• Journal of the Korean Electrochemical Society
• /
• v.3 no.4
• /
• pp.204-210
• /
• 2000

The control of dissolved aluminum concentration in the hot dip zinc galvanizing bath is greatly important in producing galvannealed steel sheets. The purpose of present study is to provide basic data for measurement of the aluminum concentration in site in hot dip zinc bath at the temperature of $460^{\circ}C\~500^{\circ}C$ using $CaF_2$ solid electrolyte sensor with three kinds of reference electrode. Good workability and stability of the sensor were confirmed with the $Bi+BiF_3$ reference electrode from the emf measurement. In order to measure the aluminum concentration in Zn-Al bath, the galvanic cell of fluorine ion was constructed with $CaF_2$ solid electrolyte as follows; $$(-)W|Zn-Al,\;AlF_3|CaF_2|Bi,BiF_3|W(+)$$. The emf measurement was made at the temperature of $460\pm10^{\circ}C$ in the Zn-Al bath. The following correlationship between aluminum concentration and emf was obtained by the least square regression analysis; $$E/mV=56.795log[\%Al]+1881.7\;R=0.9704$$,$$0.026wt\%{\leq}[\%Al]{\leq}0.984wt\%$$

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.289-299
• /
• 2001

본 연구는 균질 및 2개층 비균질지반에서 사질토지반 상에 놓인 정방형 기초의 극한지지력과 침하에 대하여 고찰하였다. 본 연구는 얕은기초의 거동에 대한 정방형 기초의 크기, 지반 상대밀도, 기초 폭에 대한 상부층의 두께 비(H/B), 상부층 아래 경계면의 경사($\theta$) 그리고 지반강성비의 영향을 규명하기 위하여 모형실험을 수행하였다. 동일 상대밀도에서 지지력 계수($N_{{\gamma}}$)는 일정하지 않으며 기초 폭에 직접적으로 관련되며 지지력계수는 기초 폭이 증가함에 따라 감소하였다. 기초크기의 영향과 구속압력의 영향을 고려하는 Ueno 방법에 의한 극한지지력의 예측값은 고전적인 지지력 산정식보다 더 잘 일치하며 그 값은 실험값의 65% 이상으로 나타났다. $\theta$=$0^{\circ}$인 2개층 지반의 결과에 근거하여, 극한지지력에 대한 하부층 지반의 영향을 무시할 수 있는 한계 상부층 두께는 기초 폭의 2배로 결정되었다. 그러나, 73%의 상부층 상대밀도인 경우는 침하비($\delta$B) 0.05 이하에서만 이 결과가 유효하였다. 경계면이 경사진 2개층 지반의 결과에 근거하여, 상부층의 상대밀도가 느슨할수록 그리고 상부층의 두께가 클수록 극한지지력에 대한 경계면 경사의 영향은 크지 않는 것으로 나타났다. 경계면의 경사가 증가함에 따른 극한침하량의 변화는 경계면이 수평인 경우($\theta$=$0^{\circ}$)를 기준으로 0.82~1.2(상부층 $D_{r}$=73%인 경우) 그리고 0.9~1.07(상부층 $D_{r}$=50%인 경우) 정도로 나타났다.Markup Language 문서로부터 무선 마크업 언어 문서로 자동 변환된 텍스트를 인코딩하는 경우와 같이 특정한 응용 분야에서는 일반 문자열에 대한 확장 인코딩 기법을 적용할 필요가 있을 수 있다.mical etch-stop method for the etching of Si in TMAH:IPA;pyrazine solutions provides a powerful and versatile alternative process for fabricating high-yield Si micro-membranes. the RSC circle, but also to the logistics system in the SLC circle. Thus, the RSLC model can maximize combat synergy effects by integrating the RSC and the SLC. With a similar logic, this paper develops "A Revised System of Systems with Logistics (RSSL)" which combines "A New system of Systems" and logistics. These tow models proposed here help explain several issues such as logistics environment in future warfare, MOE(Measure of Effectiveness( on logistics performance, and COA(Course of Actions) for decreasing mass and increasing velocity. In particular, velocity in logistics is emphasized.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.6
• /
• pp.445-452
• /
• 2015

Software reliability in the software development process is an important issue. Software process improvement helps in finishing with reliable software product. Infinite failure NHPP software reliability models presented in the literature exhibit either constant, monotonic increasing or monotonic decreasing failure occurrence rates per fault. In this paper, proposes the reliability model with log and power intensity function (log linear, log power and exponential power), which made out efficiency application for software reliability. Algorithm to estimate the parameters used to maximum likelihood estimator and bisection method, model selection based on mean square error (MSE) and coefficient of determination($R^2$), for the sake of efficient model, was employed. Analysis of failure, using real data set for the sake of proposing log and power intensity function, was employed. This analysis of failure data compared with log and power intensity function. In order to insurance for the reliability of data, Laplace trend test was employed. In this study, the log type model is also efficient in terms of reliability because it (the coefficient of determination is 70% or more) in the field of the conventional model can be used as an alternative could be confirmed. From this paper, software developers have to consider the growth model by prior knowledge of the software to identify failure modes which can be able to help.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.99-106
• /
• 1998

The performance of the turbofan engine, a medium scale civil aircraft which has been developing in Rep. of Korea, was analyzed and the control scheme for optimization the performance was studied. The dynamic and real-time linear simulation was performed in the previous study The result was that the fuel scedule of the step increase overshoot the limit temperature(3105 $^{\cire}R$) of the high pressure turbine and got small surge margine of the high pressure compressor. Therefore a control scheme such as the LQR(Linear Quadratic Regulator) was applied to optimizing the performance in this studies. The linear model was expected for designing controller and the real time linear model was developed to be closed to nonlinear simulation results. The system matrices were derived from sampling operating points in the scheduled range and then the least square method was applied to the interpolation between these sampling points, where each element of matrices was a function of the rotor speed. The control variables were the fuel flow and the low pressure compressor bleed air. The controlled linear model eliminated the inlet temperature overshoot of the high pressure turbine and obtained maximum surge margins within 0.55. The SFC was stabilized in the range of 0.355 to 0.43.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.22 no.4
• /
• pp.37-45
• /
• 2016

Purpose: The purpose of this paper is to analyze a sample of single corridor, pod type and composite type of ICUs in terms of patient visibility, spatial configurations and nurse walking distance focused on Korean cases. Methods: The measures of static visibility were used to quantify the patient visibility (upper third part of the patient bed) from the nurse station. The measure of space programme and area distribution (patient zone percentage, staff zone percentage, circulation zone percentage, corridor length per bed, distance from nurse station (NS) to patient bed and departmental gross square meter (DGSM) per patient bed) were calculated by using AutoCAD and MS Excel programs. In the second step of analysis the values of space distribution were compared among the three type of ICUs as well as the nurse walking distance, DGSM per bed and gross factor. in the third step of analysis regression analysis was conducted for the possible correlation between visibility and space programme and area distribution factors as well as nurse walking distance factors. Results: (1) It was found that on average composite type unit offer highest value of patient visibility followed by pod type, while single corridor type unit offers the minimum value of patient visibility among the three plan typologies. (2) Average patient visibility and DGSM per bed shows a strong positive correlation ($r^2=0.75$) and p=0.026. (3) Average patient visibility and average distance from NS has a strong negative correlation ($r^2=0.78$), and P=0.02. (4) On average composite type unit offer the minimum walking distance from NS (7.22 meter) followed by pod type unit (8.35 meter) and single corridor (9.76 meter). (5) Maximum distance from NS was noted in single corridor (18.19 meter) followed by pod type unit (15.14 meter) and Composite type unit (11.1 meter). Implications: This study may contribute to the visibility analysis of existing and future ICU design in Korea to achieve maximum patient visibility and reduced nurse walking distance.

• Journal of the Korean Society of Safety
• /
• v.31 no.3
• /
• pp.8-15
• /
• 2016

The purpose of this study is to design a model with the structural stability so as not to lose the operational function due to structural plastic or fail of a sliding blast door by blast pressure to this aim, a numerical simulation was performed using full-size experiments and M&S (Modeling & Simulation) of the sliding blast door. The sliding blast door ($W3,000{\times}H2,500mm$) under the blast load is in the form of a sliding type 2-way metal grill, which was applied by a design blast pressure (reflected pressure $P_r$) of 17 bar. According to the experimental results of a real sliding blast door under blast load, the blast pressure reached the sliding blast door approximately 4.3 ms after the explosion and lasted about 4.0 ms thereafter. The maximum blast pressure($P_r$) was 347.7 psi (2,397.3 kPa), it is similar to the UFC 3-340-02 of Parameter(91 %). In addition, operation inspection that was conducted for the sliding blast door after real test showed a problem of losing the door opening function, which was because of the fail of the Reversal Bolt that was installed to prevent the shock due to rebound of the blast door from the blast pressure. According to the reproduction of the experiment through M&S by applying the blast pressure measurement value of the full-size experiments, the sliding blast door showed a similar result to the full-size experiment in that the reversal bolt part failed to lose the function. In addition, as the pressure is concentrated on the failed reversal bolt, the Principal Tensile Failure Stress was exceeded in only 1.25 ms after the explosion, and the reversal bolt completely failed after 5.4 ms. Based on the result of the failed reversal bolt through the full-size experiment and M&S, the shape and size of the bolts were changed to re-design the M&S and re-analyze the sliding blast door. According to the M&S re-analysis result when the reversal bolt was designed in a square of 25 mm ($625mm^2$), the maximum pressure that the reversal bolt receives showed 81% of the principal tensile failure stress of the material, in plastic stage before fail.

• Journal of Pharmaceutical Investigation
• /
• v.23 no.1
• /
• pp.41-49
• /
• 1993

The bioequivalence of two omeprazole enteric-coated products was evaluated in 16 normal male volunteers (age 26-32 yr, body weight 57-75 kg) following single oral administration. Test product was enteric-coated KD-182 tablet (Chong Kun Dang Corp., Korea) and reference product was $Rosec^{\circledR}$ capsule containing enteric-coated pellets of omeprazole (Yuhan Corp., Korea). Both products contain 20 mg of omeprazole. One tablet or capsule of the test or the reference product was administered to the volunteers, respectively, by randomized two period cross-over study ($2\;{\times}\;2$ Latin square method). Average drug concetrations at each sampling time and pharmacokinetic parameters calculated were not significantly different between two products(p>0.05); the area under the concentrationtime curve to last sampling time (8 hr) $(AUC_{0-8hr})$ $(1946.5{\pm}675.3\;vs\;2018.3{\pm}761.6\;ng{\cdot}hr/ml)$, AUC from time zero to infinite $(AUC_{o-\infty})$ $(2288.6{\pm}1212.8\;vs\;2264.9{\pm}1001.3\;ng{\cdot}hr/ml)$, maximum plasma concentration $(C_{max})$ $(772.5{\pm}283.3\;vs\;925.8{\pm}187.7\;ng/ml)$, time to maximum plasma concentration $(T_{max})$ $(2.38{\pm}1.06\;vs\;2.34{\pm}1.09\;hr)$, apparent elimination rate constant $(k_{\ell})$ $(0.5339{\pm}0.2687\;vs\;0.5769 {\pm}0.2184\;hr^{-I})$, apparent absorption rate constant $(k_a)$ $(1.1536{\pm}0.5278\;vs\;0.9739{\pm}0.9507 hr^{-1})$ and mean residence time (MRT) $(3.13{\pm}0.73\;vs \;3.41{\pm}1.04\;hr)$. The differences of mean $(AUC_{0-8hr})$, $C_{max}$, $T_{max}$ and MRT between the two products (3.69, 19.83, 1.32 and 8.99%, respectively) were less than 20%. The power $(1-{\beta})$ and treatment difference $(\triangle)$ for $AUC_{o-8hr}$ $C_{max}$ and MRT were more than 0.8 and less than 0.2, respectively. Although the power for $T_{max}$ was under 0.8, $T_{max}$ of the two products was not significantly different each other(p>0.05). These results suggest that the bioavailability of KD-182 tablet is not significantly different from that of $Rosec^{\circledR}$ capsule. Therefore, two products are bioequivalent based on the current results.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.6
• /
• pp.699-705
• /
• 1997

This experiment was conducted to find out an optimum direct seeding date for rice in the southern alpine area of Korea as direct seeding method being considered as the most labor-saving method. A cultivar which was sprouted, Keumobyeo, was sown on the surface of flooded paddy from April 25 to May 15 with 5-day interval. The growth characters such plant height, tiller numbers, yield and its components as well as air temperatures were observed. Earlier sowing showed longer plant height and greater tillers than later sowing. Accumulated temperatures in the different growth stages varied from 1,010 to 1,052$^{\circ}C$ during the period from seeding date to maximum tillering stage, and from 1,785 to 1,846$^{\circ}C$ during the period from seeding to heading dates. The growth of rice sown up to May 5 showed comparatively good when compared to that of machine-transplanted rice, even though the grain yield was not competitive to that of machine-transplanted rice. Highly negative correlation coefficients were found between accumulated temperature during the period of first 30 days after seeding dates and the number of panicles, the number of spikelets per square meter, and grain yield. Regression equation between direct seeding date(X) and yield(Y;MT /ha) was $\hat{Y}$ =3.80990＋0.06207X-0.00174 $X^2$($R^2$=0.704), from which optimum seeding date for direct seeding method in alpine area was estimated to be on April 25 to May 1.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.103-103
• /
• 2012

본 연구에서는 시험포장($1276.6m^2$)에서의 지표피복 BMPs (Best Management Practices) 시나리오를 적용하여 얻은 평균 유출저감율을 HSPF 모델에 적용하여 유역차원에서의 비점원오염 저감효과를 평가하고자 한다. 본 연구에서는 별미천 유역($1.21km^2$)을 대상으로 모형의 적용을 위한 입력자료로 기상자료와 지형자료를 구축하였으며 기상자료로 수원, 양평, 이천 기상관측소 자료를 구축하였으며, 지형자료로 격자크기 2m의 DEM (Digital Elevation Model)과 토지이용도는 2006년 5월 1일 QuickBird 영상을 제공받아 기존 환경부, 건교부, USGS의 토지피복분류체계 및 현장조사를 통하여 QuickBird 영상으로부터 추출 가능한 정밀농업정보에 대한 항목을 결정하였으며, 정사보정된 QuickBird 영상을 스크린 디지타이징 기법(On-Screen Digitizing Method)을 이용하여 총 21개 토지이용항목의 정밀토지이용도를 구축하였다. 실제모니터링으로 측정된 자료를 바탕으로 수위-유량곡선 산정 및 오염부하곡선을 선정, 2011년 6월 8일부터 10월 31일 분석기간으로 HSPF 모델링을 실시하였으며 모의결과 월별 통계에 따른 적용성 분석으로 RMSE (Root Mean Square Error) 는 1.15 ~ 1.76(mm/day), $R^2$는 0.62 ~ 0.78, Nash-Sutcliffe model efficiency (NSE)는 0.62 ~ 0.76로 모의치는 실측치와 유의성이 있는 것으로 분석되었다. 또한, Sediment, T-N, T-P의 $R^2$는 각각 0.72, 0.62, 0.63으로 상관성을 보이는 것으로 분석되었다. 시험포장으로부터 얻어진 event별 볏짚을 이용한 지표피복시나리오적용 후 밭에서의 평균 유출 약 10 % 유출율 감소 조건과 실제 평균 비점원오염 저감효과 89.7 % ~ 99.4 %의 결과로부터 지표피복효과의 침투효과를 HSPF 모델로 적용하기 위해 침투량(INFILT)를 조절하여 평균유출 약 10 %가 감소되는 16.0 mm/hr 값을 선정하였다. 그 결과, Sediment. T-N, T-P의 평균 저감율은 각각 87.2 %, 28.5 %, 85.1 %로 나타났으며 이는 시험포장에서의 실제 평균 비점오염 저감효과 89.7 % ~ 99.4 %에 근접함을 알 수 있었다. 이 결과로부터 침투량 조절에 따른 지표피복(침투짚단)효과는 Sediment, T-P에서 저감효율이 80 % 이상으로 높았지만 T-N은 약 30 %로 낮은 저감율을 보임으로써 저감효과가 크지 않음을 나타냈다.

• Journal of Korea Water Resources Association
• /
• v.51 no.10
• /
• pp.839-852
• /
• 2018

The purpose of this study is to predict monthly agricultural reservoir storage by developing weather data-based Multiple Linear Regression Model (MLRM) with precipitation, maximum temperature, minimum temperature, average temperature, and average wind speed. Using Naïve-Bayes classification, total 1,559 nationwide reservoirs were classified into 30 clusters based on geomorphological specification (effective storage volume, irrigation area, watershed area, latitude, longitude and frequency of drought). For each cluster, the monthly MLRM was derived using 13 years (2002~2014) meteorological data by KMA (Korea Meteorological Administration) and reservoir storage rate data by KRC (Korea Rural Community). The MLRM for reservoir storage rate showed the determination coefficient ($R^2$) of 0.76, Nash-Sutcliffe efficiency (NSE) of 0.73, and root mean square error (RMSE) of 8.33% respectively. The MLRM was evaluated for 2 years (2015~2016) using 3 months weather forecast data of GloSea5 (GS5) by KMA. The Reservoir Drought Index (RDI) that was represented by present and normal year reservoir storage rate showed that the ROC (Receiver Operating Characteristics) average hit rate was 0.80 using observed data and 0.73 using GS5 data in the MLRM. Using the results of this study, future reservoir storage rates can be predicted and used as decision-making data on stable future agricultural water supply.