• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.545-554
• /
• 2003

Design of the optical modulator composed of a three-waveguide coupler and CPW traveling-wave electrodes was carried out. Switching phenomena of three-waveguide couplers were analyzed by using the coupled mode theory, and the coupling-lengths of the devices were calculated by means of the FDM. CPW traveling-wave electrodes were analysed by the CMM and SOR simulation technique in order to find the conditions of phase-velocity and impedance matching. Traveling-wave modulators were fabricated on z-cut LiNbO$_3$ substrate. Ti was in-diffused in LiNbO$_3$ to make waveguides and Au electrodes were built on the waveguides by the electrolyte technique. The fabricated modulator chip was end-polished, pig-tailed and packaged in a brass mount with K-connector. The insertion loss and the switching voltage of the optical modulator were about 4㏈ and 19V, respectively. Network analyzer was used to obtain the S parameter and the corresponding RF response. From the measurement, parameters of the traveling-wave electrodes were extracted to be Z$_{c}$= 45 Ω, N$_{eff}$=2.20, and $\alpha$$_{0}$=0.055/cm√GHZ. The measured optical response R($\omega$) was compared with the theoretically estimated one, showing both responses agree well. The measurement results revealed that 3㏈ bandwidth turned out to be about 13 GHz.

• Journal of Advanced Navigation Technology
• /
• v.21 no.1
• /
• pp.66-71
• /
• 2017

This paper describes implementation of a 165 MHz, 5 kW RF high power amplifier (HPA) for particle accelerator applications. The HPA consists of a drive amplifier for main amplifiers driving, sixteen 600 W class-AB push-pull power amplifier pallets and Wilkinson power divider/combiner using lumped LC components, which are divided/combined power amplifier pallet outputs. To detected the amplifier circuit of normal and reflected output power conditions, we used a bidirectional coupler. To radiate heat of main power amplifier, we were used an water-cooled copper plates to go through a water for radiation of heat. The HPA of center frequency 165 MHz has archived an efficiency of 62.5 % at 5 kW of power level experimentally.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.4
• /
• pp.1-9
• /
• 2007

Linearity is the one of the most important features for analog-optic transmission system. In our research, the available bandwidth for the feed-forward compensation circuit is enhanced by using a 180 hybrid coupler in the circuit. The bandwidth having the decreased 3rd-order intermodulation distortion(IMD3) over 10 dB is extended over 200 MHz with the center frequency of 1.6 GHz. We performed an efficient bandwith measurement for the feed-forward compensation system, which uses the network analyzer instead of the traditional measuring system that uses two RF signal generators and the spectrum analyzer. We identify the usefulness of this method from experimental results. In this study, we used cheap digital-purpose laser diodes for economical aspect, which proves the efficiency of the proposed analog system. The spurious-free dynamic range is improved about 6 dB/Hz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.29-35
• /
• 2016

We have demonstrated a $Ti:LiNbO_3$ electro-optic electric-field sensors utilizing a $1{\times}2$ Y-fed balanced-bridge Mach-Zehnder interferometric (YBB-MZI) modulator which uses a 3-dB directional coupler at the output and dipole patch antenna. The operation and design were proved by the BPM simulation. A dc switching voltage of ~16.6 V and an extinction ratio of ~14.7 dB are observed at a wavelength of $1.3{\mu}m$. For a 20 dBm rf power, the minimum detectable electric-fields are ~1.12 V/m and ~3.3 V/m corresponding to a dynamic range of about ~22 dB and ~18 dB at frequencies 10 MHz and 50 MHz, respectively. The sensors exhibit almost linear response for the applied electric-field intensity from 0.29 V/m to 29.8 V/m.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.9
• /
• pp.1064-1069
• /
• 2007

This paper proposes the highly miniaturized active $90^{\circ} power combiner for application to MMIC. Conventional passive $90^{\circ} power combiners can't be integrated on MMIC because of their very larger size. Therefore, the highly miniaturized $90^{\circ} power combiners are required for a development of highly integrated MMIC. For this paper, the highly miniaturized active $90^{\circ} power combiner employing InGaP/GaAs HBT was fabricated on GaAs substrate for application to highly integrated MMIC. A size of fabricated active $90^{\circ} power combiner was $2.42{\times}1.05$ mm, which was 2.2 % of conventional passive $90^{\circ} power combiner. The fabricated active $90^{\circ} power combiner showed a gain characteristic about 10 dB and a good phase-difference coupling characteristic of $-92.6^{\circ} than conventional passive $90^{\circ} power combiner at 2.4 GHz. The highly miniaturized active $90^{\circ} power combiner exhibited good RF performances comparable to conventional passive $90^{\circ} power combiners. This work is the first report of an active $90^{\circ} power combiner.