• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.19-26
• /
• 1998

In this paper, we studied the design and implementation of fading compensation systems at aspects of narrowband mobile communication using TTIB SSB. The mobile radio channel with multipath fading places fundamental limitations on the performance of wireless communication systems. The multipath fading is compensated using pilot tone in TTIB SSB. The TTIB transceiver was implemented using the prevailing digital signal processing (DSP) techniques and compensation for the multipath fading was incorporated in the receiver in the form of DSP algorithm. In order to evaluate fading compensation performance in TTIB transceiver, we first used computer simulation. In the simulation results, we found that the TTIB transceiver could compensate for the multipath fading as expected. Second, we carried out some experiments on TTIB transceiver implementation with DSP boards and later with hardwares including RF circuits with center frequency of 145MHz. Through these experiments, we found that fading compensation performance in TTIB transceiver was almost as good as that obtained from simulation.

• Journal of Korean Society for Geospatial Information Science
• /
• v.16 no.3
• /
• pp.43-49
• /
• 2008

The Real Time Location System (RTLS) is very important in the ubiquitous society for real time tracking of men, high price assets, and logistics products. In this work, we developed an active RF system for RTLS and tested its performance. The RTLS system developed in this work was constructed of three active readers and one active tag. The small size tag developed in this work operated with a coin type battery. To make the tag smaller, we used an internal PCB antenna and a chip antenna. We tested the performance of the tag. To reduce the manufacturing cost of our RF system, we used low price RF transceiver CC2510 chip-set. The CC2510 chip-set provided RSSI(Received Signal Strength Indicator) signal which could be used to determine the distances between an active tag and three active readers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1299-1308
• /
• 2007

In this paper, we propose the calibration method of monopulse slope to minimize the variation of angle estimate in frequency agile noncoherent monopulse system. We analyze the monopulse slope characteristics of antenna and RF receiver including the phase and gain imbalances of each receiving channel and present the calibration method to minimize the phase and gain imbalances of RF receiver channels including antenna. In addition, we present the calibration method using channel switching to minimize the gain imbalance of IF receiver channels. The measured average monopulse slope within the frequency bandwidth is -0.96, the maximum variation of angle estimate is similar to theoretical value, $0.15^{\circ}$ at ${\pm}2^{\circ}$ azimuth and $0.03^{\circ}$ at $0^{\circ}$ azimuth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.767-772
• /
• 2006

The receiver of this paper is Dual-band monopulse type for prototype of tracking radar. Localization of radar technology is an issue of SamsungThales and go into development. Dual-band radar in comparison with Single-band radar requires higher cost and power consumption but there are many advantages of dealing with jamming, detection range, image signal rejection, cloud-rain influence, clutter, resolution. The receiver is comprised of X-band RF head module, Ka-band RF head module and common IF module. Each signal of X-band and Ka-band is selected by the switch in If module. Phase shifter in IF module of local stage controls the phase of sum, azimuth, elevation channel. In the test result, gain is $40{\pm}3 dB$, isolation of transmitter/receiver is 39 dBc, dynamic range is 110 dB and noise figure of each channel is 4.5dB and 6.9dB.

• Journal of Navigation and Port Research
• /
• v.26 no.4
• /
• pp.419-426
• /
• 2002

The conventional RTK-GPS technique has many problems which are permission using RF wireless modem, influence of geographic obstacle using radio wave, frequency interference, finiteness of frequency resources. To solve these problems, in this paper, we designed the DGPS correction message transmission system as a method to substitute the RF wireless modem of RTK-DGPS receiver. Then the interface module was designed and implemented for linkage of GPS receiver and mobile phone. As a result worked differential surveying using receiving correction message using RS-232C and communication control, users of mobile station were worked differential surveying correction between mobile phones. Interface module system was received the same result of precision which was compared RF wireless modem system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.7
• /
• pp.657-663
• /
• 2009

A fully integrated single ended IR-UWB receiver is implemented using 0.18 ${\mu}m$ CMOS technology. The UWB receiver adopts the non-coherent architecture, which simplifies the RF architecture and reduces power consumption. The receiver consists of single-ended 2-stage LNAs, S2D, envelope detector, VGA, and comparator. The measured results show that sensitivity is -80.8 dBm at 1 Mbps and BER of $10^{-3}$. The receiver uses no external balun and the chip size is only $1.8{\times}0.9$ mm. The consumed current is very low with 13 mA at 1.8 V supply and the energy per bit performance is 23.4 nJ/bit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.1045-1050
• /
• 2008

In this paper presents a CMOS RF receiver for IR-UWB wireless communications is presented. The impulse radio based UWB receiver adopts the non-coherent demodulation that simplifies the receiver architecture and reduces power consumption. The IR-UWB receiver consists of LNA, envelop detector, VGA, and comparator and the receiver including envelope detector, VGA, and comparator is fabricated on a single chip using $0.18{\mu}m$ CMOS technology. The measured sensitivity of IR-UWB receiver is down to -70 dBm and the BER $10^{-3}$, respectively at data rate 1 Mbps. The current consumption of IR-UWB receiver except external LNA is 5 mA at 1.8 V.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.421-422
• /
• 2008

In this paper, CMOS RF front-end circuits for an L1/L5 dual-band global positioning system (GPS)/Galileo receiver are designed in $0.13\;{\mu}m$ CMOS technology. The RF front-end circuits are composed of an RF single-to-differential low noise amplifier, an RF polyphase filter, two down-conversion mixers, two transimpedance amplifiers, a IF polyphase filter, four de-coupling capacitors. The CMOS RF front-end circuits provide gains of 43 dB and 44 dB, noise figures of 4 dB and 3 dB and consume 3.6 mW and 4.8 mW from 1.2 V supply voltage for L1 and L5, respectively.

• Electronics and Telecommunications Trends
• /
• v.17 no.4 s.76
• /
• pp.101-112
• /
• 2002

RF 부품의 설계는 이용분야에 따라 그 설계법 및 제조공정이 달라지게 된다. 상업적인 이용분야에서는 대량생산 및 저가격화를 목적으로 하는데 반해, 통신위성 및 군사분야 등에서는 고신뢰도 및 고성능을 요구하게 된다. 그동안 국내의 RF 기술은 기본적으로 이동통신 및 위성방송수신기 등의 상업적인 분야에 치중되어 왔기 때문에 높은 신뢰도를 요구하는 위성중계기용 RF 설계기술의 기술수준은 선진국에 비해 매우 낮은 수준이다. 2005년도에는 국내에서 독자적으로 개발되고 있는 중계기를 탑재하는 통신위성이 발사될 예정이므로, 현 시점에서 높은 신뢰도를 갖는 위성중계기용 RF 부품의 설계법 및 제조공정 등을 살펴보는 것이 필요하리라 판단된다. 따라서 본 고에서는 높은 신뢰도를 갖는 위성중계기용 RF 부품의 설계 및 제조공정에 대하여 고찰한다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.26 no.4
• /
• pp.324-334
• /
• 2023

In this paper, the target simulator for RF signals was developed by using VST(Vector Signal Transceiver) and set by real-time signal processing SW programs. A function to process RF signals using FPGA(Field Programmable Gate Array) board was designed. The system functions capable of data processing, raw signals monitoring, target signals(simulated range, velocity) generating and RF environments data analyzing were implemented. And the characteristics of modulated signal were analyzed in RF environment. All function of programs for processing RF signal have options to store signal data and to manage the data. The validity of the signal simulation was confirmed through verification of simulated signal results.