• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.243-246
• /
• 2006

현재의 많은 유도무기들은 발사관에 장착되어 보관 및 이동되다가 필요시 발사된다. 발사관이란 유도탄 즉 미사일등이 외부환경에 노출되지 않도록 유도탄을 둘러싸고 있는 일종의 케이스이며 또한 유도탄 발사시 가이드 역할을 동시에 수행한다. 유도탄과 발사관을 연결하는 방법으로 흔히 사용되는 것으로 탄고정장치를 사용하는데 대표적인 파이로 부품이 폭발볼트이다. 폭발볼트는 화약의 폭발력에 의해 볼트몸체가 이등분됨으로써 볼트에 의해 결합되고 있던 부분이 분리된다. 하지만 기존의 폭발볼트는 분리시 파편, 화염 및 pyre-shock이라는 악작용을 수반하므로 사용상 제한을 가지고 있다. 이와 같은 문제점을 해결하기 위하여 ball을 이용한 결합 분리장치 즉 ball type 분리볼트를 개발하게 되었다. 기존의 폭발볼트가 가졌던 기계적 우수성은 물론 분리시 파편, 화염 및 pyre-shock이 발생되지 않는 장점을 가지고 있는 것으로 판단된다.

• 전기학회논문지
• /
• 제67권3호
• /
• pp.433-439
• /
• 2018

In this paper, a SDINS(strapdown inertial navigation system) rapid initial alignment technique with adaptive time delay compensation is proposed. The proposed method consists of two steps. In first step, misalignment and data latency are estimated by conducting pre-transfer alignment. Then, hybrid alignment is designed to rapidly find the misalignment changes induced by pyro-shock. To improve the performance of hybrid alignment, adaptive time delay compensation method is suggested. We verify the performance improvement of the proposed alignment scheme comparing with the conventional transfer alignment method by van test. The test result shows that the proposed alignment technique improves alignment performance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1234-1239
• /
• 2000

KOMPSAT-1(Korea Multi-Purpose Satellite), which opened the space era in Korean peninsula, was developed from 1994 and launched successfully in December of 1999 at VAFB, USA. This paper presents a launch environment test of KOMPSAT and a short description of environment test facilities at Korea Aerospace Research Institute as well. The launch environment tests of KOMPSAT-1 satellite, such as vibration, acoustic, pyro-shock and mass properties measurement test, were performed during its system integration and test period. The participating engineers concluded that KOMPSAT-1 satellite would withstand environment during its launch period.

• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.401-406
• /
• 2013

Non-explosive shockless holding and release mechanism for a nano class small satellite application has been proposed and investigated. The great advantages of the mechanism are a much lower shock level and larger constraint force than the conventional mechanism using pyro and the heating wire cutting mechanism which has been generally applied to the cube satellite program. To investigate the effectiveness of the mechanism design, EM mechanism was developed and tested to verify the basic function of the mechanism. The test results indicate that the proposed mechanism is well functioning as the mechanism design intends.

• 한국추진공학회지
• /
• 제15권2호
• /
• pp.62-67
• /
• 2011

현재의 많은 유도무기들은 발사관에 장착되어 이동된다. 발사관이란 유도탄등이 외부환경에 노출되지 않도록 유도탄을 보호하고, 발사시 유도탄을 가이드 하는 역할을 한다. 발사관에 장착되어 있는 유도탄은 발사관에 견고하게 장착되어 이동되어야 하며, 작전시 원하는 시간에 분리되어야 한다. 이를 위하여 구조적인 안전성이 크고, 분리 응답이 빠른 파이로 장치인 폭발볼트가 많이 사용된다. 폭발볼트는 화약의 폭발력에 의해 볼트몸체가 절개됨으로써 볼트에 의해 결합되고 있던 부분이 분리되는데, 폭발 볼트는 분리시 파편, 화염 및 pyro-shock이라는 큰 진동과 충격을 수반하므로 정밀한 유도무기에는 사용이 제한된다. 이와 같은 문제점을 해결하기 위하여 압력카트리지에서 발생하는 압력을 분리력으로 사용하여, 충격이 작고, 분리파편이 발생하지 않는 분리장치인 볼타입 분리볼트를 개발하였다. 본 연구에서는 볼타입 볼트의 분리현상을 분석하고, 볼타입 분리볼트의 분리 안전율을 정량적으로 제시하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.208-211
• /
• 2007

분리장치란 두개의 구조물을 결합하고 필요에 의해 분리할 수 있는 기능을 가진 장치이다. 본 논문은 이와 같은 기능을 화약의 폭발 및 연소시 발생하는 에너지를 이용하여 수행하는 파이로테크닉 수에 관한 것이다. 화약의 폭발력에 의해 분리가 이루어지는 분리장치로는 폭발볼트가 있다. 폭발볼트의 경우 작동 개념이 단순하고 또한 구성 부품의 수가 적기 때문에 신뢰성 면에서 뛰어나지만 분리시 파편 및 파이로 충격을 동반하는 단점이 있다. 이와 같은 단점을 보완하기 위하여 개발된 것이 가스팽창분리 볼트와 압력카트리지 작동분리장치이다. 이들 장치는 화약의 연소시 발생되는 압력을 이용하기 때문에 분리시 폭발볼트와 같은 악작용은 없지만 폭발볼트에 비해 사이즈가 대형이거나 기계적 결합강도가 작다는 단점이 있다. 따라서 위에 언급된 분리장치들의 작동 원리 및 특성을 이해함으로써 분리장치 설계시 최적의 사양을 선택하는 것이 가능하다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.63-67
• /
• 2007

The high pressure turbopump carries out supplying the oxidizer in the liquid propulsion rocket in the combustion chamber. Because an LRE requires a very short starting time , the turbine at the turbopump experiences high torque that was produced by the high pressure and the high temperature. The purpose of this study is to evaluate a turbine blade surface temperature profiles at initial starting 0 ${\sim}$ 0.5 sec. Using $Fine^{Tm}$/turbo, three dimensional Baldwin-Lomax turbulence models are used for numerically analysis. The turbine is composed of 108 blades total, but only 7 rotors were considered because of periodic symmetry effect. Because of interaction with a bow shock on the suction surface, the boundary layer separates from suction surface at inner area of turbine blade. The averaged temperature of the turbine blade tip at 1000 rpm is higher than that of 9000 rpm. Especially at 1000 ${\sim}$ 9000 rpm, temperatures increases on the hub side of the turbine blade tip. Moreover at 9000 rpm, the temperatures from the hub to the shroud of the blade tip increase as well.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.911-915
• /
• 2014

Pyrotechnic devices are widely used for space appendages. However, a cube satellite requirements do not permit the use of explosive pyrotechnic device. A nichrome burn wire release has typically been used for holding and release of deployable appendages of the cube satellite due to its simplicity and low cost. However, relatively low mechanical constraint force and system complexity for application of multi-deployable systems are disadvantages of the conventional mechanism. To overcome these drawbacks, we have developed a segmented nut type holding and release mechanism based on the nichrome burn wire release. The great advantages of the mechanism are much lower shock level and larger constraint force than the conventional mechanism using pyro. Flight model for on-orbit verification was developed and verified through release function test, vibration test and thermal vacuum test.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.534-539
• /
• 2009

Reaction Bonded Silicon Carbide(RBSC) has been used for engineering ceramics due to low-temperature fabrication and near-net shape products with excellent structural properties such as thermal shock resistance, corrosion resistance and mechanical strength. Recently, attempts have been made to develop hot gas filter with gradient pore structure by RBSC to overcome weakness of commercial clay-bonded SiC filter such as low fracture toughness and low reliability. In this study a fabrication process of porous RBSC with multi-layer pore structure with gradient pore size was developed. The support layer of the RBSC with multi-layer pore structure was fabricated by conventional Si infiltration process. The intermediate and filter layers consisted of phenolic resin and fine SiC powder were prepared by dip-coating of the support RBSC in slurry of SiC and phenol resin. The temperature of $1550^{\circ}C$ to make Si left in RBSC support layer infiltrate into dip-coated layer to produce SiC by reacting with pyro-carbon from phenol resin.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.813-822
• /
• 2008

The present work has been developed the interpretation processor including analysis of the failure stress in pyrotechnically releasable mechanical linking device, which has the release characteristic without fragmentation and pyro-shock, using SoildWorks, COSMOS Works and ANSYS programs. The aim of the invention is to propose a pyrotechnically releasable mechanical linking device for two mechanical elements that does not suffer from such drawbacks. The pyrotechnically releasable mechanical linking device according to the invention is simple, compact and inexpensive in structure. It is simple to implement and permit the use of only a reduced quantity of pyrotechnic composition, such composition possibly being devoid of any primary explosive at all. The present work is only focused on the design of structure and the material characteristics. To analyze the fracture morphology resulted from tensile test in the different ball type bolts, the present work has been performed to estimate the failure stress of material and to make the same result from tensile test. The failure stress of SUS 630 in ductile material is approximately 1050 Mpa. The failure stress of SUS 420 in brittle material is about 1790 Mpa. Among the models used the ductile material, the model 6 is suitable a design of structure compared to that of other models. The use of this interpretation processor developed the present work could be extensively helped to estimate the failure stress of material having a complex geometry such as the ball type bolt