• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.5
• /
• pp.401-407
• /
• 1984

In the previous paper, part I, the principal stresses were investigated on the normal tools and the workpieces whose materials were the same epoxy resin. In this paper, are measured and compared the stresses on the normal tools and restricted tools which have three various rake angles. Each restricted tool above has the same restricted angle. The workpieces used in this experiment are made of high quality lead. The photoelastic measuring device is attached to the saddle of the lathe and carried at the same speed as the cutting tool is feeded. The results obtained are summarized as follows; The shear stresses on the tip of the restricted tools of the rake angle .alpha.=12.deg. and .alpha.=0.deg. are less than those of normal tools. But, for the rake angle .alpha.=-12.deg., the former is greater than the latter. The result of photoelastic method shows that in the range of rapid decreasing of normal stress on the tool edge, the shear is maintaining a certain value.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.365-370
• /
• 1999

SKD11 is one of the most difficult workpiece for machining, so it is necessary to evaluate the machining characteristics of SKD11. The workpiece was made to be the pipe form and heat-treated to HRC45. In this paper, the orthogonal cutting experiment of this material was carried out with TiAlN coated WC cutting tool of 4 kinds of rake angle. After cutting experiment, cutting characteristics of SKD11 were investigated according to variation of cutting speed, feedrate and rake angle.

• Journal of information and communication convergence engineering
• /
• v.7 no.3
• /
• pp.286-291
• /
• 2009

In this paper, the performance of ultra-wideband (UWB) single input multiple output (SIMO) systems to achieve high data rate communications is studied in dense multipath environments. The effects of spatial and temporal diversities on the performance of multi-user time-hopping UWB systems using binary pulse position modulation (2PPM) are analyzed. The reduced-complexity Rake receivers based on the selective combining (called SRake) and partial combining (called PRake) are considered. The theoretical and simulation results show that the BER performance of the UWB system can be enhanced as the number of array elements and/or Rake fingers increases. Moreover, we observe that SRake is more effective for the IR-UWB systems to achieve a good BER performance, as compared with PRake.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.14-21
• /
• 2010

In this study, presintered low purity alumina ceramics were machined with various tools to clarify the effects of the tool material, cutting condition and tool geometry on machinability. The main conclusions obtained were as follows. (a)The wear of tungsten carbide tool becomes smaller with the increase of the feed and clearance angle, and with the decrease of rake angle, especially exhibiting considerably smaller wear with both the decrease of rake angle and the increase of clearance angle. (b) So far as turning the ceramic presintered at low temperature, the diamond tool shows the best performance with higher feed. (c) The effect on the tool wear of the feed, clearance angle and rake angle becomes smaller in turning the ceramic presintered at higher temperature. (d) The tool wear is not severely affected by the depth of cut.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.471-478
• /
• 2000

Endmill is one of the most important cutting tool, not only for machining of mold and die, but also for manufacturing of car industrial. Futhermore with spindle speeds on the increase and machined-surface quality aspiring to higher levels. The purpose of this study is an analysis of endmill's rake angle for appropriate tools design and making for the high speed machining. In this study, Experimental works are also executed to measure shape of endmills, cutting force, on different shape of endmills. Finally, To get concept of endmill design, Tool life was experimented on various design of tool from this study.

• Journal of the Korean Society for Precision Engineering
• /
• v.1 no.1
• /
• pp.50-58
• /
• 1984

In the present paper are calculated and compared the stresses on the normal tools and the restricted tools which have three various rake angles by Least Square Method. The results obtained are summerized as follows. The tool displacement at rake angle .alpha. = 12 .deg. and .alpha. = 0 .deg. is positive value in the principal cutting direction and negative value in the feed direction. At rake angle .alpha. = -12 .deg. the displacement is negative value in both of directions. The principal stress of the restricted and normal tool is maximum at the tip of the tool, the shear stress is maximum after a certain distance from the tip. The result of FEM and P.E method shows that in the range of rapid decreasing of normal stress of the tool edge, the shear stress is maintaining a certain value. This is due to the friction characteristic of the chip.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.47-57
• /
• 1987

The objective of this study is to establish the comprehensive analytical relationship between acoustic emission and fundamental parameters of the orthogonal cutting process. The sources of acoustic emission in the orthogonal metal cutting process was identified as deformation in the shear zone and sliding friction at the chip-tool interface. The validity of this relationship is evaluated by a series of tests varing cutting speed and rake angle for A16063 tube. Strong dependence of the RMS voltage of acoustic emission on cutting speed and rake angle was observed. It was also found that the percentage contribution of AE energy at each zone for the total AE activity is constant in accordance with the change of cutting speed. The relationship between the RMS of acoustic emission and the fundamental cutting parameters was modified in order to be utilized independent of rake angle.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2017.11a
• /
• pp.395-398
• /
• 2017

We propose a web crawler system with keyword extraction function in this paper. Researches on the keyword extraction in existing text mining are mostly based on databases which have already been grabbed by documents or corpora, but the purpose of this paper is to establish a real-time keyword extraction system which can extract the keywords of the corresponding text and store them into the database together while grasping the text of the web page. In this paper, we design and implement a crawler combining RAKE keyword extraction algorithm. It can extract keywords from the corresponding content while grasping the content of web page. As a result, the performance of the RAKE algorithm is improved by increasing the weight of the important features (such as the noun appearing in the title). The experimental results show that this method is superior to the existing method and it can extract keywords satisfactorily.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2621-2624
• /
• 2008

The study on the measurement method of the aerodynamic performance of a turbo compressor was conducted. It is well known that the performance and the efficiency of the compressor can be calculated from the temperature and pressure distribution in each stage of the compressor. In the past Pitot tubes and thermocouples were used to measure pressure and temperature respectively, and recently pressure and temperature rake is used in order to decrease the measuring time and the number of measurement. The miniature total pressure rake which is available in the compressor with a small axial gap is designed and is under development.

• Journal of information and communication convergence engineering
• /
• v.10 no.3
• /
• pp.215-219
• /
• 2012

This paper applies transmit antenna selection algorithms to spatial-temporal combining-based spatial multiplexing (SM) ultra-wideband (UWB) systems. The employed criterion is based on the largest minimum output signal-to-noise ratio of the multiplexed streams. It is shown via simulations that the bit error rate (BER) performance of the SM UWB systems based on the two-dimensional Rake receiver is significantly improved by antenna diversity through transmit antenna selection on a log-normal multipath fading channel. When the transmit antenna diversity through antenna selection is exploited in the SM UWB systems, the BER performance of the spatial-temporal combining-based zero-forcing (ZF) receiver is also compared with that of the ZF detector followed by the Rake receiver.