• Title/Summary/Keyword: Pure Iron

Search Result 192, Processing Time 0.028 seconds

Analysis of the Sliding Wear Mechanism of Pure Iron Tested Against Different Counterparts in Various Atmospheres (상대재와 분위기에 따른 순철의 미끄럼 마멸 기구 분석)

  • Koo, B.W.;Gwon, H.W.;Kim, Y.S.
    • Transactions of Materials Processing
    • /
    • v.26 no.6
    • /
    • pp.365-371
    • /
    • 2017
  • During sling wear of a ferrous metal, a surface layer is formed. Its microstructure, constituting phases, and mechanical property are different from those of the original wearing material. Since wear occurs at the layer, it is important to characterize the layer and understand how wear rate changes with different layers. Various layers are formed depending on external wear conditions such as load, sliding speed, counterpart material, and environmental conditions. In this research, sliding wear tests of pure iron were carried out against two different counterparts (AISI 52100 bearing steel and $Al_2O_3$) in the air and in an inert Ar gas atmosphere. Pure iron was employed to exclude other effects from secondary phases in steel on the wear. Wear tests were performed at room temperature. Worn surfaces, wear debris, and cross-sections were analyzed after the test. It was found that these two different counterparts and environments produced diverse layers, resulting in significant changes in wear rate. Against the bearing steel, pure iron showed higher wear rate in an Ar atmosphere due to severe adhesion than that in the air. On the contrary, the iron showed much higher wear rate in the air against $Al_2O_3$. Different layers and wear rates were analyzed and discussed by oxidation, severe plastic deformation, and adhesion at wearing surfaces.

The Pitting Inhibition of Fe-Cu Alloy in Weakly Alkaline Solution under Wet-Dry Condition

  • Kim, Je-Kyoung;Kang, Tae-Young;Moon, Kyung-Man
    • Journal of the Korean Electrochemical Society
    • /
    • v.10 no.3
    • /
    • pp.175-178
    • /
    • 2007
  • Pure iron, Fe-0.4, and 1.2 wt.%Cu alloys were examined by conducting the electrochemical techniques in the weakly alkaline solution, pH9, controlled by $Ca(OH)_2$, solution added with 0.02M NaCl. The $R_P$ measured from ac impedance, selected 10 kHz and 10mHz, in weakly alkaline solutions containing chloride ions indicated that the addition of copper up to 1.2wt.% into the pure iron significantly improved the pitting resistance of iron. In contrast to alloy, the pure iron showed the rapid pitting occurrences in drying period. During the drying period, the corrosion potential of pure iron was shifted to less noble value, pitting initiation.

A Study on the Influence of Pure Iron Purity of Electric Lens on the Electron Beam Control (전자빔 가공기의 전자렌즈 순철순도가 빔 제어에 미치는 영향)

  • Lee Chan-Hong;Ro Seung-Kook
    • Proceedings of the Korean Society of Precision Engineering Conference
    • /
    • 2005.10a
    • /
    • pp.149-153
    • /
    • 2005
  • The electron beam machining provides very high resolution up to nanometer scale, hence the E-beam writing technology is rapidly growing in MEMS and nano-engineering areas. In the optical column of the e-beam writer, there are several lenses condensing and focusing electron beams from electron gun with fringing magnetic fields. The polepieces of these lenses are usually made with high purity iron which is hard to fabricate and very expensive. In this paper, the possibility of using polepiece of object lens composed with pure iron and low carbon steel was examined to reduce cost. The magnetic field at object lens was calculated with finite element method, and practical focusing qualities of SEM pictures were observed comparing for the object lens polepieces with pure iron and two type of composed with low carbon steel.

  • PDF

A Study on Flat Iron Axe Manufacturing Technology Using Metallurgical Analysis - Focused on the Artifacts Excavated from the Hadae Ancient Tombs in Ulsan - (금속학적 분석을 통한 판상철부의 제작기술 연구 - 울산 하대고분 출토 유물을 중심으로 -)

  • Jo, Hanui;You, Halim;Lee, Jaesung
    • Korean Journal of Heritage: History & Science
    • /
    • v.52 no.3
    • /
    • pp.240-251
    • /
    • 2019
  • This study examined the manufacturing technology used for the flat iron axes excavated from Ulsan Hadae. Their microstructures were analyzed using metallurgical methods. In addition, a variety of manufacturing technologies were examined and compared using existing research materials on flat iron axes. As a result of analyzing ten flat iron axes, which were excavated in the order that they were laid out in a row in one of the wooden coffin tombs at Ulsan Hadae, Tomb No. 44, it was possible to classify the flat iron axe manufacturing technology and system into three types: 'pure iron - shape processing', 'pure iron - shape processing - carburizing', and 'pure iron - shape processing - carburizing - decarburizing.' All of the flat iron axes were produced by forging, and most of them were made by beating the pure iron into their shapes. In particular, a number of the flat iron axes were reinforced through a carburizing process after shaping the iron. This appears as steel products forming the basis of the steel industry at the time were commonly used as an intermediary material or currency. On the other hand, it was commonly found in all samples that the hardening was not performed after shaping or carburizing. Since the microstructure of the flat iron axes made of pure iron contained a large number of impure inclusions and the result of analyzing the components of the non-metal inclusions showed characteristics of slag which contains a mixture of glass phase and wustite, it is possible that low-temperature reduction was used in the refining process.

A Study on the Carburization Mechanism of Iron by Solid Carbon (고체탄소(固體炭素)에 의한 철(鐵)의 침탄기구(浸炭機構)에 대(對)한 연구(硏究))

  • Kwon, Ho-Young;Cho, Tong-Rae;Kang, Sei-Sun
    • Journal of Korea Foundry Society
    • /
    • v.8 no.3
    • /
    • pp.287-295
    • /
    • 1988
  • The experiment was carried out for the purpose of studying the carburization of pure iron ingot and sintered iron powder by solid carbon in the atmosphere of CO gas. The volocity of carburization was estimaed by the diffusion coefficient D calculated by carburization equation. The results obtained were as follow: 1. The higher the carburization temperature, carburization depth and carbon concentration were increased, and the melting zone which had $2.8{\sim}3.4%C$ at the $3{\sim}4mm$ from interface of carburization was formed at $1300^{\circ}C$. 2. The main carburization mechanism of pure iron ingot and the sintered iron powder were proceeded by CO gas up to $1100^{\circ}C$, solid carbon over than $1300^{\circ}C$, respectively. 3. The main carburization mechanism of pure iron ingot at $1200^{\circ}C$ was proceeded by solid carbon, and sintered iron powder was proceeded bs CO gas, however, in case the reaction time, the carburization was proceeded by solid carbon over than 5hrs. 4. The diffusion coefficient D of carbon were $0.559{\times}10^{-6}cm^2.sec^{-1}$ at $1100^{\circ}C$, $0.237{\times}10^{-6}cm^2.sec^{-1}$ at $1200^{\circ}C$, $0.087{\times}10^{-6}cm^2.sec^{-1}$ at $1300^{\circ}C$, in case of pure iron ingot carburized. 5. The diffusion coefficient D of carbon were $0.124\;cm^2.sec^{-1}$ at $1100^{\circ}C$, $0.102\;cm^2.sec^{-1}$ at $1200^{\circ}C$, $0.480\;{\times}10^{-6}cm^2.sec^{-1}$ at $1300^{\circ}C$, in the case of sintered iron carburized at the pressuring $4ton\;/\;cm^2$.

  • PDF

A Study on the Carburization of iron (철의 침탄기구에 대한 연구)

  • 권호영;조통래;권혁무
    • Journal of the Korean Professional Engineers Association
    • /
    • v.20 no.4
    • /
    • pp.5-11
    • /
    • 1987
  • The experiment was carried out for the purpose of studying the carburization of pure iron ingot and sintered iron powder by solid carbon in the atmosphere of $N_2$ gas. The velocity of carburization was estimated by the diffusion coefficient D calculated by carburization equation. The results obtained were as follows ; 1. The briqueted sample of iron fine powder which made by higher pressure, carburization depth and carbon concentration were increased as much, and pure iron shelved the maximum value. 2, The higher the carburization temperature, carburization depth and carbon concentration were increased, and the melting zone which had 3.0~3.3%C at the interface of carburization was formed at 130$0^{\circ}C$. As the pure iron ingot was carburized, the diffusion coefficient D of carbon were 0.211$\times$$10^{-6}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 120$0^{\circ}C$ and 0.391$\times$$10^{-6}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 130$0^{\circ}C$, respectively. 4. As the sintered iron powder was carburized at the pressure of 4 ton/$\textrm{cm}^2$, the diffusion coefficient of carbon were 0.157$\times$$10^{-6}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 120$0^{\circ}C$ and 0.103$\times$$10^{-5}$$\textrm{cm}^2$ㆍsec$^{-1}$ at 130$0^{\circ}C$, respectively.

  • PDF

Study on the Spheroidizing Mechanism of Graphite in Cast Iron (II) (鑄鐵에 있어서의 黑鉛球狀化 機構에 關한 硏究 (Ⅱ))

  • Choi, Hyung-Sup;Park, Won-Koo
    • Journal of the Korean Chemical Society
    • /
    • v.8 no.2
    • /
    • pp.57-61
    • /
    • 1964
  • It was verified at Part Ⅰ of this investigation that there is a minimum wettability between molten iron and graphite, which was preliminarily coated with magnesium, and thus the spheroidization of graphite might have resulted from the lack of wettability between magnesium-adsorbed graphite and iron matrix. Being continued from the last work, the wettability between pure iron and graphite, coated with the various thickness of cerium, are measured at melting point of pure iron in vacuum and 200 mmHg argon gas atmosphere. The result indicates the presence of a minimum wettability at a critical thickness of cerium film as was proved in the case of magnesium. The experimental analysis shows that, the minimum wettability could be attributed entirely to a minimum work of adhesion between liquid iron and graphite at a critical concentration of cerium in the iron-graphite interface.

  • PDF

Controlling the Heat Generation Capability of Iron Oxide-Base Nanoparticles (산화철 나노 입자의 발열 효과의 제어)

  • Choi, Jin-sil
    • Journal of Powder Materials
    • /
    • v.28 no.6
    • /
    • pp.518-526
    • /
    • 2021
  • This review summarizes the recent progress in iron-oxide-based heat generators. Cancer treatment using magnetic nanoparticles as a heat generator, termed magnetic fluid hyperthermia, is a promising noninvasive approach that has gained significant interest. Most previous studies on improving the hyperthermia effect have focused on the construction of dopant-containing iron oxides. However, their applications in a clinical application can be limited due to extra dopants, and pure iron oxide is the only inorganic material approved by the Food and Drug Administration (FDA). Several factors that influence the heat generation capability of iron-oxide-based nanoparticles are summarized by reviewing recent studies on hyperthermia agents. Thus, our paper will provide the guideline for developing pure iron oxide-based heat generators with high heat dissipation capabilities.

Friction Welding of Spheroidal Graphite Cast Iron and 2024 Aluminium Alloys using Insert Metal (삽입금속을 사용한 구상흑연주철과 2024 알루미늄합금의 마찰압접에 관한 연구)

  • KIM CHANG-GYU;KIM CHI-OK;KIM KWANG-ILL
    • Journal of Ocean Engineering and Technology
    • /
    • v.17 no.5 s.54
    • /
    • pp.76-81
    • /
    • 2003
  • Friction welding of GCD45 spheroidal graphite cast iron and 2024 aluminum alloy has been studied, especially in terms of the joint faces and strength of friction welding. For appropriate results of the friction welding of GCD45 graphite cast iron and 2024 aluminum alloy, an insert of A1050 pure aluminum metal was used. The joint strength of the A1050 pure aluminum insert approached the maximum strength of 165.7Mpa, compared to 128MPa for the joint between GCD45 graphite cast iron and A1050 pure aluminum without the insert metal. Maximum strength, 165.7Mpa, was possible for the following optimum conditions: 20MPa for the friction pressure, P1, 60MPa for the upsetting pressure, P2, 1 second for the friction time, t1, 3000rpm for the rotation, N, and 0.3 seconds for the brake time, tB.

Metallurgical Study of Iron Artifacts Yangju-Mountain Fortress (양주 대모산성 출토 철기유물의 금속학적 연구)

  • Lim, Sun-Ki;Kang, Dai-Ill;Moon, Whan-Suk;Park, Dong-Kyu;Kang, Sung-Goon
    • 보존과학연구
    • /
    • s.14
    • /
    • pp.1-34
    • /
    • 1993
  • 1. Metallurgical Properties of Iron artifacts excavated from Yangju-Mountain fortress were studied for the scientific conservation and metallurgical history of ancient Iron artifacts.2. Iron artifacts form Yangju-Mountain fortress were found to be the products of having well-established Carburizing and remelting technique in that period.3. These artifacts seem to be manufactured from very pure ores, because very pure ferrite structure and low impurity.4. Especially evidence of very suitable carburizing technic well-established and usealloying method of Fe-C system on purpose were found.5. Cast iron artifacts were found to be eutectic composition (4.31%) having lowestmelting point in Fe-C system.

  • PDF