• Journal of the Microelectronics and Packaging Society
• /
• v.4 no.2
• /
• pp.79-83
• /
• 1997

본 연구에서는 휴대용 전화기 및 무선 LAN 의 핵심부품인 RF-Switch Module의 초소형화 설계기술, 표면실장기술, 고주파설계기술, 소형화 SMD기술, Test 기술 및 RF-Switch Module 활용기술 등을 개발하였으며 RF-Switch Module의 설계기반 마련 및 대외 경쟁력 있는 RF-Switch Module의 초소형화 기술을 확보하였다.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1673-1675
• /
• 2004

The design, modeling and measurement of RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a LTCC multi-layer switching circuit and integrated low pass filter. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.710-713
• /
• 2004

The design, simulation, modeling and measurement of a low temperature co-fired ceramic (LTCC) RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a Rx/Tx switching circuit and integrated low pass filter. The low pass filter function was designed to operate in th GSM band. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ nm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1287-1293
• /
• 2008

Antenna switch module(ASM) for quad-band was developed. This module was integrated by RFIPD(RF integrated passive device) and transistor switch instead of LTCC-type device using low pass filters, diodes and passive elements in RF front end module for cellular phone. This module leads to low cost and miniaturization(The area is $5{\times}5\;mm$ and the thickness is 0.8 mm). The insertion loss and the return loss of each band were averagely measured as 1.0 dB(insertion loss), 15.1 dB(GSM/EGSM return loss) and 19 dB(DCS/PCS return loss), respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.431-434
• /
• 2004

The design, simulation, modeling and measurement of a RF switch module for GSM applications were presented in this paper. switch module were simulated by ADS and constructed using a LTCC multi-layer switching circuit and integrated low pass filter, designed to operate in the GSM band. Insertion and return losses at 900 MHz of the low pass filters were designed to lower than 0.3 dB and higher than 12.7 dB respectively. The switch module constructed, contained 10 embedded passives and 3 surface mounted components integrated on $4.6{\times}4.8{\times}1.2$ m volume, 6-layer integrated circuit. The insertion loss of switch module at m MHz were around 11 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.362-370
• /
• 2010

In this paper, a compact RF Front-end module for Wireless Fidelity(Wi-Fi) and Worldwide Interoperability for Microwave Access(WiMAX) applications is realized by low temperature co-fired ceramic(LTCC) technology. The RF Front-end module is composed of three LTCC band-pass filters, a Film Bulk Acoustic Resonator(FBAR) filter, fully embedded matching circuits, an SPDT switch for mode selection, an SPDT switch for Tx/Rx selection, and an SP4T switch for band selection. The parasitic elements of 0.2~0.3 pF are generated by the structure of stacking in the top pad pattern for DC block capacitor of SPDT switch for mode selection. These kinds of parasitic elements break the matching characteristic, and thus, the overall electrical performance of the module is degraded. In order to compensate it, we insert a parallel lumped-element inductor on capacitor pad pattern for DC block, so that we obtain the optimized performance of the RF Front-end module. The fabricated RF front-end module has 12 layers including three inner grounds and it occupies less than $6.0mm{\times}6.0mm{\times}0.728mm$.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.77-81
• /
• 2011

This paper presents a single-pole eight-throw(SP8T) switch based on proposed a radio-frequency(RF) microelectromechanical systems (MEMS) switches. The proposed switch was driven by a double stop(DS) comb drive, with a lateral resistive contact. Additionally, the proposed switch was designed to have tapered signal line and bi-directionally actuated. A forward actuation connects between signal lines and contact part, and the output becomes on-state. A reverse actuation connects between ground lines and contact part, and the output becomes off-state. The SP8T switch of 3-stage tree topology was developed based on an arrangement of the proposed RF MEMS switches. The developed SP8T switch had an actuation voltage of 12 V, an insertion loss of 1.3 dB, a return loss of 15.1 dB, and an isolation of 31.4 dB at 6 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.8
• /
• pp.958-966
• /
• 2012

This paper presents a compact bluetooth/WiFi dual-mode dual-band RF front-end module(FEM) is realized by low temperature co-fired ceramic(LTCC) technology. The proposed RF front-end module consists of a diplexer, baluns in the LTCC substrate, and an SPDT switch, an SP3T switch on the LTCC substrate. In order to reduce the module size and increase integration level, the proposed diplexer and balun are designed using LC lumped elements. The parasitic elements caused by coupling effect between metal pattern layers and ground plane layer are considered during the design. The fabricated dual-mode RF front-end module has 13 pattern layers including three inner ground layers and it occupies less than $3.0mm{\times}3.7mm{\times}0.66mm$.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.3
• /
• pp.1-11
• /
• 1999

It is now common practice to utilize the quadrature RF coils to improve the signal-to-noise ratio (SNR) in the Magnetic Resonance Imaging (MRI) System. In addition, to make such an available SNR improvement, it is mandatory to use a well-designed quadrature coupler, which facilitates a perfect 3-dB coupling and quadrature-phase shift. However, the four ports matching condition has to be well considered during the RF excitation and the signal detection period. This work investigates the effects of such a mismatching condition (especially, due to patient) from the analysis, simulation, and real implementation and firstly proposes dynamic loading technique for a quadrature coupler and transmitting/receiving switch module to minimize a patient mismatching and enhance a system reliability. Also, we designed and implemented the quadrature coupler and transmitting/receiving switch module using microstrip. As a result, the SNR of our MRI system using the microstrip quadrature coupler and transmitting/receiving switch module with dynamic load increases 3 dB compared with the old one using USA quadrature switch. Also, the power capability of quadrature coupler and transmitting/receiving switch module is 5-kw peak power. Considering power loss and reduction of size, we used a RT/duroid 6010 substrate with high permittivity and for simulation we use Compact Software.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.12
• /
• pp.2417-2424
• /
• 2016

Small size and light weight is very important for components used in radar mounted platform such as airborne radar. Recently, the active phased array radar is developed as an array of antennas for thousands of transmit/receive modules to be used as a multi-function radar that can detect and track targets. In this case, the size and weight of the transmit/receive modules are critical factor for developing the radar. In this paper, we developed a compact transmit/receive module using the 10W RF MEMS switch domestically localizing and reduced the circuit area to about 86.5% compared to using a circulator. The developed module satisfies not only electrical requirements but also MIL-STD's environmental specifications. So it can be used in a military device. It can be used at adaptive tunable receivers, reconfigurable smart active antennas and wide band beam electrical steering antennas.