• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.7
• /
• pp.24-30
• /
• 2000

In this paper, we proposed an fiber-optic transceivers based on the analog optical transmission techniques of incorporating the SCM (subcarrier multiplexing) and WDM (wavelength-division multiplexing ) method, which can be used to transmission of IMT-2000 and PCS wireless frequency band and analyzed overall those parameters related with fabrication. Especially in the impedance matching network between RF signal and LD, we proposed the method of deriving optimal performance using simulation techniques. In the frequency band of 1.7GHz∼2.25GHz, experimental data for the gain flatness and the noise floor of the optical link were also presented $\pm$1.5dB and -130dBm respectively when the link Rain was 0dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.1B
• /
• pp.56-65
• /
• 2002

This paper proposes a novel transmit diversity technique, namely symbol split orthogonal transmit diversity (SS-OTD). In this technique, full path diversity and temporal diversity are achieved by combining orthogonal transmit diversity technique (OTD) technique with the symbol splitting method proposed by Meyer. Its performances is simulated for fundamental channels associated with the forward link of the IS-2000 system, and then compared with those of OTD and space-time spreading (STS). Our proposed method offers a 0.5-7.7dB performance improvement over OTD under various simulation environments and its performance is similar to STS. Moreover, compares with that of STS, the peak-to-average power ratio (PAR) of transmitted signals in SS-OTD is reduced by a maximal 1.35dB, which decreases the complexity of base station RF devices, such as power amplifiers. Thus, SS-OTD is comparable to STS in performance and superior to STS in the cost and efficiency of base station RF devices.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1281-1283
• /
• 1995

In this paper, we develop a prototype of the Optical SCM transmission module. This module is possible to application to electric facilities for control and measurements. Transmission channel number is two channels, namely, image and digital signal. In the image transmission, modulation method is AM, baseband signal is NTSC video signal and demodulation use PLL. Modulation of digital signal is QPSK, 1.544Mbps and demodulation use PLL. First, we calculate theoretical analysis about RF and Optical link in the transmission. This calculation is well correspond with practical system and transmission experiment is excellent, but this is only two channel model. And now, we plan to multichannel transmission to measure intermodulation, frequency assignments and optimal channel numbers et al.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.386-396
• /
• 2013

A 10-Gbit/s wireless communication system operating at a carrier frequency of 300 GHz is presented. The modulation scheme is amplitude shift keying in incoherent mode with a high intermediate frequency (IF) of 30 GHz and a bandwidth of 20 GHz for transmitting a 10-Gbit/s baseband (BB) data signal. A single sideband transmission is implemented using a waveguide-tapered 270-GHz high-pass filter with a lower sideband rejection of around 60 dB. This paper presents an all-electronic design of a terahertz communication system, including the major modules of the BB and IF band as well as the RF modules. The wireless link shows that, aided by a clock and data recovery circuit, it can receive $2^7$-1 pseudorandom binary sequence data without error at up to 10 Gbit/s for over 1.2 m using collimating lenses, where the transmitted power is 10 ${\mu}W$.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.45-49
• /
• 2003

Wireless life signal detecting system is implemented with using the mechanism of Doppler Effect. This system can measure the respiration and heart rates with the periodic movement of skin and muscle near the heart. The system is consisted of antenna, RF transmitter, receiver, and display part. We did use two operating frequencies at 1.9 ㎓ and 10 ㎓. Firstly, the link budget about detecting system is analyzed and the signal detected from the system is compared with electrocardiogram(ECG) of monitor which is using for patient monitoring in hospital. Secondly, the detection of vital sign is also performed according to the different distances, and including behind the wall.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.1
• /
• pp.74-81
• /
• 2004

We propose a novel scheme to transmit high center frequency RF signals using electroabsorption devices (EADs) as frequency converters at the transmitter and the receiver. In this approach frequency heterodyning is employed for obtaining high center frequency. With the EAD as a detector/mixer at the receiver we demonstrated a smaller conversion loss than that of the conventional modulator/mixer. With EAD as a modulator/mixer at the transmitter and with two heterodyned lasers to generate an optical local oscillator (LO), we demonstrated a large reduction (${\sim}23dB$) in conversion loss, and the transmission is not limited by the optical saturation of the EAD. This transmission scheme has optical single-side-band transmission feature which greatly relieves the fiber dispersion effect.

• Journal of Information Processing Systems
• /
• v.7 no.1
• /
• pp.43-52
• /
• 2011

Whether it is crosstalk, harmonics, or in-band operation of wireless technologies, interference between a reference system and a host of offenders is virtually unavoidable. In past contributions, a benchmark has been established and considered for coexistence analysis with a number of technologies including FWA, UMTS, and WiMAX. However, the previously presented model does not take into account the mobility factor of the reference node in addition to a number of interdependent requirements regarding the link direction, channel state, data rate and system factors; hence limiting its applicability for the MBWA (IEEE 802.20) standard. Thus, over diverse modes, in this correspondence we analytically derived the greatest aggregate interference level tolerated for high-fidelity transmission tailored specifically for the MBWA standard. Our results, in the form of benchmark indicators, should be of particular interest to peers analyzing and researching RF coexistence scenarios with this new protocol.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.63-64
• /
• 2006

Recently, researches for high-speed optical devices have been increased to provide mass data transmission and high-speed optical communication. Optical modulator in the transmission link is one of the crucial devices in total optical network system and it can affect a great effect to the whole transmission properties. In this paper, traveling wave electro-absorption modulator (TWEAM) is examined to ensure high efficiency in the RF range and wide bandwidth. In addition, the temperature-dependence electrical characteristics of TWEAM is investigated. Temperature dependent property variations were characterized using I-V and C-V measurement.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.303-308
• /
• 2008

Directly modulated fiber-optic links generally suffer higher link loss and larger signal distortion than externally modulated links. These result from the electron-photon conversion loss and laser modulation dynamics. As a method to overcome the drawbacks, we have experimentally demonstrated the RF performance of directly modulated, ultra-strong injection-locked gain-lever distributed Bragg reflector (DBR) lasers. The free-running DBR lasers exhibit an improved amplitude modulation efficiency of 12.4 dB under gain-lever modulation at the expense of linearity. By combining gain-lever modulation with ultra-strong optical injection locking, we can gain the benefits of both improved modulation efficiency from the gain-lever effect, plus improved linearity from injection locking. Using an injection ratio of R=11 dB, a 23.4-dB improvement in amplitude response and an 18-dB improvement in spurious-free dynamic range have been achieved.

• Journal of Positioning, Navigation, and Timing
• /
• v.8 no.1
• /
• pp.1-12
• /
• 2019

In this paper, we implement a navigation software of a Global Navigation Satellite System (GNSS) receiver based on a commercial purpose GNSS software receiver platform and verify its performance by performing experimental tests for various GNSS signals available in Korea region. The SX3, employed in this paper, is composed of an application program and a Radio Frequency (RF) frontend, and can capture and process multi-constellation and multi-frequency GNSS signals. All the signal processing procedure of SX3 is accessible by the receiver software designer. In particular for an easy research and development, the Application Programing Interface (API) of the SX3 has a flexible architecture to upgrade or change the existing software program, equipped with a real-time monitoring function to monitor all the API executions. Users can easily apply and experiment with the developed algorithms using a form of Dynamic Link Library (DLL) files. Thus, by utilizing this flexible architecture, the cost and effort to develop a GNSS receiver can be greatly reduced.