• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2052-2054
• /
• 2004

The TX/RX broadband L-type circular polarization antenna using LTCC at K/Ka band has been presented. This antenna has been analyzed in compensation for LTCC with relative permittivity 5.2 and could have been integrated with RF component. As the measured 10dB impedance circular polarization bandwidth of the proposed antenna is 7%(20.8GHz${\sim}$22.2GHz) at the K band and 2.3%(30.9GHz to 31.6GHz) at the Ka band. Also the gain of the antenna is -0.7${\sim}$3.05dBi at the K band and -2.8${\sim}$1dBi at the Ka band. The purpose of the research is to design an efficient antenna structure for satellite communication at K/Ka band. the antenna should be used for both TX and RX frequency bands. The antenna will be mounted on LTCC(Low Temperature Co-fired Ceramic) so that it can be integrated with other RF circuits. This research is important because of the following reasons. 1) The frequency ranges of satellite communication tends to move up to higher frequency such as Ka band or milimeter wave band. 2) Design of antenna for smaller size, lighter weight and less loss is preferred by most RF engineers. 3) Antennas on LTCC enables to integrate the antenna with other RF circuits, and thus, one can reduce the size and loss of the RF system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1113-1119
• /
• 2013

In this letter, a new approach is proposed for the design of a multi antenna for MIMO wireless devices. The proposed antenna covers various LTE(Long Term Evolution) service bands: band 17(704~746 MHz), band 13(746~787 MHz), band 5(824~894 MHz), and band 8(880~960 MHz). The proposed main antenna consists of a conventional monopole antenna with an inverted L-shaped slit for wideband operation. The proposed the LTE sub antenna is based on a switch loaded loop antenna structure, with a resonance frequency that can be controlled by capacitance of a logic circuit. The tuning technique for the LTE Rx antenna uses a RF MEMS(Micro-Electro mechanical system) to match the impedances to realize the bands of interest. Because the two proposed antennas are polarized orthogonally to each other, the ECC(Envelope Correlation Coefficient) characteristic between two antennas was measured to be very low (below 0.06) with an isolation characteristic below -20 dB between the two antennas in the operating overall LTE bands. The proposed antenna is particularly attractive for mobile devices that integrate LTE multiple systems.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.129-129
• /
• 2009

In this paper, a tunable microstrip patch antenna designed using RF MEMS switches is reported. The design and simulation antenna were performed using high frequency structure simulator (HFSS). The antenna was designed in ISM Band and operates simultaneously at 2.4 GHz and 5.7 GHz with a -10 dB return-loss bandwidth of 20 MHz and 180 MHz, respect-tively. To obtain high efficiency and improve integrated ability, the High Resistivity Silicon (HRS) wafer was used for the antenna. The antenna achieved high gain with 8 dB at 5.7 GHzand 1.5 dB at 2.4 GHz. The RF MEMS DC contact switches was simulated and analysis by ANSYS software.

• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.145-150
• /
• 2011

In this paper, we designed a tunable microstrip patch antenna using RF MEMS switches. The design and simulation of the antenna were performed using a high frequency structure simulator(HFSS). The antenna was designed for use in the ISM band and either operates at 2.4 GHz or 5.7 GHz achieving -10 dB return-loss bandwidths of 20 MHz and 180 MHz, respectively. In order to obtain high efficiency and improve the ease of integration, a high resistivity silicon(HRS) wafer on a glass substrate was used for the antenna. The antenna achieved high gains: 8 dB at 5.7 GHz and 1 dB at 2.4 GHz. The RF MEMS DC contact switches were simulated and analyzed using ANSYS software.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.6 s.121
• /
• pp.648-655
• /
• 2007

In this paper, we introduce a dual coil antenna which is useful for reducing the effects of radio frequency noise in an RFID system. A dual coil antenna is composed of two identical coils that are connected in series. The noise voltages in the two coils almost disappear when they are added because the magnitudes are equal and the polarities are opposite. The noise in an RFID reader with a dual coil antenna was 15 dB lower than that with a single coil antenna.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.10
• /
• pp.885-892
• /
• 2013

The main advantage of ESPAR antenna is that ESPAR antenna requires only a single RF chain for reduction of transceiver's hardware complexity, as compared to conventional MIMO system. In conventional MIMO system, each data symbol is mapped to each antenna. But, each data symbol is mapped to each orthogonal basis pattern in ESPAR antenna system. In this paper, we design beamspace MIMO system using ESPAR antenna with single RF chain for MIMO system of low-complexity and low power consumption. And then, we analyze performance of beamspace MIMO according to each PSK modulation. Performance of beamspace MIMO system is similar to performance of conventional MIMO system. As a result of analyzing the performance of beamspace MIMO system using higher-order PSK modulation. we can confirm that performance characteristic of beamspace MIMO system with low complexity and low power consumption is similar to digital communication of signal domain.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.5
• /
• pp.220-228
• /
• 2014

ESPAR(Electronically Steerable Parasitic Array Radiator) antenna is the technique for overcoming the problems of space limitation and energy efficiency due to the multiple RF-chain. Conventional MIMO system with multiple antenna requires a large number of RF-chain for transmitting the multiple data because it transmits the data in proportion to the number of antenna. Beamspace MIMO system using the ESPAR antenna which has single RF-chain was proposed for solving the problems caused by using the multiple antenna and RF-chain. In this paper, therefore we propose 2x2 beamspace MIMO system using the 16, 64-QAM modulation and evaluate the performance of this system to reveal that it is possible that beamspace MIMO system can use not only PSK modulation but also QAM modulation. We confirm that QAM symbol can be generated by adjusting reactance of parasitic elements and making reactance set and also we confirm that performance of beamspace MIMO system is similar to the conventional MIMO system by transmitting the QAM symbol made by reactance set through the simulation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.8
• /
• pp.79-85
• /
• 2004

In this paper, the RF-ID system for ubiquitous tagging applications has been designed, fabricated and analysed. The RF-ID System consists of passive RF-ID Tag and Reader. The passive RF-ID tag consists of rectifier using zero-bias schottky diode which converts RF power into DC power, ID chip, ASK modulator using bipolar transistor and slot loop antenna. We suggest an ASK undulation method using a bipolar transistor to compensate the disadvantage of the conventional PIN diode, which needs large current Also, the slot loop antenna with wider bandwidth than that of the conventional patch antenna is suggested The RF-ID reader consist of patch array antenna, Tx/Rx part and ASK demodulator. We have designed the RF-ID System using EM and circuit simulation tools. According to the measured results, The power level of modulation signal at 1 m from passive RF-ID Tag is -46.76 dBm and frequency of it is 57.2 KHz. The transmitting power of RF-ID reader was 500 mW

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.4
• /
• pp.485-491
• /
• 2014

An Antenna & RF system for a fly-away satcom terminal application on ka-band is presented in this paper. The Fly-away satellite terminal can be moved and operated by two person and adapt automatic satellite tracking system in order to decrease the tracking time. Additionally, for low-power consumption, compact size and light-weight, a dual reflector antenna is constructed using dual-offset gregorian antenna structure. For minimize weight, the reflector of the antenna is made of Magnesium. For low-power consumption and light-weight, the pHEMT MMIC compound devices is utilized. The Electronic Band-Gap(EBG) Low-Pass Filter(LPF) is designed for harmonic rejection. In the receiving part, Low-Noise Block converter(LNB) structure is designed for compact and lightweight. In this paper, fly-away satcom terminal with low-power consumption, compact size and light-weight is described with antenna system and RF system performances. Through the experimentation, fly-away terminal's EIRP is more than 50dBW, G/T is more than $17dB/^{\circ}K$.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.593-600
• /
• 2020

The equipment for marine IoT service have to overcome the effect of seawater. Furthermore, the free floating transmitter in seawater will be less affected by the seawater environment. The results of the design and fabrication of antenna, which is embedded in buoy, are shown in this research. The proposed antenna is used to supervise the states of fishing gears in monitoring system for real-name system of electric fishing gear. The selected frequency band of the proposed antenna is 920 MHz, and PCB pattern type is selected for subminiature and light weight. It is confirmed that RF characteristics is more degraded, however, the radiation is gradually upward as the contact surface of buoy with seawater is more broaden through the simulation results. That is, the RF performance of the proposed antenna is more deteriorated but beam radiation characteristics is more suited the marine IoT, the seawater effect is more increased. It is expected that the proposed antenna will contribute the implementation of IoT network based on low power wide area (LPWA) when the degradation of RF performance will be settled.