• 대한약학회:학술대회논문집
• /
• 대한약학회 2003년도 Proceedings of the Convention of the Pharmaceutical Society of Korea Vol.2-2
• /
• pp.202.1-202.1
• /
• 2003

Six compounds were isolated from the 90% MeOH fraction of the vine stem of Spatholobus suberectus Dunn (Leguminosae) using silica gel, reverse phase column chromatography and RP-HPLC. Structures of compounds 1-6 were elucidated by spectroscopic parameters of IR, E1 MS, FAB MS, lD-NMR and 2D-NMR spectrum and identified as pseudobaptigenin (1), genistein (2), (2R)-7-hydroxy-6-methoxyflavanone (3), (3R,4R)-2",4"-dihydroxy-6,7-methylenedioxy-isoflavan-4-ol (4), (3R,4R)-7,2" -dihydroxy- 4"-methoxyisoflavan-4-ol (5), sativan (6), respectively. Compounds 3, 4 and 5 have been newly reported in nature.

• 한국전기전자재료학회논문지
• /
• 제32권2호
• /
• pp.165-173
• /
• 2019

Lithium anodes (13, 15, 17, and 20 wt% Li) were fabricated by mixing molten lithium and iron powder, which was used as a binder to hold the molten lithium, at about $500^{\circ}C$ (discharge temp.). In this study, the effect of applied pressure and lithium content on the discharge properties of a thermal battery's single cell was investigated. A single cell using a Li anode with a lithium content of less than 15 wt% presented reliable performance without any abrupt voltage drop resulting from molten lithium leakage under an applied pressure of less than $6kgf/cm^2$. Furthermore, it was confirmed that even when the solid electrolyte is thinner, the Li anode of the single cell normally discharges well without a deterioration in performance. The Li anode of the single cell presented a significantly improved open-circuit voltage of 2.06 V, compared to that of a Li-Si anode (1.93 V). The cut-off voltage and specific capacity were 1.83 V and $1,380As\;g^{-1}$ (Li anode), and 1.72 V and $1,364As\;g^{-1}$ (Li-Si anode). Additionally, the Li anode exhibited a stable and flat discharge curve until 1.83 V because of the absence of phase change phenomena of Li metal and a subsequent rapid voltage drop below 1.83 V due to the complete depletion of Li at the end state of discharge. On the other hand, the voltage of the Li-Si anode cell decreased in steps, $1.93V{\rightarrow}1.72V(Li_{13}Si_4{\rightarrow}Li_7Si_3){\rightarrow}1.65V(Li_7Si_3{\rightarrow}Li_{12}Si_7)$, according to the Li-Si phase changes during the discharge reaction. The energy density of the Li anode cell was $807.1Wh\;l^{-1}$, which was about 50% higher than that of the Li-Si cell ($522.2Wh\;l^{-1}$).

• 대한화장품학회지
• /
• 제24권3호
• /
• pp.73-80
• /
• 1998

This Study was performed to get the suitable oil dispersion agent by assessment of color strength of organic pigment in non-aqueous systems. Organic pigment is used as a color expression material with other body pigments in the make-up products. But occasionally aggregation or agglomeration occurs for the lack of affinity with medium, This function is the cause of disturbing homogeneous dispersion, and then bring about an instability of products. Our study, research of dispersion mechanism between the pigment and oil phase, has been executed to solve this problem, and find a oil dispersion agent having optimum dispersion condition. Generally dispersion is related to between the solid-liquid mutual properties and electrical phenomena associated with solid-liquid interface. This factor is determined to input energy, milling time, optical properties, particle size, rheological properties, etc. Ideal dispersion state is told that coloring primary solid particle is homogeneously dispersed in medium. Good dispersed colorants are strongly and clearly appeared. We are already known that the particle size of organic pigment, chemical properties and viscosity of medium, refractive index. Consequently We determine the affinity of medium and organic pigment by measuring of color strength in the same mechanical condition. UV-VISIBLE RECORDING SPECTRO PHOTOMETER is used for measuring apparatus. We can decided the dispersion level of oil dispersion agent by measuring absorbance of color strength in the visible range that diluted medium for colloid colorant particles.

• 한국전자파학회논문지
• /
• 제22권3호
• /
• pp.389-398
• /
• 2011

본 논문에서는 Ka 대역 위상 배열 레이더용 송수신(T/R: Transmit/Receive) 모듈의 설계 및 제작을 보였다. Ka 대역 송수신 모듈 구성 시 Ka 대역의 특수성을 고려하여 5비트(bit) 위상천이기와 5 비트 30 dB 디지털 가변감쇠기를 송수신 공통으로 사용하였으며, 서큘레이터는 T/R 모듈 외부에 부착되는 형태로 구성하였다. 단위 안테나 당 송신 출력은 1 W 이상 잡음 지수는 8 dB 미만으로 설정하였으며, 설계된 T/R 모듈의 RF부의 크기는 $5\;mm{\times}4\;mm{\times}57\;mm$로 소형화를 달성하였다. 설계된 T/R 모듈을 구현하기 위하여 T/R 모듈에 소요되는 개별 MMIC 검증 후 단위 T/R 모듈을 검증하는 방법을 사용하였다. 제작된 T/R 모듈은 설계 시 예측한 바와 같이 단위 T/R 모듈의 입력 5 dBm에서 출력 30 dBm 이상을 보였으며, 수신부는 잡음 지수 8 dB 미만, 이득 20 dB 이상을 얻었다.

• 공업화학
• /
• 제25권5호
• /
• pp.463-467
• /
• 2014

본 연구에서는 팽창흑연의 함량 변화를 달리하여 제조한 팽창흑연/에리스리톨 복합체의 열적거동에 관하여 고찰하였다. 팽창흑연이 도입된 팽창흑연/에리스리톨 복합체의 표면 및 구조특성은 scanning electron microscope (SEM), transmission electron microscope (TEM), 그리고 X-ray diffraction (XRD)를 이용하여 관찰하였으며, 열적특성은 differential scanning calorimetry (DSC)와 thermal conductivity (TC)를 이용하여 분석하였다. 실험 결과 팽창흑연의 함량이 증가함에 따라 팽창흑연/에리스리톨 복합체의 열전도도가 증가하였으며, 반면에 잠열은 팽창흑연의 존재 하에 약간 감소하였다. 결론적으로 팽창흑연은 상변이 물질의 높은 열 전달성능 및 열 저장능력을 향상시키는데 적합한 소재라 판단된다.

• Journal of Korean Society for Atmospheric Environment
• /
• 제15권E호
• /
• pp.17-28
• /
• 1999

Gas-liquid contact tests above a perforated-plate were conducted with air and water at flooding gas-flow conditions in order to study two-phase flow characteristics in a limestone-gypsum SO2 absorber. Gas layers were in the form of air pockets and confined to the limited areas around each duct pipe, while the remaining tary area were in the wet condition. The liquid above the tray was always in the flooded and even fluidized conditions at gas flows over the range studied, although vigorous bubbly or churn-turbulent two-phase regime was only observed in the immediate vicinity of the gas hole exit at low gas loads. The froth zone was extremely active to provide intimate contact between gas and liquid so that the necessary mass transfer operation can take place, which is the primary purpose of high-performance SO2 absorbers. Howefer, the absorber $\Delta$P was 250mmH2O for the initial water level at 150mm, which is an important issue to be resolved for economical operation of the SO2 absorber. It was seen in the liquid level-and gas flow-transient tests that changes in the absorber liquid inventory were much more pronounced for intimate gas-liquid contact than changes in the gas flow. Based on the 4- and 8-duct pipe test results, grouping the duct pipes near the center of the test tray seemed to promote better recirulation of liquid from gas-liquid contact zone back to the reaction tank so that the absorbed SO2 can be neutralized.

• 대한화장품학회:학술대회논문집
• /
• 대한화장품학회 2003년도 IFSCC Conference Proceeding Book II
• /
• pp.330-342
• /
• 2003

The formation of emulsions and micelles in water/ceramide PC104/CholE $O_{20}$/C$_{16}$E $O_{20}$ and water/ceramide PC104/CholE $O_{20}$ mixtures was investigated through the phase behavior studies. The phase diagrams showed the existence of micelle and emulsion regions in both systems. The mixed surfactant system (CholE $O_{20}$/C$_{16}$E $O_{20}$) showed the wider micellar and emulsion regions than the single surfactant system (CholE $O_{20}$). From FT-IR measurements, it was found that the polyoxyethylene (POE) groups of surfactants formed the hydrogen bonds with amido carbonyl group in ceramide PC104. This result indicated that the hydrophilic part (EO) of surfactants could stabilize the lamellar structure and emulsion of ceramide PC104. The mixed surfactant system (CholE $O_{20}$/C$_{16}$E $O_{20}$) resulted in the smaller emulsion droplet size due to the effect of curvature at the interface, thus further increasing emulsion stability. With the penetration of $C_{16}$E $O_{20}$into the interfacial layer of surfactants in emulsion, the curvature of the interface might be altered for the formation of smaller emulsion droplets. The mixed surfactant system could incorporate up to 4 wt. % of ceramide PC104 into emulsion more than single surfactant system.ystem.m.

• 청정기술
• /
• 제22권4호
• /
• pp.250-257
• /
• 2016

As an attempt to replacing petroleum-based chemicals with bio-based ones, synthesis of furfural from biomass-derived xylose attracts much attention in recent days. Conventionally, furfural from xylose has been produced via the utilization of highly corrosive, toxic, and environmentally unfriendly mineral acids such as sulfuric acid or hydrochloric acid. In this study, microwave-assisted biphasic reaction process in the presence of novel bio-based heterogeneous acid catalysts was developed for the eco-benign and effective synthesis of furfural from xylose. The microwave was irradiated for reaction acceleration and a biphasic system consisting of $H_2O$ : MIBK (1 : 2) was designed for continuous extraction of furfural into the organic phase in order to reduce the undesired side products formed by decomposition/condensation/oligomerization in the acidic aqueous phase. Moreover, sulfonated amorphous carbonaceous materials were prepared from wood powder, the most abundant lignocellulosic biomass. The prepared catalysts were characterized by FT-IR, XPS, BET, elemental analysis and they were used as bio-based heterogeneous acid catalysts for the dehydration of xylose into furfural more effectively. For further optimization, the effect of temperature, reaction time, water/organic solvent ratio, and substrate/catalyst ratio on the xylose conversion and furfural yield were investigated and 100% conversion of xylose and 74% yield of furfural was achieved within 5 h at $180^{\circ}C$. The bio-based heterogeneous acid catalysts could be used three times without any significant loss of activity. This greener protocol provides highly selective conversion of xylose to furfural as well as facile isolation of product and bio-based heterogeneous acid catalysts can alternate the environmentally-burdened mineral acids.

• 한국항행학회논문지
• /
• 제23권5호
• /
• pp.386-391
• /
• 2019

본 논문은 정밀한 전파항법시스템 구현을 위해 안테나의 방향별 군지연 차이가 시스템에 미치는 영향을 분석하였다. 분석은 안테나 시뮬레이션과 시험을 통해서 수행 하였고, 시험은 무반향 챔버에서 진행 하였다. 안테나의 방향별 군지연은 위상(phase)을 기반으로 분석 하였으며, 측정 분석 결과 안테나의 방향별로 최대 약 7.7 ns까지 군지연 차이가 발생했다. 분석된 군지연 차이를 거리로 환산하면 약 2.31 m이며, 이를 실제 TOA (time of arrival)기반의 전파항법시스템에서 시험 하였다. 시험 결과 2.1 m의 거리 변화를 확인 하였으며, 이는 시뮬레이션과 챔버 시험 분석 값과 유사한 수치이다.

• 한국표면공학회지
• /
• 제54권5호
• /
• pp.267-277
• /
• 2021

Nitriding layers developed during gaseous nitriding of AISI4115 steels for the application of steel bushing part were investigated. The compound layer thickness of about 10㎛, 0.3mm of case depth under the same conditions, and conventional nitriding, nitrocarburizing, and controlled nitriding were performed in three methods. In the controlled nitriding, K_N was controlled by measuring the hydrogen partial pressure. The nitrided samples were analyzed by micro Vickers hardness test, optical microscopy and scanning electron microscopy. The phases of compound layer were identified by X-ray diffraction and electron backscatter diffraction. The controlled nitriding specimen indicated the highest surface hardness of about 860 HV_0.1. The compound layer of the conventional nitriding and nitrocarburizing specimen was formed with about 46% porous layer and 𝜺 + 𝜸' phase, and about 13% porous layer and about 80% 𝜸' phase were formed on the controlled nitriding specimen. As a result of the Ball-on-disk wear test, the worn mass loss of ball performed on the surface of the controlled nitriding specimen was the largest. The controlled nitriding specimen had the highest surface hardness due to the lowest porous percentage of compound layer, which improved the wear resistance.