• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.483-489
• /
• 2008

Masonry infill walls are frequently used as interior partitions and exterior walls in low- or middlerise RC buildings In the structural design and assessment of structural behaviors of buildings, the infill walls are usually treated as non-structural elements and they are ignored in analytical models. In this study, seismic behaviors of RC frame with/without masonry infill walls were investigated. To this end, the infill walls were modeled as equivalent diagonal struts. Based on analytical results, it has been shown that masonry infill walls can increase the global strength and stiffness of a structure. Accordingly, inter-story drift ratio will be decreased but seismic forces applied to the structure were increased than design seismic load because natural period of the structure was decreased. It is also seen from the analytical results that the inelastic deformation of RC frame with soft story is concentrated on the first story columns and thus, partial damage may have possibility of collapse of system.

• International Journal of Concrete Structures and Materials
• /
• 제9권4호
• /
• pp.439-451
• /
• 2015

This study analyzed the isolation effect for a 15-story reinforced concrete (RC) building with regard to changes in the beam-column stiffness ratio and the difference in the vibration period between the superstructure and an isolation layer in order to provide basic data that are needed to devise a framework for the design of isolated RC buildings. First, this analytical study proposes to design RC building frames by securing an isolation period that is at least 2.5 times longer than the natural vibration period of a superstructure and configuring a target isolation period that is 3.0 s or longer. To verify the proposed plan, shaking table tests were conducted on a scaled-down model of 15-story RC building installed with laminated rubber bearings. The experimental results indicate that the tested isolated structure, which complied with the proposed conditions, exhibited an almost constant response distribution, verifying that the behavior of the structure improved in terms of usability. The RC building's response to inter-story drift (which causes structural damage) was reduced by about one-third that of a non-isolated structure, thereby confirming that the safety of such a superstructure can be achieved through the building's improved seismic performance.

• 국제초고층학회논문집
• /
• 제3권4호
• /
• pp.285-296
• /
• 2014

The objective of optimization is to present a design process that minimizes the total material consumption while satisfying current codes and specifications. In the research an optimization formulation for RC shear wall structures is proposed. And based on conceptual design methodology, an optimization process is investigated. Then optimal design techniques and specific explanations are introduced for residential buildings with shear wall structure, especially for that with a rectangular layout. An example of 30-story building is presented to illustrate the effectiveness of the proposed optimal design process. Furthermore, the influence of aspect ratio on the concrete consumption and the steel consumption of the superstructure are analyzed for this typical RC shear wall structure; and their relations are obtained by regressive analysis. Finally, the optimal material consumption is suggested for the residential building with RC shear wall structure and with rectangular layout. The relation and the data suggested can be used for guiding the design of similar RC shear wall structures.

• Geomechanics and Engineering
• /
• 제23권3호
• /
• pp.275-287
• /
• 2020

Rectangular barrettes have been increasingly used as foundations for many infrastructure projects, but the vertical vibration of a barrette has been rarely addressed theoretically. This paper presents an analysis method of dynamic response for a rectangular barrette subjected to a time-harmonic vertical force with the aid of a modified Vlasov foundation model in multilayered viscoelastic soil. The barrette-soil system is modeled as a continuum, the vertical continuous displacement model for the barrette and soil is proposed. The governing equations of the barrette-soil system and the boundary conditions are obtained and the vertical shaft resistance of barrette is established by employing Hamilton's principle for the system and thin layer element, respectively. The physical meaning of the governing equations and shaft resistance is interpreted. The iterative solution algorithm flow is proposed to obtain the dynamic response of barrette. Good agreement of the analysis and comparison confirms the correctness of the present solution. A parametric study is further used to demonstrate the effects of cross section aspect ratio of barrettes, depth of soil column, and module ratio of substratum to the upper soil layers on the complex barrette-head stiffness and the resistance stiffness.

• 콘크리트학회지
• /
• 제6권5호
• /
• pp.183-192
• /
• 1994

지진하중을 받는 철근콘크리트 구조물의 안전성은 확정적 이론에 의한 평가보다 지진하중이 가지는 불확실성과 철근콘크리트의 이력특성을 고려하여 평가하는 것이 합리적이다. 확정적 이론에 의한 내진 구조물의 안전성 평가는 확률변수의 영향 등을 충분히 고려하기가 쉽지 않은데, 이러한 것들을 고려하기 위해서는 신뢰성이론 및 랜덤진동이론을 도입할 필요가 있으며 이에 의해 합리적으로 안전성을 검토하거나 확보할 수 있다. 본 연구에서는 철근콘크리트 뼈대구조물의 이력거동을 고려한 추계적 지진응답을 이용하여 지진손상정도와 위험성을 평가하고자 하였으며, 지진하중을 받는 뼈대구조물의 파괴확률을 계산하는 과정을 제시하였다.

• 한국강구조학회 논문집
• /
• 제22권5호
• /
• pp.455-463
• /
• 2010

본 연구는 철근콘크리트 구조와 강판 콘크리트 구조가 혼합되어 이질접합부가 있는 보형 구조물의 역학적 특성을 평가하기 위하여 수행하였다. 강판콘크리트 구조는 현재 국내와 일본, 미국 등에서 연구가 진행되고 있고, 대규모 산업설비에서 철근콘크리트 구조의 대안으로 실험연구가 수행되고 있다. 본 연구에서는 대규모 철근콘크리트 구조물에 강판 콘크리트 구조를 적용할 경우를 가정하여 보 형태의 구조물에 강판 콘크리트 구조와 철근 콘크리트 구조를 적용하여 이질접합부를 만들고, 면외하중을 파괴 시까지 가력하여 이질접합부를 가진 보형실험체의 휨 내력 및 구조특성을 평가하기 위하여 실험연구를 수행하였다.

• Structural Engineering and Mechanics
• /
• 제47권6호
• /
• pp.791-818
• /
• 2013

The seismic performance of reinforced concrete (RC) frame structures with irregularities leading to soft first floor is studied using capacity assessment procedures. The soft first story effect is investigated for the cases: (i) slab-column connections without beams at the first floor, (ii) tall first story height and (iii) pilotis type building (open ground story). The effects of the first floor irregularity on the RC frame structure performance stages at global and local level (limit states) are investigated. Assessment based on the Capacity Spectrum Method (ATC-40) and on the Coefficient Method (FEMA 356) is also examined. Results in terms of failure modes, capacity curves, interstory drifts, ductility requirements and infills behaviour are presented. From the results it can be deduced that the global capacity of the structures is decreased due to the considered first floor morphology irregularities in comparison to the capacities of the regular structure. An increase of the demands for interstory drift is observed at the first floor level due to the considered irregularities while the open ground floor structure (pilotis type) led to even higher values of interstory drift demands at the first story. In the cases of tall first story and slab-column connections without beams soft-story mechanisms have also been observed at the first floor. Rotational criteria (EC8-part3) showed that the structure with slab-column connections without beams exhibited the most critical response.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권6호
• /
• pp.201-211
• /
• 2011

우리나라는 삼면이 바다로 이루어져 있으며 많은 철근콘크리트 구조물이 위치해 있다. 만약 철근콘크리트 구조물이 염해의 노출이 장기화 된다면 철근의 부식으로 인하여 철근-콘크리트 부착성능이 감소될 뿐만 아니라, RC 구조물의 성능저하가 우려되고 있다. 따라서 본 연구에서는 부착성능이 상실된 RC 보-기둥 접합부에 대한 기초자료를 확보하기 위해 연구를 수행하였다. 철근-콘크리트 부착이 상실된 보-기둥 접합부를 제작하여 부착 및 비부착 특성 여부에 따라 반복 횡하중 실험 및 해석적 연구를 수행하여 접합부의 성능을 평가 및 고찰하였다.

• Computers and Concrete
• /
• 제27권4호
• /
• pp.385-393
• /
• 2021

Reinforcement corrosion is the main cause of the durability failure of reinforced concrete (RC) structure. In this paper, a three-dimensional (3D) numerical model of macro-cell corrosion is established to reveal the corrosion mechanisms of steel reinforcement in RC structure. Modified Direct Iteration Method (MDIM) is employed to solve the system of partial differential equations for reinforcement corrosion. Through the sensitivity analysis of electrochemical parameters, it is found that the average corrosion current density is more sensitive to the change of cathodic Tafel slope and anodic equilibrium potential, compared with the other electrochemical parameters. Furthermore, both the anode-to-cathode (A/C) ratio and the anodic length have significant influences on the average corrosion current density, especially when A/C ratio is less than 0.5 and anodic length is less than 35 mm. More importantly, it is demonstrated that the corrosion rate of semi-circumferential corrosion is much larger than that of circumferential corrosion for the same A/C ratio value. The simulation results can give a unique insight into understanding the detailed electrochemical corrosion processes of steel reinforcement in RC structure for application in service life prediction of RC structures in actual civil engineer.

• Structural Engineering and Mechanics
• /
• 제85권5호
• /
• pp.655-664
• /
• 2023

Reinforced concrete (RC) shear wall structures are one of the most widely used structural systems to resist seismic loading all around the world. Although there have been several efforts to provide conceptually simple procedures to reasonably assess the seismic demands of structures over recent decades, it seems that lesser effort has been put on a number of structural forms such as RC shear wall structures. Therefore, this study aims to represent a simple linear response spectrum-based method which can acceptably predict the nonlinear displacements of a non-ductile RC shear wall structure subjected to an individual ground motion record. An effective period and an equivalent damping ratio are introduced as the dynamic characteristics of an equivalent linear SDOF system relevant to the main structure. By applying the fundamental mode participation factor of the original MDOF structure to the linear spectral response of the equivalent SDOF system, an acceptable estimation of the nonlinear displacement response is obtained. Subsequently, the accuracy of the proposed method is evaluated by comparison with another approximate method which is based on linear response spectrum. Results show that the proposed method has better estimations for maximum nonlinear responses and is more utilizable and applicable than the other one.