• Structural Engineering and Mechanics
• /
• 제16권3호
• /
• pp.361-369
• /
• 2003

In this paper, the structural behavior of R/C cylindrical panel is analyzed by experimental results. To avoid the geometric imperfection, R/C shell specimens are made by use of a stiff steel mold. From experimental results, the load carrying behavior of R/C cylindrical panel is presented under an external lateral pressure. Even if R/C shell does not posses geometric imperfections, the inaccuracy of the reinforcement position strongly affects to the ultimate strength and the failure patterns of such shells. To explain these effects, FEM nonlinear analyses are done under the same conditions as those of experiments. The behavior of R/C cylindrical shells are well simulated under the consideration of both the geometric imperfection and several inaccuracies.

• Computers and Concrete
• /
• 제8권1호
• /
• pp.97-110
• /
• 2011

In this paper, FEM procedure is applied to the static and dynamic analyses of R/C structures. Simple R/C shell structure is solved by using FEM procedures and the experimental evaluations are performed to represent the applicability of FEM procedure to R/C structures. Also, R/C columns are analyzed numerically and experimentally. On the basis of these results, FEM procedures are applied to the R/C cooling tower structures assembled by huge R/C shell structure and a lot of discrete R/C columns. In this analysis, the parallel computing procedures are introduced into these analyses to reduce the computational effort. The dynamic performances of R/C cooling tower are also solved by the application of parallel computations as well. From the numerical analyses, the conventional FEM procedures combined with computational technologies enables us to design the huge R/C structures statically and dynamically.

• 센서학회지
• /
• 제28권4호
• /
• pp.225-230
• /
• 2019

$Au@TiO_2$ core-shell decorated rGO nanocomposite (NC) was prepared using a simple solvothermal method followed by heat treatment for gas sensor application. The crystal structure and morphology of the composites were characterized by X-ray powder diffraction and transmission electron microscopy, respectively. The $NO_2$ sensing response of the $Au@TiO_2/rGO$ NC was tested at operating temperatures from $250^{\circ}C$ to $500^{\circ}C$, and was compared with those of the bare rGO and $Au@TiO_2$ core-shell NPs. The $Au@TiO_2/rGO$ NC-based sensor showed a far higher response than the rGO or $Au@TiO_2$ core-shell based sensors, with the maximum response detected when the operating temperature was $400^{\circ}C$. This improved response was due to the high rGO gas absorption capability for $NO_2$ gas and the catalytic effect of $Au@TiO_2$ core-shell NPs in oxidizing $NO_2$ to $NO_3$.

• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1535-1548
• /
• 2004

Condensation heat transfer experiments were conducted with the oblong shell and plate heat exchanger without oil in a refrigerant loop using R-l34a, R-407C and R-410A. An experimental refrigerant loop has been developed to measure the condensation heat transfer coefficient h$_{r}$ and frictional pressure drop $\Delta$p$_{f}$ of the various refrigerants in a vertical oblong shell and plate heat exchanger. The effects of the refrigerant mass flux(40∼80kg/$m^2$s), average heat flux(4∼8kW/$m^2$), refrigerant saturation temperature(30∼4$0^{\circ}C$) and vapor quality of refrigerants on the measured data were explored in detail. Similar to the case of a plate heat exchanger, even at a very low Reynolds number, the flow in the oblong shell and plate heat exchanger remains turbulent. A comparison of the performance of the various refrigerants revealed that R-410A had the highest heat transfer performance followed by R-l34a, and R-407C had the lowest performance of the refrigerants tested. The pressure drops were also reported in this paper. The pressure drops for R-410A were approximately 45% lower than those of R-l34a. R-407C had 30% lower pressure drops than R-l34a. Experimental results were compared with several correlations which predicted condensation heat transfer coefficients and frictional pressure drops. Comparison with the experimental data showed that the previously proposed correlations gave unsatisfactory results. Based on the present data, empirical correlations of the condensation heat transfer coefficient and the friction factor were proposed.tor were proposed.sed.

• Structural Engineering and Mechanics
• /
• 제5권5호
• /
• pp.541-552
• /
• 1997

In this paper the ultimate strength of the R/C cooling towers, which have initial imperfection and pre-cracked elements, is analyzed. The initial geometric imperfections arise from the unavoidable inaccuracies under the construction and the pre-cracks are assumed to be produced by the temperature stress gradients or cyclic loading under wind pressure and/or earthquake load. Both effects are strongly influenced on the strength of the R/C cooling tower shell structures. The reinforcing ratio is also the important factor to evaluate the ultimate strength of the R/C cooling tower shells. However we could not analyze these structures experimentally because of their large, analyses are the powerful schemes to evaluate the safety and reliability of these structures. The analyzed model is Port Gibson cooling tower shell. In the numerical analysis the geometric and material nonlinearities are taken into account.

• 폴리머
• /
• 제26권2호
• /
• pp.227-236
• /
• 2002

열가역적인 polyvinylidene fluoride (PVDF)/propylene carbonate (PC) 의 매우 묽은 농도에서의 pregel 상태의 구조를 레이저 광산란법으로 조사한 결과 겔형성농도의 100배 이상 묽은 농도 조건에서도 PVDF 사슬은 낱개로 용해되어 있는 것이 아니라 많은 PVDF 사슬들이 응집된 거대한 구형 상태로 존재하며 이때의 응집체의 분산도는 상당히 낮으며 용액온도 $40^{\circ}C$에서 회전반경$R_G$ 는 232 nm, 동력학적 반경 $R_H$는 407 nm로 측정되었다. $R_H/R_G$=1.75의 커다란 비 값, 극소점을 갖는 정적 광산란 패턴 등으로부터 예측하건대 이 응집체의 구조는 core-shell 형태의 구형이며, 이때 내부 core의 반지름은 대략 215 nm, 외부 shell의 두께는 192 nm가 되며, shell 부분에서의 PVDF의 단량체 밀도는 core 부분의 단량체 밀도의 약 75% 수준에 머무르는 것으로 판명되었다.

• 설비공학논문집
• /
• 제16권9호
• /
• pp.855-862
• /
• 2004

This study reports pressure drops during evaporation for R-l34a, R-407C (a mixture of 23 wt% R-32, 25 wt% R-125, and 52 wt% R-l34A) and R-410A (a mixture of 50 wt% R-32 and 50 wt% R-125) in the oblong shell and Plate heat exchanger. The effects of the mass fluxes, heat fluxes, refrigerant saturation temperatures and vapor quality of refrigerants on the measured data were explored in detail. The present data showed that pressure drops of all refrigerants increase with the vapor quality. At a higher mass flux, pressure drops are higher for the entire range of the vapor quality A rise in the heat flux doesn't show significant effects on the pressure drops. Finally, at a higher saturation temperature the pressure drops are found to be lower. The pressure drops for R-407C were approximately 20% lower than those of R-l34a. R-410A had 33% lower pressure drops than R-l34a. Correlation is also provided for the measured pressure drops in terms of the friction factor.

• Asian-Australasian Journal of Animal Sciences
• /
• 제9권6호
• /
• pp.723-726
• /
• 1996

A water loaded pressure device using water as the breaking force was developed to evaluate eggshell strength and compared with a dropping ball techniques. Further, relationships of shell thickness and weight of eggs to shell strength were also studied. Values for both of the shell strength measuring methods showed a highly significant correlation (p < 0.001) with shell thickness. The water loaded pressure method had a much higher simple correlation coefficient for shell thickness (r = + 0.786) than the dropping ball method (r = + 0.577). The shell strength measured by the water loaded pressure method appeared not to be correlated to egg weight. On the other hand, the negative sign of the standard partial regression coefficient and the partial regression coefficient of egg weight in the estimated multiple regression equation implied that for a given shell thickness a larger egg tended to have less shell strength than a smaller egg.

• 설비공학논문집
• /
• 제16권9호
• /
• pp.845-854
• /
• 2004

The evaporation heat transfer coefficient for R-l34a, R-407C (a mixture of 23wt% R-32, 25 wt% R-125, and 52 wt% R-l34a) and R-410A (a mixture of 50 wt% R-32 and 50 wt% R-125) flowing in the oblong shell and plate heat exchanger were investigated experimentally in this study. Four vertical counterflow channels were formed in the exchanger by four plates of commercial geometry with a corrugated sinusoid shape of a chevron angle of 45 degree. The effects of the mean vapor quality, mass flux, heat flux, and saturation temperature of different refrigerants on the evaporation heat transfer were explored in detail. Similar to the case of a Plate heat exchanger, even at a very low Reynolds number, the flow in the oblong shell and plate heat exchanger remains turbulent. It is found that the evaporation heat transfer coefficient in the plates is much higher than that in circular pipes. The present data show that the evaporation heat transfer coefficients of all refrigerants increase with the vapor quality. At a higher mass flux h, is higher than for the entire range of the vapor quality. Raising the imposed wall heat flux was found to slightly improve h$_{r}$, while h$_{r}$ is found to be lower at a higher refrigerant saturation temperature. A comparison of the performance of the various refrigerants reveals that R-410A has the highest heat transfer performance followed by R-l34a, and R-407C had the lowest performance of the refrigerants tested. Based on the present data, empirical correlations of the evaporation heat transfer coefficient were proposed.sed.

• 한국재료학회지
• /
• 제10권6호
• /
• pp.415-421
• /
• 2000

실리카 바인더 함량이 지르콘 쉘 주형의 기계적 특성에 미치는 영향을 고찰하였다. 실리카 졸/지르콘 함량비 $R_w$는 0.18~0.43 범위에서 변화시켰으며, 주형의 소결온도는 $871^{\circ}C~1400^{\circ}C$ 범위에서 변화시켰다. 생형의 상온강도는 실리카 졸/지르콘 함량비 $R_w$에 비례하여 증가하였다. 소결온도가 $1300^{\circ}C$ 이하인 경우, $R_w$가 증가함에 따라 소결된 주형의 상온강도와 치밀화는 증가하였다. 그러나 $R_w$가 0.43이고 $1400^{\circ}C$에서 3시간 동안 소결시킨 경우 주형의 상온강도와 치밀화가 오히려 감소하였다. 이는 소결 중 내화물 입자와 실리카 바인더와 열팽창계수의 차이에 기인하는 것으로 판단된다. 정밀주조용 지르콘 쉘 주형 제작을 의한 최적의 $R_w$ 값은 0.33인 것으로 나타났다.