• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1524-1532
• /
• 2015

Conventional space vector pulse width modulation based asymmetrical dual inverter configuration produces high common mode voltage (CMV) variations. This CMV causes the flow of common mode current, which adversely affects the motor bearings and electromagnetic interference of nearby electronic systems. In this study, a simple and generalized carrier based pulse width modulation (PWM) technique is proposed for dual inverter configuration. This simple approach generates various continuous and discontinuous modulating signals based PWM algorithms. With the application of the discontinuous modulating signal based PWM algorithm to the asymmetrical dual inverter configuration, the CMV can be reduced with a slightly improved quality of output voltage. The performance of the continuous and discontinuous modulating signals based PWM algorithms is explored through both theoretical and experimental studies. Results show that the discontinuous modulating signal based PWM algorithm efficiently reduces the CMV and switching losses.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.3
• /
• pp.266-273
• /
• 2012

In this paper, the new open fault detection and tolerant operation method for 3 phase PWM rectifier is proposed. When open fault occurred on the inverter switches of 3 Phase PWM rectifier, the DC link voltage ripple is increased because the input current of the faulty phase is distorted. In this case, the quality of electric power would decrease, and the life time of DC link capacitor is decreased. The open fault is detected by a simple MRAS(Model Reference Adaptive System) without additional hardware sensors, and the tolerant operation carried out by turning on the opposite switch of the faulty switch without any redundancy. By the proposed method, the faulty phase input current can be controlled, so that 3-phase input current is balanced relatively under the faulty condition and the voltage ripple of DC link output is reduced. The validity of the proposed technique is proved on the 6kW 3-phase PWM rectifier system by simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.56-59
• /
• 1988

The main purpose of Set-up control of hot strip mill plant is to obtain the most regular thickness. Then the learning or adaptive computer control in hot strip rolling mill has been developed. But it is very difficult to keep the inter-stands load distribution ratio uniform; so that the deviation of strip flatness is not avoidable. This leads to the degradation of quality of the products. In this report, an improved method base on the steepest descent method including the computation of optimum step size. This method is applied to the off-line simulation. In consequence, the better balances of inter-stands load distribution is achieved in addition to improvements of output thickness of hot strip mill in POSCO.

• Journal of the Korea Safety Management & Science
• /
• v.3 no.3
• /
• pp.151-164
• /
• 2001

Currently, there are little evaluated model for each industry and systematic analysis for each item about current business web sites. And the approach way to improve it all depends on individual. This research is about two different points of view on I-Evaluation development as an approach method to provide analysis, evaluation, and guideline on business web sites. The one is about developing a working step and a site evaluation model that are necessary to improve the quality of site. The other is about a framework development to apply a feedback on site most rapidly and site optimization. The former is from the methodological point of view for I-Evaluation, and the latter is from the point of view for I-Evaluation Framework. In terms of methodology, developing site evaluation model and defining a working step belong to it. Site evaluation model means customizing each customers web site, using each evaluated scoring model which can be a standard for each industry to analyze a similar business web site. Defining a working step means defining input and output parameters for composed elements, working processes, and results analysis on an evaluated model. And also it includes building a working environments to automatic steps mentioned the above by clarifying them.

• Asian Journal of Innovation and Policy
• /
• v.6 no.2
• /
• pp.152-169
• /
• 2017

In this paper, we analyze the basic research system in South Korea. We propose a national basic research system consisting of value, openness, input, transformation, and output. Based on this framework, we set up interview questionnaires, and 15 key informants have been interviewed. According to our results, first, in terms of value, basic research is recognized as an activity for creating knowledge in the understanding of nature. Second, as for openness, scientists and policy experts agree that active interaction with the global community is an important value for the national research system. Third, in terms of sustainable research resources, scientists are strongly required to effectively allocate research funding, maximizing the creativity of researchers and the efficient sharing of research equipment. Fourth, in transformation, basic researchers maintain that the Korean research system has is extremly dependent on the government's external control, and its self-regulative system has been weak for over half century onw. Fifth, for global competitiveness, the interviewees agreed that the quality of basic research in Korea is approaching that of its global competitors. Finally, we put forward some policy implications on the basis of these findings.

• Korean Journal of Optics and Photonics
• /
• v.9 no.3
• /
• pp.175-180
• /
• 1998

Nd:YAG single crystal widely used as solid state laser was grown by Czochralski method. <111> single crystal with 0.9at% of $Nd^{3+}$ was grown from the Czochralski furnace with a automatic diameter control system. The vertical temperature gradient in the liquid was the major factor that influence the crystal quality, and the crystal diameter was controlled by the home made computer program. The crystal boule with $\phi$50mm$\times$ι100mm effective size was cut, polished, and antireflection coated. The optical evaluation such as absorption spectrum, fluorescence spectrum coincide with typical features of Nd:YAG single crystal. The laser rod was assembled into the CW laser generator with a Kr lamp. The maximum CW laser output was 70 W and the threshold power and efficiency was 1.3kW and 1.64% respectively.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.663-671
• /
• 2014

LED lamp arrangement is a critical issue in indoor visible light communication (VLC) system. In this paper, we analyze the illumination distribution under the arrangement of $2{\times}3$ and propose a method to find the optimal lamp arrangement. The method, based on the MIMO (Multiple Input/Multiple Output) system model and taking the first order reflection into consideration, enables accurate analysis of the arrangement of the LED lamps for any room. The studies show that under the optimal arrangement the uniformity of illumination is improved from 0.55 to 0.86, which guarantees that users can get almost equal lighting effects, no matter where they locate themselves. At the same time, the RMS delay spread distribution which is used to evaluate the inter-signal-interference (ISI) is analyzed, and the simulation results indicate that the optimal arrangement also can improve the communication quality by reducing the fluctuation of the RMS delay spread.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.792-795
• /
• 1996

In TIG welding of pipe, back bead size monitoring is important for weld quality assurance. Many researches have been performed on estimation of the back bead size by heat conduction analysis. However numerical conduction model based on many uncertain thermal parameters causes remarkable errors and thermomechanical phenomena in molten pool can not be considered. In this paper, filler wire feeding force in addition to weld current, wire feedrate, torch travel speed and orbital position angle is monitored to estimate back bead size in orbital TIG welding. Monitored welding process variables are fed into an artificial neural network estimator which has been trained with the monitored process variables (input patterns) and actual back bead size (output patterns). Experimental verification of the proposed estimation method was performed. The predicted results are in a good agreement with the actual back bead shape. The results are quite promising in that estimation of invisible back bead shape can be achieved by analyzing the welding parameters without any conventional NDT of welds.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.8
• /
• pp.923-931
• /
• 1999

In this paper, a modeling and a robust time-delay control for the reclaimer are investigated. Supplying the same amount of a raw material throughout the reclamation process from the raw yard to a sinter plant is important to keep the quality of the molten steel uniform in blast furnaces. As the actual parameter values of the reclaimer are not available, the boom rotational dynamics are modeled as a second order differential equation with unknown coefficients. The unknown parameters in the nominal model are estimated using a recursive estimation method. Another important factor in the control design of the reclaimer is the large time-delay in output measurement. Assuming a multiplicative uncertainty, that accounts for both the unstructured uncertainty neglected in the modeling and the structured uncertainty contained in the parameter estimation, a robust Smith predictor is designed. A robust stability criterion for the multiplicative uncertainty is also derived. Following the work of Goodwin et al. [4], a quantifying procedure of the multiplicative uncertainty bound, through experiments , is described. Experimental and simulation results are provided.

• Journal of Korea Port Economic Association
• /
• v.24 no.1
• /
• pp.85-102
• /
• 2008

The purpose of this study is to analyze the effects of Logistic Information System on performance by efficiency of internal operation and organizational innovation. The results of this study as follows : The characteristic variable evaluation model that extended from the performance(user's value, perceived usefulness) of Logistic Information System were verified meaningfully. In this study, the efficiency of internal operation and organizational innovation were very important factor, to analyze the effects of Logistic Information System on performance. This study expect that Logistic Information System will achieve their Logistic Information System competitiveness through continuous quality measurement and improvement to increase the performance.