• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 추계학술대회 논문집 학회본부
• /
• pp.380-383
• /
• 1990

When the MOSPET is applied as a switching device for the resonant inverter, a damped oscillating noise is appeared at specific frequency band. This damped Oscillation is caused by the series and parallel resonance due to distributed circuit parameter of snubber and main circuit. This paper describes the frequency-impedance characteristic of the resonant inverter and optimal snubber design strategy to reduce the RF noise.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.111-114
• /
• 2005

The isolation performance of the S-band single-pole single-throw (SPST) monolithic microwave integrated circuit (MMIC) switch with two different RF-interconnection approaches, microstrip and grounded coplanar waveguide (GCPW) lines, are investigated. On-to-off isolation is improved by 5.8 dB with the GCPW design compared with the microstrip design and additional improvement of 6.9dB is obtained with the coplanar wire-bond interconnection (CWBI) at 3.4 GHz. The measured insertion loss and third-order inter-modulation distortion (IMD3) are less than 2.43 dB over 2.5 CHz $\sim$ 4 GHz and greater than 64 dBc.

• 한국전기전자재료학회논문지
• /
• 제18권3호
• /
• pp.216-218
• /
• 2005

Planar spiral inductors on silicon substrates were optimally designed using MATLAB, which is a tool to perform numerical computations with matrices. The equivalent circuit parameters of the spiral inductors were extracted from the data measured from the spiral inductors fabricated using a 0.18 $\mu\textrm{m}$ RF CMOS process. The metal width, which is a critical design parameter, was optimized for the maximum quality factor with respect to the operating frequency.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.305-308
• /
• 2009

This paper presents the design and analysis of RF Front End for Wireless Heartbeat measurement System. In this work LNA, an inductor connected at the gate of the cascode transistor and capacitive cross-coupling are strategically combined to reduce the noise and the nonlinearity influences of the cascode transistors in a differential LNA. The Mixer is implemented by using the Gilbert-type configuration, cross pmos injection technique and the resonating technique for the tail capacitance. The resulting LNA achieves 1.26 dB NF, better than 1.88dB NF Typical Also Mixer resulting achieves 9.8dB at 100KHz.

• International journal of advanced smart convergence
• /
• 제6권3호
• /
• pp.38-44
• /
• 2017

Currently, wired gables have been installed or portable storage devices have been installed for data acquisition of flying drone. In this paper, we propose a technology to transmit data wirelessly by sensing information such as battery discharge value, acceleration, and temperature by attaching RF sensor to a drone. The purpose of this paper is to design and develop the monitoring technology of agriculture drone battery usage in real time using RF sensor. In this paper, we propose a monitoring system that can check real time data of battery changed value, temperature, and acceleration during pesticide control activity of agricultural drone.

• International Journal of Advanced Culture Technology
• /
• 제4권4호
• /
• pp.1-5
• /
• 2016

In this paper, we present the study on the proposed design of a real-time transmission of a video from the drone to broadcasting station (OBVan) by using F8L10D-N LoRa Module. Nowadays, LoRa technology is proved to be the mass of low cost, long range machine-to-machine connectivity. Particularly in the field of broadcasting and communication system, F8L10D-N LoRa RF Module spread spectrum technology with long transmission distance and strong penetrative ability that is double stronger than traditional FSK as well as PSK modulation scheme.

• 센서학회지
• /
• 제20권3호
• /
• pp.145-150
• /
• 2011

In this paper, we designed a tunable microstrip patch antenna using RF MEMS switches. The design and simulation of the antenna were performed using a high frequency structure simulator(HFSS). The antenna was designed for use in the ISM band and either operates at 2.4 GHz or 5.7 GHz achieving -10 dB return-loss bandwidths of 20 MHz and 180 MHz, respectively. In order to obtain high efficiency and improve the ease of integration, a high resistivity silicon(HRS) wafer on a glass substrate was used for the antenna. The antenna achieved high gains: 8 dB at 5.7 GHz and 1 dB at 2.4 GHz. The RF MEMS DC contact switches were simulated and analyzed using ANSYS software.

• Journal of Positioning, Navigation, and Timing
• /
• 제5권1호
• /
• pp.37-45
• /
• 2016

In this paper, design and implementation issues for a network-oriented RF emitter localization system with array antenna are discussed. For hardware, the problem of array mismatch and RF/IF channel mismatch are introduced and the calibration schemes for solving those problems are also provided. For software, it is explained how to overcome the drawback of conventional MUltiple Signal Identification and Classification (MUSIC) algorithm in a point of identifying the number of received signals and problems such as Data Association Problem and Ghost Node Problem in regard to multiple emitter localization are presented with some approaches for getting around those problems. Finally, for implementation, a criterion for arranging each of sensors and a requirement for alignment of array antenna' orientation are also given.

• Transactions on Electrical and Electronic Materials
• /
• 제17권1호
• /
• pp.7-12
• /
• 2016

This paper proposes a metal contact RF MEMS switch which utilizes a see-saw mechanism to acquire a switching action. The switch was built on a quartz substrate and involves vertical deflection of the beam under an applied actuation voltage of 5.46 volts over a signal line. The see-saw mechanism relieves much of the operation voltage required to actuate the switch. The switch has a stiff beam eliminating any stray mechanical forces. The switch has an excellent isolation of −90.9 dB (compared to − 58 dB in conventional designs ), the insertion of −0.2 dB, and a wide bandwidth of 88 GHz (compared to 40 GHz in conventional design ) making the switch suitable for wide band applications.

• Journal of Semiconductor Engineering
• /
• 제3권1호
• /
• pp.154-160
• /
• 2022

In this paper, we design a DC-DC boost converter with RF noise immunity to supply a stable positive output voltage for OLED displays. For RF noise immunity, an input voltage variation reduction circuit (IVVRC) is adopted to ensure display quality by reducing the undershoot and overshoot of output voltage. The boost converter for a positive voltage Vpos operates in the SPWM-PWM dual mode and has a dead-time controller using a dead-time detector, resulting in increased power efficiency. A chip was fabricated using a 0.18 um BCDMOS process. Measurement results show that power efficiency is 30% ~ 76% for load current range from 1 mA to 100 mA. The boost converter with the IVVRC has an overshoot of 6 mV and undershoot of 4 mV compared to a boost converter without that circuit with 18 mV and 20 mV, respectively.