• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.891-896
• /
• 2000

It is necessary to drill new opening in an existing R.C beam either for service ducts and pipes or the determination of in place concrete strength. Therefore, to simulate in this study, 18-R.C beams were fabricated with circular openings. The major parameters considered are the sizes, location of opening and cut-off stirrup. These beams are tested shear failure and capacity under a point loading. The sizes of opening are changed 0.11, 0.2, 0.3 times of beam-depth and the locations of opening are divided into $X_1$ zone, $X_2$ zone, $X_3$zone. Loads are applied up to failure to observe the cracking initiation and propagation, initial diagonal cracking, midspan deflection. As a result, the sizes of opening with 0.11D and 0.2D in R.C beams without cutoff stirrup are profitable in $X_1$ and $X_3$zone. R.C beams with 0.3D and cutoff stirrup are advantageous in $X_3$zone.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.255-260
• /
• 1994

This study suggests a strengthening effect evaluation technique of reinforced concrete beams using the vibration test. To evaluate the strengthening effect of R/C beams, Strengthening Factor(Sf) was suggested. Using the value of Sf, 20 beams were evaluated. According to these results the effects of R/C beams strengthened by steel plate is superior than those of R/C beams strengthened by carbon fiber sheet.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.776-779
• /
• 2006

The alignment of liquid crystal (LC) is one of the key issues of liquid crystal display (LCD) technologies. In this study, we aligned polyimide (as the LC alignment layer) by ALT plasma beam and to realize the stability and characteristics of this technology. The characteristics such as anchoring energy, pre-tilt angle, voltage holding ratio(VHR) and residual direct current(Rdc) were discussed. Besides, we applied it to the in plane switch (IPS) mode 23" WXGA real panel, the performance parameters and electrical properties were measured and compared with those of rubbing alignment. From the result, we demonstrated a successful LC alignment treatment process in real panel by ALT plasma beam.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.685-690
• /
• 1997

In this study, the behavior of R/C beam strengthened with carbon fiber laminate (C.F.L.) is analyzed from the test results. The purpose of this study is to evaluate the shearing rehabilitation effects of R/C beam with C.F.L. Test parameters are the thickness of C.F.L. and existence of stirrups. Test results how that the shear capacity of specimen without stirrups was increased and shear capacity of specimen with stirrups was not increased due to the insufficient fabrication of specimen and curing.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.515-520
• /
• 1997

This research is aimed at the development of the composite beam-column connection system by which the steel beam can be connected to the R/C column with smooth stress transfer. As the first step of the structural performance tests of the system, bearing resistance test has been carried out for actual size specimen. From the test, the connection system has been proved to take good bonding and stress transfer to the surrounding concrete with negligible relative displacements.

• Journal of Magnetics
• /
• 제10권3호
• /
• pp.108-112
• /
• 2005

GaAs nanowires were grown on GaAs (111)B substrates in a gas source molecular beam epitaxy system, using self-assembled Au particles with diameters between 25 and 200 nm as the catalytic agents. The growth rate and structure of the nanowires were investigated for substrate temperatures between 500 and $600^{\circ}C$ to study the mass transport mechanisms that drive the growth of these crystals. The possibilities for fabrication of novel magnetic nanostructures by suitable choice of growth conditions are discussed.

• Applied Science and Convergence Technology
• /
• 제27권3호
• /
• pp.47-51
• /
• 2018

We fabricated an anode-type ion beam source and studied its driving characteristics of the initial extraction of ions using two driving mechanisms: a diffusion phenomenon and a charge repulsion phenomenon. For specimen exposed to the ion beam in two methods, the surface impurity element was investigated by using X-ray photoelectron spectroscopy. Upon Ar gas injection for plasma generation the ion beam source was operated for 48 hours. We found a Fe 2p peak 5.4 at. % in the initial ions by the diffusion mechanism while no indication of Fe in the ions released in the charge repulsion mechanism. As for a long operation of 200 min, the temperature of ion beam sources was measured to increase at the rate of ${\sim}0.1^{\circ}C/min$ and kept at the initial value of $27^{\circ}C$ for driving by diffusion and charge repulsion mechanism, respectively. In this study, we confirmed that the ion beam source driven by the charge repulsion mechanism was very efficient for a long operation as proved by little electrode damage and thermal stability.

• 센서학회지
• /
• 제5권5호
• /
• pp.69-77
• /
• 1996

Pt/Cr 이중층과 E-beam으로 증착된 산화막으로 구성된 발열체의 발열특성과 열처리 온도에 따른 Pt/Cr 이중층의 전기적, 구조적 특성을 살펴보았다. E-beam으로 증착된 산화막을 갖는 발열체의 표면 방사율(${\varepsilon}$)은 0.5임을 열전대와 I.R. Thermo-Vision System을 통하여 확인할 수 있었다. 한편 열처리전 Pt/Cr의 면저항은 Cr의 두께와는 무관한데, 이는 백금과 크롬의 계면에 형성된 산화크롬에 의한 것으로 사료되며, 열처리 온도가 증가함에 따라 Cr의 외부확산이 증대되고, Pt(220)면의 결정립이 성장함을 AES 분석결과와 SEM 촬영, XRD 분석을 통하여 알 수 있었다. 열처리 온도에 따른 특성 분석결과, $500^{\circ}C$에서 열처리한 Pt/Cr 이중층이 안정된 결정구조를 갖음을 XRD, AES 분석결과로 확인할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제43권1호
• /
• pp.15-30
• /
• 2012

A damped Timoshenko beam element is introduced for the DOF-efficient forced vibration analysis of beam-like structures coated with viscoelastic damping layers. The rotary inertia as well as the shear deformation is considered, and the damping effect of viscoelastic layers is modeled as an imaginary loss factor in the complex shear modulus. A complex composite cross-section of structures is replaced with a homogeneous one by means of the transformed section approach in order to construct an equivalent single-layer finite element model capable of employing the standard $C^{0}$-continuity basis functions. The numerical reliability and the DOF-efficiency are explored through the comparative numerical experiments.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.37-40
• /
• 2006

In this paper, long term deflection of RC beam with variable substitution ratio of recycled aggregate is investigated. 6 RC beam specimens are designed using concrete made of coarse aggregate of 25mm size, mix strength of 21MPa, slump of 12cm and air content of $5.0{\pm}1.5%$. A few concrete blocks are made and used for long term loading. The loading and deflection instrumentation are conducted following the process codified in ACI 318-05 code. Test result shows that the deflection of specimens depends on the compressive strength of concrete. And it is concluded that the deflection of RC beam can be predicted like normal beam using ACI formula if certain level of compressive strength is acquired even recycled aggregate is used in making the beam.