• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.446-449
• /
• 2006

Several experimental investigations have been carried out to study the behavior of reinforced concrete columns with short lap splices. However, very few analytical models have been developed for the analysis of such columns subjected to earthquakes. As nonlinear analysis procedures become more common in practice (such as those outlined in the Guidelines for Seismic Rehabilitation of Buildings published by the Federal Emergency Management Agency in the United States), the need for an accurate and reliable representation of the nonlinear response of strength degrading systems becomes more important. In this study, an analytical model for estimating the complete response of reinforced concrete columns with short lap splices is presented. The model is based on local bond stress-slip relationships and is validated against independent experimental data from cyclic loading tests on reinforced concrete columns with typical construction details of the 1960s. In this paper a simple equation for calculating the bar stress at splice failure is presented. Use of the proposed equation resulted in excellent agreement between the measured and calculated strength at splice failure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.173-177
• /
• 1992

The Helicopter has a lot of flight modes. The most characteristic flight mode is Hovering. It enables the helicopter to be used in many situations. However, a helicopter has nonlinear dynamics so its mathematical modeling is very difficult. Hence it is not easy to control helicopter in hover. In this paper, RC model helicopter is selected as a plant. To stabilize the behavior of RC model helicopter, Fuzzy alogrithm is used as a controller and one camera is used as a sensor. To get proper Information from camera Image, three characteristic points are attatched to the helicopter and a position recognition algorithm is developed. Experiments are performed to stabilize 3 rotational motions synchronousely with fuzzy control algorithm. As a result, Fuzzy control represents better performances than the conventional PID control.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2012년도 춘계학술발표회 초록집
• /
• pp.420-423
• /
• 2012

원자력 발전소는 화재 발생 시 대규모 피해를 야기하는 특수한 시설물로서 일반 건축물에 비하여 매우 엄격한 화재 안전 기준을 적용하고 있으며 일반 건축물과 차별화된 화재안전 설계 조건을 요구한다. 본 연구에서는 원자력 발전소의 화재안전성을 평가하기 위한 기초연구로써 원자력 발전소 내 주 제어실(이하 MCR)에 대해 화재시나리오 및 환기조건에 따른 화재해석모델의 계산결과를 비교분석하여 각 해석모델의 특성을 파악하고자 한다. MCR 내 화재안전성을 평가하기 위해 Field Model인 FDS 와 Zone Model인 CFAST를 이용하였으며 NUREG/RC-6850, NUREG/RC-1894에 기초하여 화재시뮬레이션을 수행하였다. 해석결과로써 연기농도, 가시거리, 연층높이 등의 데이터를 분석하여 MCR내의 거주가능 시간을 평가하였으며 이를 통해 원자력 시설물의 안전성 확보를 위한 정량적인 자료를 제공하고자 한다.

• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.83-93
• /
• 1999

This paper presents tension stiffening effect of Reinforced concrete members obtained from experimental results on direct tension and bending. From the direct tension test program, crack patterns were investigated with tension softening behaviors of concrete. Tension stiffening effects and losses of strain energy were, also, analyzed from the load-deflection curve with the main experimental variables such as concrete strength, yielding stress and reinforcement ratio of rebar. Tension stiffening effect of RC members increase linearly until the first crack initiate, decrease inversely with number of cracks, and then decrease rapidly when splitting cracks are happened. The tension stiffening effect is shown to be more important at the member of lower reinforcement than that of higher. Therefore, it necessitates to consider the tension stiffening effects at a nonlinear analysis. From the above analysis, a tension stiffening model of concrete is proposed and verified by applying it to bending members. From the numerical analysis by finite element approach, it is shown that the proposed model evaluates a little higher in analyzing at nonlinear region of high strength concrete, but, perform satisfactorily in general.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.367-370
• /
• 2005

This study is to propose a truss model which is able to reasonably predict the shear strength of reinforced concrete (RC) members with high-strength materials. The shear strengths of 107 RC test beams with high-strength steel bars reported in the technical literatures were compared to those obtained from proposed model, TATM, and existing truss models. The shear strength of reinforced concrete beams obtained from test was better predicted by TATM than other truss models. Also, the theoretical results by TATM were almost constant regardless of yield strengths and steel ratios of tension and shear reinforcements.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.195-198
• /
• 2005

To investigate the strengthening efficiency of the Near Surface Mounted Reinforcement (NSMR) technique analytically, a structural model for the finite element method (FEM) able to simulate accurately the experimental results was determined. Applying the finite element model, parametric analysis was performed considering the groove depth and spacing of CFRP laminates. Analytical study on the groove depth revealed the existence of a critical depth beyond which the increase of the ultimate load becomes imperceptible. Analytical results regard to the spacing of the CFRP laminates showed that comparatively smooth fluctuations of the ultimate load were produced by the variation of the spacing and the presence of an optimal spacing range for which relatively better strengthening efficiency can be obtained. Particularly, a spacing preventing the interference between adjacent CFRP laminates and the influence of the concrete cover at the edges as well as allowing the CFRP laminatesto behave independently was derived.

• Structural Engineering and Mechanics
• /
• 제5권6호
• /
• pp.743-754
• /
• 1997

A three-dimensional constitutive modeling for reinforced concrete is presented for finite element nonlinear analysis of reinforced concrete. The targets of interest to the authors are columns confined by lateral steel hoops, RC thin shells subjected to combined in-plane and out-of-plane actions and massive structures of three-dimensional (3D) extent in shear. The elasto-plastic and continuum fracture law is applied to pre-cracked solid concrete. For post cracking formulation, fixed multi-directional smeared crack model is adopted for RC domains of 3D geometry subjected to monotonic and reversed cyclic actions. The authors propose a new scheme of decomposing stress strain fields into sub-planes on which 2D constitutive laws can be applied. The proposed model for 3D reinforced concrete is experimentally verified in both member and structural levels under cyclic actions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.413-416
• /
• 2004

This paper describes a proposal for crack width and deflection in RC flexural members. Because the serviceability provisions of the current codes are mainly based on only empirical relationships developed from test result and effective moment of inertia, crack width and deflections are contrary to the actual values. Based on nonlinear bond characteristics, tension stiffening effect, arch action and effective concrete tensile area. Then an equation is developed for predicting crack width and deflection in flexural members. The predicted results shows that as proposed model employed, crack width and deflections are different from estimated by the current KCI, MC 90 and EC 2 provisons, and the values predicted are in good agreement with experimentally measured values.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2006년도 학술발표회 논문집
• /
• pp.168-179
• /
• 2006

This paper summarizes full-scale test results on CFT column-to-flat plate connections subjected to gravity loading. CFT construction has gained wide acceptance in a relatively short time in domestic building construction practice due to its various structural and construction advantages. However, efficient details for CFT column to flat plate connections have not been proposed yet. Based on the strategies that maximize economical field construction, several connecting schemes were proposed and tested. Test results showed that the proposed connections can exhibit punching shear strength and connection stiffness exceeding those of R/C flat plate counterparts. A semi-analytical procedure is presented to model the behavior of CFT column-to-flat plate connections. The five parameters to model elastic to post-punching catenary action range are calibrated based on the limited test data of this study. The application of the proposed modeling procedure to progressive collapse prevention design is also illustrated.

• Advances in concrete construction
• /
• 제14권2호
• /
• pp.131-137
• /
• 2022

Based on the design of reinforced concrete columns in Chinese design codes, the failure function of reinforced concrete (RC) columns cannot be expressed as a linear function. This makes it difficult to reveal the level of reliability control in Chinese design code. Therefore, the failure function of dimensionless form is established in this paper, and the typical components (Industrial plant columns) are selected for analysis. At last, numerical simulation proves that the proposed model can be used to analysis reliability of columns. The results based on this model indicate that there is a strong difference in the reliability of RC columns designed with different design parameters, and the reliability would be lower when the eccentricity produced by crane load is smaller.