• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권5호
• /
• pp.456-465
• /
• 2016

In order to optimize the performance of a Wells turbine with fixed guide vanes, the designs of an end plate and a ring on the tip of the turbine rotor are proposed as penetrating blade tip treatments. In this study, numerical investigations are made using computational fluid dynamics (CFD)-based ANSYS Fluent software, and validated by corresponding experimental data. The flow fields are analyzed and non-dimensional coefficients $C_A$, $C_T$ and ${\eta}$ are calculated under steady-state conditions. Numerical results show that the stalling phenomenon on a ring-type Wells turbine occurs at a flow coefficient of ${\phi}=0.36$, and its peak efficiency can reach 0.54, which is 16% higher than that of an unmodified turbine and 9% higher than in the case of an endplate-type turbine. In addition, quasi-steady analysis is used to calculate the mean efficiency and output work of a wave cycle under sinusoidal flow conditions. As a result, it has been found that the ring-type turbine is superior to other types of Wells turbines.

• 한국수자원학회논문집
• /
• 제36권6호
• /
• pp.949-960
• /
• 2003

정상상태 가정을 완화시킨 습윤지수의 해상도 문제가 수치지형모형에서 다루어졌다. 반 동역학적 습은지수와 동력학적 습윤지수의 변화성을 수치고도모형의 격자 크기와 배수시간을 변화시키면서, 공간적 통계적으로 고찰하였다. 변화하는 배수시간과 격자크기에 따라 습윤지수의 구조화 양상이 관찰 되었다. 설마천 유역의 적용결과 비교적 짧은 배수시간에서는 습윤도의 천이성이 관찰되었고, 10,000 시간 이상의 배수 시간에서는 통계적 분석 결과가 정상상태의 특성으로 수렴함을 보여주고 있다. 반 동역학적 및 동역학적 습윤지수의 확률밀도 함수들은 계산결과의 안정성과 일관성에 관련이 있는 경계 격자 크기가 존재함을 보여주고 있다.

• International Journal of Aeronautical and Space Sciences
• /
• 제8권1호
• /
• pp.115-121
• /
• 2007

The aeroelastic analysis of rotor blades with trailing edge flaps, focused on reducing vibration while minimizing control effort, are investigated using large deflection-type beam theory in forward flight. The rotor blade aerodynamic forces are calculated using two-dimensional quasi-steady strip theory. For the analysis of forward flight, the nonlinear periodic blade steady response is obtained by integrating the full finite element equation in time through a coupled trim procedure with a vehicle trim. The objective function, which includes vibratory hub loads and active flap control inputs, is minimized by an optimal control process. Numerical simulations are performed for the steady-state forward flight of various advance ratios. Also, numerical results of the steady blade and flap deflections, and the vibratory hub loads are presented for various advance ratios and are compared with the previously published analysis results obtained from modal analysis based on a moderate deflection-type beam theory.

• 한국기계가공학회지
• /
• 제5권1호
• /
• pp.51-58
• /
• 2006

The objective of this research work is to investigate into heat transfer characteristics of the laser cutting of CSP 1N sheet using high power CW Nd:YAG laser. In order to investigate the heat transfer characteristics, three dimensional quasi stationary and steady-state heat transfer analysis has been carried out. The laser heat source is assumed as a volumetric heat source with a gaussian heat distribution in a plane. Through the comparison of the results of analyses with those of experiments, the proper finite element model has been obtained. In addition, characteristics of the three-dimensional heat transfer and temperature distribution have been estimated by the finite element model. Finally, the minimum temperature at the center for cutting of the material has been estimated.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.71-76
• /
• 2008

Nonlinear dynamic system under random excitation was analyzed by using stochastic method. A linearization method was used in order to linearize non-linear structural characteristics but the parametric excitation was used as it was given. An equivalent energy method which equalizes the expectation value of energy of the original nonlinear system and that of quasi-linearized system was proposed. Ito's differential rule was applied to obtain steady state moments. Quasi-linearization coefficients can be obtained the iterative calculation of linearization scheme and steady state moments. Monte Carlo simulation was used to verify the results of the proposed method. Nonlinear vibration of a slender beam was analyzed in this research. The analysis results were compared with Monte Carlo simulation result and showed good agreement. As the spectral density of the given excitation increased, the analysis results showed the better agreement with Monte Carlo simulation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1298-1302
• /
• 2000

Electrorheological(HER) and magnetorheologica(MR) fluids have a unique ability to increase the dynamic yield stress of the fluid substantially when electric or magnetic field is applied. ER and MR fluid-based dampers are typically analyzed using Bingham-plastic shear flow analysis under Quasi-steady fully developed flow conditions. An alternative perspective, supported by measurements reported in the literature, is to allow for post-yield shear thinning and shear thickening. To model these, the constant post-yield plastic viscosity in Bingham model can be replaced with a power-law model dependent on shear strain rate that is known as the Herschel-Bulkley fluid model. The objective of this paper is to predict the damping forces analytically in a typical ER bypass damper for variable electric field, or yield stress using Herschel-Bulkley analysis.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.769-777
• /
• 1999

This paper presents models for the dynamic simulation of a regenerative gas turbine and describes dynamic behaviors of a small regenerative engine. A quasi-steady model is introduced where the inertia of the working fluid is assumed to be negligible compared with the mechanical inertia of the rotating shaft. Based on this quasi-steady model, the transient model for the heat exchanger is employed to simulate the unsteady heat exchange in the recuperator. The effect of the thermal inertia of the recuperator metal on transient behaviors is analyzed by comparing the predicted results of the transient and steady state heat exchanger models. For several load change modes such as sudden increase, decrease and periodic variation, engine dynamic characteristics are investigated by applying a fuel control logic for the constant shaft speed. It is found that the thermal inertia of the recuperator metal has a dominant effect on the whole engine dynamic behavior.

• 상하수도학회지
• /
• 제22권6호
• /
• pp.657-664
• /
• 2008

This research compared several unsteady friction models for transient analysis of pipeline system. Unsteady friction is an important factor for accurate simulation of hydraulic transient. Steady friction, quasi-steady friction, Zielke's model and two versions of Brunone model were compared with measurement data of identical pipeline conditions. This study showed that the existing simple steady friction model can be useful for the safer design of pipeline system due to its overestimation of waterhammer, but introduction of more elaborate models are required for advanced analysis such as inverse transient analysis of friction or leakage and the preliminary analysis of water quality prediction of water distribution system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.381-384
• /
• 1988

This paper analysed basic operation in Zero-voltages-switching quasi-resonant buck converter and considered steady state characteristics. Especially, it is confirmed that converter operating at maximum 1MHz switching frequency in load characteristics. In this paper, a novel slope method is proposed and implemented in regulation characteristics analysis. It is proved that experimenental results coincide with theory results.

• Structural Engineering and Mechanics
• /
• 제12권3호
• /
• pp.267-281
• /
• 2001

Transient and quasi-steady-state vertical vibrations of a multi-span beam steel bridge located on a single-track railway line are considered, induced by a superfast passenger train, moving at speed 120-360 km/h. Matrix dynamic equations of motion of a simplified model of the system are formulated partly in the implicit form. A recurrent-iterative algorithm for solving these equations is presented. Excessive vibrations of the system in the resonant zones are reduced effectively with passive dynamic absorbers, tuned to the first mode of a single bridge span. The dynamic analysis has been performed for a series of types of bridges with span lengths of 10 to 30 m, and with parameters closed to multi-span beam railway bridges erected in the second half of the $20^{th}$ century.