• 한국통신학회논문지
• /
• 제30권4A호
• /
• pp.350-357
• /
• 2005

근거리무선통신 (Dedicated Short Range Communication, DSRC)은 지능형교통시스템 서비스 제공을 위한 통신 수단으로, 수 미터에서 수백 미터인 근거리 영역의 노변장치(Road Side Equipment, RSE)와 차량탑재장치(On-Board Equipment, OBE)와의 양방향 고속통신을 수행하는 통신시스템이다. 본 논문에서는 SiGe HBT 공정을 이용하여 근거리무선통신 송신기용 5.8 GHz 상향믹서를 설계 및 제작하였다. 설계된 상향믹서는 믹서코어 회로와 더불어 IF/LO/RF 입출력 정합 회로, IF/LO 입력 발룬 회로와 RF 출력 발룬 회로가 단일칩으로 구현되었다. 제작된 상향믹서는 $2.7 mm\times1.6mm$의 크기를 가지며, 3.5 dB의 전력변환이득과 -12.5 dBm의 OIP3, 42 dB의 LO to E isolation, 38 dB의 LO to RF isolation, 3.0 V의 공급전압 하에서 29 mA의 전류소모로 측정되었다.

• International Journal of Railway
• /
• 제3권2호
• /
• pp.39-45
• /
• 2010

The RF-CBTC (Radio Frequency-Communication Based Train Control) System is a communication system in railroad systems. The communication method of RF-CBTC system is the wireless between the wayside device and on-board device. The wayside device collects its location and speed from each train and transmits the distance from the forwarding train to the speed-limit position to it. The on-board device controlling device controls the speed optimum for the train. In the case of the RF-CBTC system used in Korea, transmission frequency is 2.4 [GHz]. It is the range of ISM(Industrial Scientific and Medical equipment) band and transmission of voice and data is performed by CDMA (Code Division Multiple Access) method. So noises are made in the AWGN (Additive White Gaussian Noise) and fading environment. Currently, the SNR (Signal to Noise Ratio) is about 20 [dB], so due to bit errors made by noises, transmission of reliable information to the train is not easy. Also, in the case that two tracks are put to a single direction, it is needed that two trains transmit reliable voice and data to a wayside device. But, by noises, it is not easy that just a train transmits reliable information. In this paper, we estimated the BER (Bit Error Rate) related to the SNR of voice and data transmission in the environment such as AWGN and fading from the RF-CBTC system using the CDMA method. Also, we supposed the SNR which is required to meet the BER standard for voice and data transmission. By increasing the processing gain that is a ratio of chip transmission to voice and data transmission, we made possible voice and data transmission from maximally two trains to a wayside device, and demonstrated it by using Matlab program.

• 한국항공우주학회지
• /
• 제50권11호
• /
• pp.801-807
• /
• 2022

본 논문에서는 초소형 S-대역 PCM/FM 텔레메트리 송신기를 제안한다. 크기의 소형화로 한정적인 공간에 적용이 가능하며 운용 환경 및 시스템마다 다르게 설정되는 규격에도 안정적인 데이터 송신이 가능한 장비를 설계 및 제작하였다. 장비의 소형화를 위하여 RF 직접변환 구조를 적용하였으며, 최소한의 소자로 송신기의 역할을 수행할 수 있도록 1장의 인쇄회로기판에 RF송신반, 전원분배반, 신호처리반을 구현하였다. 목표한 규격대로 성능의 저하 없이 S-대역(2,200~2,400MHz)에서 1~10W의 출력 가변이 가능하고 390kbps~12.5Mbps의 Data Rate 설정이 가능하도록 설계 및 제작을 진행하였다. 설계 검증을 위하여 장비를 제작한 후 RF 성능 시험 및 비트오류율 측정 시험을 진행하였다. 본 장비는 IRIG (Inter-Range Instrumentation Group) 표준이 제시하는 PCM/FM 변조 신호의 OBW(Occupied Bandwidth), null-to-null 대역폭, 1st IMD(Inter Modulation Distortion), Spurious Emission, Phase Noise 특성이 만족함을 확인하였으며, 송신기 점검 장비를 이용하여 본 장비가 전달받은 Data를 왜곡 없이 정상적으로 송신함을 확인하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.157.1-157
• /
• 2001

A new methodology is presented to diagnose faults in equipment plasma. This is accomplished by using neural networks as a pattern recognizer of radio frequency(rf) impedance match data. Using a realtime match monitor system, the match data were collected. The monitor system consisted mainly of a multifunction board and a signal flow diagram coded by Visual Designer. Plasma anomaly was effectively represented by electrical match positions. Twenty sets of fault-symptom patterns were experimentally simulated with experimental variations in process factors, which include rf source power, pressure, Ar and O$_2$ flow rates. As the inputs to neural networks, two means and standard deviations of positions were used ...

• 반도체디스플레이기술학회지
• /
• 제2권4호
• /
• pp.13-17
• /
• 2003

An adaptor is designed for chamber impedance measurement of plasma process. Copper rod, fixed board and compensation circuit are the major components of the adaptor. An adaptor can be to measure chamber impedance on time unless stopping a process and Data to measure can do the database. We can use it to a criteria data for a failure diagnosis. So developed adaptor could be used for diagnosis the plasma process chamber in semiconductor industry.

• IEIE Transactions on Smart Processing and Computing
• /
• 제3권4호
• /
• pp.221-225
• /
• 2014

Low power RF devices, such as RFID and Zigbee, are important for ubiquitous sensing. These devices, however, are powered by portable energy sources, such as batteries, which limits their use. To mitigate this problem, this study developed RF energy harvesting with W-CDMA for a low power RF device. Diodes are required with a low turn on voltage because the diode threshold is larger than the received peak voltage of the rectifying antenna (rectenna). Therefore, a Schottky diode HSMS-286 was used. A prototype of RF energy harvesting device showed the maximum gain of 5.8dBi for the W-CDMA signal. The 16 patch antennas were manufactured with a 10 dielectric constant PTFT board. In low power RF devices, the transmitter requires a step-up voltage of 2.5~5V with up to 35 mA. To meet this requirement, the Texas Instruments TPS61220 was used as a low input voltage step-up converter. From the evaluated result, the achievable incident power of the rectenna at 926mV to operate Zigbee can be obtained within a distance of 12m.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.449-452
• /
• 2005

For home networking system with a function of air quality monitoring, a wireless sensor module with several air quality monitoring sensors was developed for indoor environment monitoring system in home networking. The module has various enlargements for various kinds of sensors such as humidity sensor, temperature sensor, CO2 sensor, flying dust sensor, and etc. The developed wireless module is very convenient to be installed on the wall of a room or office, and the sensors in the module can be easily replaced due to well designed module structure and RF connection method. To reduce the system cost, only one RF transmission block was used for sensors' signal transmission to 8051 microcontroller board in time sharing method. In this home networking system, various indoor environmental parameters could be monitored in real time from RF wireless sensor module. Indoor vision was transferred to client PC or PDA from surveillance camera installed indoor or desired site. Web server using Oracle DB was used for saving the visions by web-camera and various data from wireless sensor module.

• 한국인터넷방송통신학회논문지
• /
• 제21권5호
• /
• pp.161-166
• /
• 2021

적외선 영상 시스템으로 야외에서 다양한 영상에 대하여 테스트를 할 때 테스트 한 영상을 저장하여 비교확인이 필요하다. 야외에서 시험을 하기 때문에 휴대성이 간편해야 하며 장시간의 영상을 저장하여야 하기 때문에 많은 저장공간이 필요로 한다. 또한 시험 이후에 쉽게 PC와 접속하여 저장된 데이터를 다운로드 받을 수 있어야 한다. 최근 메모리 시스템의 발전으로 쉽게 On Board 형태로 사용할 수 있는 eMMC 메모리를 활용하여 야외시험용 적외선 영상 저장보드를 설계할 수 있다. 본 논문에서는 적외선 영상을 쉽게 저장하고 다운받을 수 있는 휴대가 간편한 영상 저장보드 설계에 대하여 설명하고 PC와 접속하여 저장된 영상을 다운 받을 수 있는 GUI 프로그램에 대하여 설명한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1067-1070
• /
• 2003

In this paper, we present a remote measurement system for the wireless monitoring of ECU Sensor Signals of vehicle. In order to measure the ECU sensor signals, the interface circuit is designed to communicate ECU and designed terminal wirelessly according to the ISO, SAE regulation of communication protocol standard. A micro-controller 80C196KC is used for communicating ECU sensor signals. ECU sensor signals are transmitted to the RF-wireless terminal that was developed using the micro controller 80386EX. LCD, and RF-module. 80386EX software is programmed to monitor the ECU sensor signals using the Borland C++ compiler in which the half duplex method was used for the RS232 communication. The algorithms for measuring the ECU sensor signals are verified to monitor ECU state. At the same time, the information to fix the vehicle's problem can be shown on the developed monitoring software. The possibility for remote measurement of ECU sensor signals using 80386EX is also verified through the developed systems and algorithms.

• 전자공학회논문지
• /
• 제52권1호
• /
• pp.175-181
• /
• 2015

본 논문에서는 무선 LAN을 기반으로 u-Hospital 서비스를 지원할 수 있는 임베디드 리눅스 기반의 2.4GHz ISM 대역용 플랫폼 시제품을 개발하였다. 개발된 시스템은 ARM920T 프로세서 보드와 FPGA 보드가 서로 연동되게 설계되었고, 무선 접속을 위해 IEEE 802.11b PHY 보드, AD/DA(10Bit), 그리고 RF(2.4GHz) 보드가 연결되도록 설계하였으며, 임베디드 리눅스를 탑재하여 IEEE 802.11b/g Access Point(Option: IEEE 802.11a/b/g) 시험이 가능하여 임베디드 시스템 설계에 응용될 수 있다. 또한 개발된 시스템은 무선 접속 기술과 Modem(OFDM etc) 및 IP(Intellectual Property) 회로를 시험하고 검증할 수 있으며, 홈&모바일 헬스 케어 및 웰 니스 서비스로의 응용 확장이 가능하다.