moving zone approaches and impellers. Turbulence model is RNG k-$\epsilon$ model.

• Journal of Environmental Health Sciences
• /
• v.14 no.1
• /
• pp.55-61
• /
• 1988

Study was conducted on how the phosphorus content of algae changed by the algal species and the algal growth conditions. Phosphorus contents were not so different by algal species if algae grow on the same phosphorus concentration. Phosphorus content of algae grown on higher P medium was higher than that of algae grown on lower P medium. Algae excrete P-compounds from cell to the medium when the dissolved reactive phosphorus is depleted in the medium, and the excreted P-compounds were decomposed by algae and used for the growth of algae. Phosphorus content of algae grown in the P-limited condition was about 5-1 $\mu$gP/mg dry wt., but that of algae grown in the condition not P-lirnited was above 10$\mu$gP/rng dry wt.

• Journal of Environmental Health Sciences
• /
• v.17 no.1
• /
• pp.74-78
• /
• 1991

This study was performed to investigate the effect of heavy metals and CN on BOD$_{5}$ measurement. The results were as follows: 1. The BOD$_{5}$ value decreased 20% in Cd(CdCl$_{2}$) 3.0mg/l, Ni(NiCl$_{2}$) 7.0mg/l, Cu(CuCl$_{2}$) 0.5mg/l, Pb($Pb(NO_{3})_{2}$) 9.0mg/l, Cr($K_{2}Cr_{2}O_{7}$) 1.0mg/l respectively. 2. The BOD$_{5}$ value decreased 10% in Zn($Zn(NO_{3})_{2}$) 5 mg/l, Fe(FeCl$_{3}$) 20mg, /l, and 25% in CN(KCN) 5mg/l, and 40% in Hg(HgCl$_{2}$) 0.2rng/l. 3. In Comparion with BOD Rapid Analyzer, the above mentioned heavy metals concentrations have no effect on BOD$_{5}$ value of that analyzer except CN.

• Journal of computational fluids engineering
• /
• v.1 no.1
• /
• pp.47-54
• /
• 1996

비유선형 물체 주위의 유동은 정체유동, 경계층 박리 및 재부착, 주기적 와열의 생성등의 복잡한 유동현상이 공존한다. 이와 같은 유동의 2-방정식 난류모델을 이용한 정확한 예측은 일반적으로 불가능 하다고 인식되어 왔으나, 본 연구에서는 기존의 비교적 단순한 난류모델을 활용한 정사각주 주위의 비정상 난류유동의 예측 가능성을 체계적으로 규명하였다. 적절한 난류모델의 선정과 더불어 시간 정확도, 공간 정확도 및 대류항 처리법 등이 해석의 결과에 미치는 영향을 살펴 보았다. 기존의 표준 κ-ε모델은 정체점 주위에서 난류생성항의 과도한 예측으로 말미암아 재부착 및 와열생성의 정확한 예측이 불가능 하였으나, RNG κ-ε 모델을 사용한 경우 이와 같은 현상을 제거 할 수 있었다. 그러나 이 경우에도 예측의 정확도가 시간 증분, 격자의 크기 및 대류항 처리법 등에 영향을 받았으며, 특별히 대류항 처리법에 따라 상당히 민감하게 변하는 것을 알 수 있었다.