• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3256-3258
• /
• 1999

Recently contactless ID system has emerged as new ID industry. It's called RF-ID. RF-ID is divided into active RF-ID and passive RF-ID. The passive RF-ID operates without battery and so has no limitation in its operating range and life time. But it needs the RF-OC conversion circuit. It also can be applied to batteryless sensor for many application. This paper presents the study of the RF-OC conversion circuit for batteryless system in high frequency and confirms it by simulation and experiment.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.2
• /
• pp.83-91
• /
• 2012

An RF energy detector for spectrum sensing in TV white space transceiver is presented. It is based on an RF active filtering technique that comprises a low-noise amplifier with a frequency-translation high-pass filtering feedfoward loop, which attenuates the unwanted sideband energy and only passes the wanted band energy. Unlike the conventional architecture, a new architecture that can attenuate both sidebands at the same time is proposed. A simplified system modeling method is presented to assess the non-ideality effects on the RF energy detector performances. System behavioral simulations demonstrate that the proposed architecture can be instrumental for realizaing a RF energy detector circuit in CMOS.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.8
• /
• pp.1392-1398
• /
• 2000

In this paper, Sub Harmonic Ring Mixer using Anti-Parallel Diode Pair is studied. Conventional mixers mix LO signal with RF signal and, obtain IF signal from the difference between LO and RF. Sub harmonic ring mixers using APDP mix RF signal with the second harmonic of LO signal, LO frequency needed for conventional receiver is reduced by 1/2.The produced mixer showed 12 dB conversion loss, and 1 dB compression point of IF signal, in respect to RF signal, was found at the 0 dBm RF signal. Isolation LO/IF and LO/RF is 24.6 dB and 22.5 dB respectively. Isolation RF/LO and LO/RF is 32.6 dB and 22.5 dB respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4891-4895
• /
• 2010

RF coil is an important component of the Magnetic Resonance Imaging (MRI) system and the performance of RF coil is one of major factors for high SNR images. Sensitivity and RF field uniformity are parameters for evaluating RF coil performance. Since the B1 field is induced by RF coil, MR signal is strongly affected by RF coil structure and arrangement. In receiving MR signal, the RF coil sensitivity to MR Signal is also determined by the induced B1 field of RF coil. Therefore, the spatial distribution of B1 field must be verified. In this work, we performed computer simulation of the basic RF coil structures using Matlab and verified their sensitivity and uniformity through their B1 field distribution. This work will be useful for the advanced multi-channel RF coil design.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.12
• /
• pp.560-566
• /
• 1986

In the design of an RF discharge system, the electrical equivalence of the gas discharge must be known. With this knowledge, one can design a suitable matching network for a maximum power transfer from the RF generator into the discharge. For this purpose, an experiment has been conducted in which the electrical impedance (conductance and capacitance) was determined as a function of power. In parallel with this, a detailed theoretical analysis has been done and the results are in accord with those of our experiment. Design equations are also given for a simple matching network, and a design example is presented to demonstrate its application. During the actual operation of an RF discharge system, however, it has been often observed that the reflected power tends to vary in small values due to the changes in the impedance of the system. This problem can be relieved by adding an automatic impedance matching circuit to the system and this paper presents such an automatic impedance matching network.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2203-2205
• /
• 2003

KIRAMS-13, the first medical cyclotron developed by domestic technique, is used to produce radio-isotope such as $^{18}F$ whose life time is relatively short through test operation. For high-power operation of charged particle accelerators, the power coupler must withstand enormous stresses due to charging induced by high RF power passing through. High-power RF testing with peak power in excess of 30kW has been performed on prototype power coupler for KIRAMS-13 normal conducting cavities. CST MICROWAVE STUDIO(CST MWS) is used for fundamental RF Design, and power coupler is manufactured according to fundamental power coupler design requisite. The qualification of the couplers has occurred for the time being only in a limited set of conditions as the available RF system and control instrumentation are under improvement.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.2
• /
• pp.100-106
• /
• 2024

To generate the plasma required in dry cleaning processes, the plasma chamber must be supplied with a high-quality AC voltage with a voltage of more than 1 kV and a frequency of 400 kHz. In the existing research, many methods to supply high power have been studied, but how to improve the quality of the power for high-quality plasma has been relatively little studied. In this paper, we propose a study to improve the quality of RF power circuit for high-quality plasma generation in dry cleaning method. Existing methods in the environment of full-bridge-based RF power circuits must perform PWM duty control in the light load region. This causes distortions in the waveform, resulting in poor power quality, which directly leads to poor plasma quality. To solve these problems, a half-bridge switching method is proposed and the improvement in waveform quality is verified. To verify the feasibility of the design and control algorithm proposed in this paper, an RF power circuit prototype is fabricated and the proposed design and control method is verified through simulation and actual experiments under dummy load.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.821-827
• /
• 2018

In devices used for re-forming osteoblasts to treat osteoporosis, a magnetic field is applied from the outside of the bone, and the minerals contained in the bone are aligned in a certain direction and undergo precessional motion. When a $90^{\circ}$ RF pulse is applied by using an RF coil, protons of minerals are brought to an excited state, and phosphorus activity promoting the deposition of osteoblasts in the bone is increased, thereby reshaping the bone. Miniaturizing the RF coil that generates a signal corresponding to the harmonic of the precessional motional frequency by means of the $90^{\circ}$ RF pulse can drastically reduce the overall size of the bone reshaping system. In this study, we propose a methodology for the miniaturization of the RF coil that can be used for osteoblast re-formation using a bone reshaping system. The capacitance of the designed RF coil is 25 pF, the inductance is approximately 100 nH, and the resonance frequency is 96 MHz. The radius of the end ring of the designed RF coil is 18 cm, and the total length of the leg is $2{\times}11.6cm$. The performance of the coil is verified through post-design measurement.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11A
• /
• pp.909-917
• /
• 2009

In this paper, we proposed and implemented the method to efficiently generate TDD synchronization signal and the digital circuit for the RF repeater which can eliminate the shadow region in the wireless communication field using the time division duplex (TDD) method. After detecting the TDD signal from the transmitted or received RF signal, the detected TDD signal is fed to the RF repeater for the normal operation. The proposed technique detects the envelop of the downlink signal and amplifies the detected envelop, and then restores the degraded envelop with the proposed digital filtering method. Finally the restored envelop is manipulated to the TDD synchronization signal. Our focus on the proposed algorithm is to develop it with simple feature and low cost but robust performance. The proposed scheme was implemented to the integrated system which has both RF and digital circuit and tested under the same condition with the commercial WiBro service.

• ETRI Journal
• /
• v.32 no.4
• /
• pp.503-511
• /
• 2010

WiBro radio frequency (RF) repeater is used for solving the problem of partial shadow areas in the wireless communication field that uses time-division duplexing (TDD) mode. In this paper, a method to efficiently generate TDD signals for WiBro RF repeater is proposed and its digital circuit is implemented. A TDD signal is detected from RF signals transmitted/received to/from RF repeater and then inputted again into the RF repeater, so that it can operate normally. First, the envelope of downlink signals is detected and then clamped to extract the basic form of a TDD signal using an operational amplifier circuit. Next, the TDD signal is generated by restoring and filtering the shape which has been distorted by the wireless channel. The algorithm and system to acquire TDD signal are developed with a goal to have simple but powerful functions with as little cost as possible. The proposed method is implemented as an RF-digital integrated system and verified through the experiments under the same condition as actual WiBro service environment.