• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.360.2-360.2
• /
• 2016

CuSn thin films were fabricated by rf magnetron co-sputtering method on the Si(100) substrate for evaluation of the antibacterial effect. The co-sputtering process was performed with different rf powers and sputtering times to regulate the thickness of the films and relative atomic ratio of Cu to Sn. The physicochemical properties of the CuSn thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray induced Auger electron spectroscopy (XAES), Optical microscope (OM), 4-point probe, and antibacterial test. An antibacterial test was conducted with Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) as changing contact times between CuSn fillms and bacteria suspension. We compared to the crystalline structures of films before sterilization and after sterilization by XRD measurement. The changes of oxidation states of Cu and Sn and the chemical environment of films before and after antibacterial test were investigated with high resolution XPS spectra in the regions of Cu 2p, Cu LMM, and Sn 3d. After antibacterial test, the morphology of the films was checked with an OM images. The electrical properties of the CuSn films such as surface resistance and conductivity were measured by using 4-point probe.

• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.227-233
• /
• 1994

The Bi-Sr-Ca-Cu-O thin films were deposited by RF-magnetron sputtering method on Si(P-111) wafer without a buffer layer and annealed at various temperatures in oxygen atmosphere. The temperature dependence of electrical resistance, the microstructure of intermediate phase, and the surface morphology of films were examined by four probe method, XRD, and SEM, respectively. The chemical composition and the depth profile of the films were determined by ESCA spectra. Thin films annealed at $600^{\circ}C$ and $700^{\circ}C$ in oxygen atmosphere showed onset temperatures of 90 K and 85K, and Tc(zero) of 22K and 31K, respectively. The sample annealed at $700^{\circ}C$ had the highest volume fraction of superconducting phase and showed smooth microsturcture. In ESCA spectra, the thin films were homogeneous with depth.

• Applied Science and Convergence Technology
• /
• v.26 no.2
• /
• pp.30-33
• /
• 2017

ZnO thin films which were deposited by RF magnetron sputtering system were annealed by furnace and insitu heat treatment methods. We investigated the effect of heat treatment method on physical properties of ZnO thin films. The structural and optical properties of ZnO thin films were improved by heat treatment. Through the annealing treatment of ZnO film by furnace, the good crystallinity and ultraviolet emission were obtained. These results are attributed to the improved formation of Zn-O bond in ZnO thin film annealed at by furnace. We confirm that the formation of Zn-O bond plays an important role in obtaining the excellent structural and optical properties of ZnO thin films.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.212-214
• /
• 1994

At recent time, superconducting technology makes it possible to develop various devices using strong magnetic fields. As increasing with devices using high magnetic fields, magnetic shielding technology is essential in order to get high efficiency. Therefore it is necessary to establish production method and clear characteristics of suitable shielding materials. Usually, ferromagnetic metal has been used for shielding of high magnetic fields up to the present time. Instead of heavy ferromagnetic metal, we can acquire better upgraded shielding system by using of very light superconducting thin film that has a perfect diamagnetism. We would like to study basic characteristics of NbTi thin film produced by RF sputtering, investigated morphology and crystal structure of NbTi thin film by SEM and XRD, identified superconductivity measuring by critical current.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.22-25
• /
• 1995

In this paper, the physical characteristics of piezoelectric transducer which generates acoustic weve at microwave frequency were theoretically analized. We found that increasing electrode thickness is showed large distorthion on bandwidth. ZnO thin film were desposited by RF magnetron sputtering method. considering the sputtering parameters. Thickness of the desposited ZnO was 3.9 $\mu\textrm{m}$. In this experiment, we get that resistivity is 12.196${\times}$109 [cm$\Omega$], that resonance frequency is 827.47MHz Measuring insertion loss, we ascertained to possibility of transducer application for microwave frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.107-108
• /
• 2006

ZnO is a promising material for UV or blue LEDs p-Type ZnO thin films which are imperative for the p-n junction of LEDs are difficult to achieve because of strong compensation of intrinsic defects such as zinc interstitial and oxygen vacancy. The method of codoping group three elements and group five elements is effective for the realization of p-type ZnO films. In this study, We codoped N and Al m ZnO thin films by RF magnetron sputtering and annealed the films in sputtering chamber. Some films showed p-type conductivity m Seeback effect measurement.

• Corrosion Science and Technology
• /
• v.3 no.4
• /
• pp.148-153
• /
• 2004

Magnesium thin flims were prepared on cold-rolled steel substrates by RF magnetron sputtering technique. The influence of argon gas pressure and substrate bias voltage on their crystal orientation and morphology of the coated films were investigated by scanning electron microscopy (SEM) and X-ray diffraction, respectively. And the effect of crystal orientation and morphology of magnesium films on corrosion behaviors was estimated by measuring anodic polarization curves in deaerated 3%NaCl solution. From the experimental results, all the sputtered magnesium films showed obviously good corrosion resistance to compare with 99.99% magnesium target of the sputter-evaporation metal. Finally it was shown that the Corrosion-resistance of magnesium films can be improved greatly by controlling the crystal orientation and morphology with effective use of the plasma sputtering technique.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.527-534
• /
• 1998

Thin film deposition of InN, which is a less-studied III-nitride compound semiconductor because of the difficulty if crystal growth, was performed by rf reactive sputtering method using In target and $N_2$reactive gas. The structrual, electrical, and optical properties of the produced films were measured and disussed according to the sputtering parameters such as deposition pressure, rf power, and substrate temperature. From the result of deposition pressure, rf power, and substrate temperature, we could obtain optimal conditions of 5m Torr, 60W, $60^{\circ}C$ for preparing InN thin film with high crystallinity, low carrier concentration, and high Hall mobility. The carrier concentration, Hall mobility, and optical bandgap of the fabricated InN thin films at optimal condition were $6.242\times10^{18}cm^{-3}, 212.526cm^2/V\cdot$ｓ, and 1.912eV, respectively.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.27-32
• /
• 2020

CuS thin films were deposited on glass substrates at room temperature by RF magnetron sputtering. The structural and optical properties of CuS thin films grown by varying RF-power from 40 W to 100 W were studied. From the XRD analysis, we confirmed hexagonal crystal structures grown in the preferred orientation of the (110) plane in all CuS thin films, and the intensity of the main diffraction peak increased in proportion to the increase of RF-power. In the case of CuS thin film deposited at 40W, small-sized particles formed a thin and dense surface morphology with narrow pore spacing, relatively. As the power increased, the grain size and grain boundary spacing increased sequentially. The peaks for the binding energy of Cu 2p_3/2 and Cu 2p_1/2 were determined at 932.1 eV and 952.0 eV, respectively. The difference in binding energy for the Cu²⁺ states was the same at 19.9 eV regardless of process parameters. The transmittance and band gap energy in the visible region tended to decrease with increasing sputtering powers.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.4
• /
• pp.6-8
• /
• 2008

$Y_{2}O_{3}$ nanodots have been deposited on top of the substrate surface using rf-sputtering method. This approach was adopted to be able to modulate the substrate surface with nanodots used as a seed for the flux pinning sites in the superconducting films. The nanodot density of $Y_{2}O_{3}$ was controlled mainly using the deposition time, rf-power, and substrate temperature. $Y_{2}O_{3}$ nanodots with ${\sim}\;50\;nm$ in diameter and ${\sim}\;3\;nm$ in height were obtained at rf-sputtering time of about 15 seconds using 400 watts of rf-power and $630^{\circ}C$ of substrate temperature. As deposition time increased up to about 30 seconds, the interconnected islands of $Y_{2}O_{3}$ nanodots formed, which can be clearly observed with AFM surface image. The substrate surface was covered entirely with $Y_{2}O_{3}$ layer above the deposition time of 60 seconds. The modulated surface morphologies and cross section analysis of deposited $Y_{2}O_{3}$ nanodots at various experimental conditions have been examined using AFM and discussed with respect to the flux pinning sites for the practical application.