• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.85-91
• /
• 2017

This paper concerns the design of a matching module system enabling the RF signal to be harmonized between the new base stations (RRH) and the repeater in the same frequency band of the asynchronous transfer network. This matching system controls the RF Gain Control of the module while monitoring the quality of the quality. Additionally, the RF environment has been adapted accordingly to adjust the RF Gain Control to match the receiver characteristics of the relay. As a result of this study, we improved the quality of the interface between the new base stations and existing relays.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2173-2175
• /
• 2004

This paper addresses a telemetering device which uses RF transceivers and a mobile-phone. Locally collected data arc encoded with a BCH error correcting code and transferred to a receiver through a RF module. The receiver-side RF module decodes the transferred data and then repetes them to a mobile-phone. Lastly, the mobile-phone hands over the data through a wireless phone network to a host computer in the internet.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.1
• /
• pp.60-63
• /
• 2009

In this paper, Designed and implemented about module that generate division signal for uplink section and downlink section for controlling Tx/Rx antenna of 2.3-2.7GHz WiMAX TDD repeater. It is consisted of RF block and Baseband block, and because function of this module is that synchronize with WiMAX signal and create division signal for uplink section and downlink section, this module was designed only received path. And because of manufacturing of most RF block by one chip, this module could minimize area. And in baseband block, used the WiMAX Modem to detect Preamble and DL-MAP information of WiMAX signal. This design can process about 2.3-2.7GHz WiMAX.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.776-779
• /
• 2004

A RF front-end module is designed for GIS(Gas Insulated Substation) which is employed for effective and efficient very high voltage transmission. Major advantage of the unit is improved PO detection sensitivity through minimizing the effect of surrounding interference signals, which is achieved by controlling the gain and the selection of the frequency band, for the precise detection of any UHF PO (Partial Discharge) disturbance occurred in the GIS due to some unwanted problems. For the development of the module, various switches for providing selected signal paths, wideband LNA, 3 BPF for selecting detection frequency band, and video detector are designed, fabricated and measured on 1 mm FR4 substrate with various RF components. The detection sensitivity of the unit was <-60 dBm that is sufficient to detect UHF PO signals as low as 1 pC. It is believed that the value is enough to detect the signal occurred in GIS.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.4
• /
• pp.16-21
• /
• 2016

In this paper, we have designed and fabricated a receiver module for 5.8GHz Microwave Wireless Power Transmission. The receiver module was composed of an antenna, BPF (Band Pass Filter) and RF-DC converter. The antenna was designed to RHCP (Right Hand Circular Polarization). And we used ${\lambda}g/2$ open-circuited stubs for the BPF. In addition, the RF-DC converter used the tripler voltage circuit for voltage multipliers. The integrated receiver RF module for 5.8GHz Microwave Wireless Power Transmission has been designed and fabricated. The voltage was measured to the distance of 50cm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1020-1027
• /
• 2005

In this paper, economic miniature RF transmitter module for intelligent transportation system(ITS) is described. This module which consists of ASK modulator, frequency synthesizer, power amplifier is operating at 5.8 GHz frequency band and implemented by using LTCC process technique. Thus, ultra small size of 0.8 CC and improved electrical performances has been obtained. From the test results, transmitting characteristics of 10 dBm ouput power and -46 dBc interchannel interference with 1.024 Mbps ASK modulated have been shown. Frequency synthesizer as a transmitting signal source reveals very short locking time of 26 usec and outstanding phase noise of -115 dBc/Hz at 1 MHz offset from 5.8 GHz center frequency.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.613-616
• /
• 2002

This paper has been studied an improvement of receive sensitivity for RF module of Industrial Scientific Medical(ISM) Band. In the paper, Also this paper handles receive sensitivity progress of RF module in ISM band. how to improve receive sensitivity adds to Surface Acoustic Wave(SAW) filter, Low Noise Filter(LNA), etc and insulates receiver and transmitter. And then the circuit is inspected by the effective range test of receiver and transmitter. And this Paper was designed that micro-controler controls the part of RF by software.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.3
• /
• pp.19-25
• /
• 2000

In this paper, we describe RF receiver module for IMT-2000 handset with 5 MHz channel bandwidth. The fabricated RF receiver module consists of Low Noise Amplifier, RF SAW filter, Down-converter, If SAW filter, AGC and PLL Synthesizer. The NF and IIP3 of LNA is 0.8 dB, 3 dBm at 2.14 GHz, conversion gain of down-converter is 10 dB, dynamic range of AGC is 80 dB, and phase noise of PLL is -100 dBc at 100 kHz. The receiver sensitivity is -110 dBm, adjacent channel selectivity is 48 dBm.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.2
• /
• pp.50-54
• /
• 2015

In this paper, we report on a high performance 94 GHz MMIC mixer module using 0.1-um metamorphic high electron mobility transistors (MHEMTs). A modified resistive mixer with a RF amplifier was proposed in this work for low conversion loss and high LO-RF isolation. The MMIC mixer module was fabricated using a MMIC chip and CPW-waveguide transitions. The fabricated mixer chip and module showed a low conversion loss of 6.3 dB and 9.5 dB, and LO-RF isolations of 24.8 and 30.4 dB at 94 GHz, respectively. This results are superior to those of previously W-band (75-110 GHz) MMIC mixers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.8
• /
• pp.958-966
• /
• 2012

This paper presents a compact bluetooth/WiFi dual-mode dual-band RF front-end module(FEM) is realized by low temperature co-fired ceramic(LTCC) technology. The proposed RF front-end module consists of a diplexer, baluns in the LTCC substrate, and an SPDT switch, an SP3T switch on the LTCC substrate. In order to reduce the module size and increase integration level, the proposed diplexer and balun are designed using LC lumped elements. The parasitic elements caused by coupling effect between metal pattern layers and ground plane layer are considered during the design. The fabricated dual-mode RF front-end module has 13 pattern layers including three inner ground layers and it occupies less than $3.0mm{\times}3.7mm{\times}0.66mm$.