• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.5
• /
• pp.452-459
• /
• 2010

This study is aimed to investigate changes of combustion characteristics and heat efficiency when syngas from gasification process using low-rank fuel such as waste and/or biomass is applied partially to an industrial boiler. An experimental study on syngas co-combustion was performed in a 0.7 MW (1 ton steam/hr) water tube boiler using heavy oil as a main fuel. Three kinds of syngas were used as an alternative fuel: mixture gas of pure carbon monoxide and hydrogen, syngas of low calorific value generated from an air-blown gasification process, and syngas of high calorific value produced from an oxygen-blown gasification process. Effects of co-combustion ratio (0~20%) for each syngas on flue gas composition were investigated through syngas injection through the nozzles installed in the side wall of the boiler and measuring $O_2$, $CO_2$, CO and NOx concentrations in the flue gas. When syngas co-combustion was applied, injected syngas was observed to be burned completely and NOx concentration was decreased because nitrogen-containing-heavy oil was partially replaced by the syngas. However, heat efficiency of the boiler was observed to be decreased due to inert compounds in the syngas and the more significant decrease was found when syngas of lower calorific value was used. However, the decrease of the efficiency was under 10% of the heat replacement by syngas.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.7
• /
• pp.275-281
• /
• 2003

$Zn_{0.5}Cd_{0.5}Al_{2}Se_{4}$ and $Zn_{0.5}Cd_{0.5}Al_{2}Se_{4}$:$Co^{2+}$ single crystals were grown by CTR method. The grown single crystals have defect chalcopyrite structure with lattice constant a=5.5966$\AA$, c=10.8042$\AA$ for the pure, a=5.6543$\AA$, c=10.8205$\AA$ for the Co-doped single crystal, respectively. The optical energy band gap was given as indirect band gap. The optical energy band gap was decreased according to add of Co-impurity Temperature dependence of optical energy band gap was fitted well to the Varshni equation. From this relation, we can deduced the entropy, enthalpy and heat capacity. Also, we can observed the Co-impurity optical absorption peaks assigned to the $Co^{2+}$ ion sited at the $T_{d}$ symmetry lattice and we consider that they were attributed to the electron transitions between energy levels of ions.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.36 no.1
• /
• pp.17-32
• /
• 2010

This review shows the design and the development of new $CO_2$-soluble hydrocarbon copolymers which can be used as effective stabilizers for successful dispersion polymerizations of bio-compatible materials in supercritical carbon dioxide ($scCO_2$). The basic concepts of supercritical fluid including its solvent properties and applications in polymer synthesis are described. We report the facile synthesis of highly soluble hydrocarbon based copolymers, prepared with good control via controlled free radical polymerization from readily accessible and commercially available monomers. The phase behaviour of these materials was monitored in pure $CO_2$ to investigate how the molecular weights and the composition of the copolymers affect their solubility in $CO_2$. Their activity as a stabilizer was then tested in dispersion polymerization of N-vinyl pyrrolidone in $CO_2$ at various reaction conditions to identify the key parameters required for a successful dispersion stabilization of growing PVP particles. Some prospective potentials of this research which can be applied in developing new polymer materials in an environmentally-friendly fashion for use in cosmetics are also discussed.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.220-225
• /
• 2022

Perlite is one of the major constituents of the radioactive thermal insulation waste (RTIW) originating from nuclear power plants and, for proper waste management, a significant reduction in its volume is required prior to disposal. In this work, the volume reduction of perlite is studied by high-temperature treatment method with using K₂CO₃ as a flux. The perlite is ground with 0-30 wt% K₂CO₃, and differential thermal analysis/thermogravimetric analysis is used to monitor the glass transition temperature (T_g) and weight loss. The Tg varied between ~772.2 and 837.1 ℃ with the minima at ~643.5 ℃ with the addition of ~10 wt% K₂CO₃. It is observed that compared to the pure perlite the volume reduction ratio (VRR) increases with the addition of K₂CO₃. The VRR of 11.20 is observed with 5 wt% K₂CO₃ at 700 ℃, as compared to VRR of 5.56 without K₂CO₃ at 700 ℃. The X-ray photoelectron spectroscopy and scanning electron microscopy are used to characterize perlite samples heat-treated without/with 5 wt% K₂CO₃ at 700 ℃. Moreover, the atomic absorption spectroscopy indicates that the proposed heat-treatment procedure is able to completely retain the radionuclides present in the perlite RTIW.

• ETRI Journal
• /
• v.32 no.6
• /
• pp.891-900
• /
• 2010

In this paper, a map-matching (MM) algorithm which combines an estimated position with digital road data is proposed. The presented algorithm using a virtual track is appropriate for a MEMS-based pedestrian dead reckoning (PDR) system, which can be used in mobile devices. Most of the previous MM algorithms are for car navigation systems and GPS-based navigation system, so existing MM algorithms are not appropriate for the pure DR-based pedestrian navigation system. The biggest problem of previous MM algorithms is that they cannot determine the correct road segment (link) due to the DR characteristics. In DR-based navigation system, the current position is propagated from the previous estimated position. This means that the MM result can be placed on a wrong link when MM algorithm fails to decide the correct link at once. It is a critical problem. Previous algorithms never overcome this problem because they did not consider pure DR characteristics. The MM algorithm using the virtual track is proposed to overcome this problem with improved accuracy. Performance of the proposed MM algorithm was verified by experiments.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.5
• /
• pp.1491-1494
• /
• 2011

Lithium vanadium phosphate, $Li_3V_2(PO_4)_3$ was prepared by a simple solid state route. It was found that making a fine powder of $Li_3V_2(PO_4)_3$ by the mechanical milling is very effective for increasing the insertion/extraction of lithium from $Li_3V_2(PO_4)_3$ structure. In charge/discharge test, the ball-milled $Li_3V_2(PO_4)_3$ sample exhibited a higher initial discharge capacity of 174 mAh/g in the voltage range of 3.0-4.8 V, compared with pure $Li_3V_2(PO_4)_3$ sample (152 mAh/g). Furthermore, the ball-milled $Li_3V_2(PO_4)_3$ presented not only higher cycle retention rate after 50 cycles, but also better rate capability compared with pure sample in the whole region (0.1-7 C).

• Journal of Powder Materials
• /
• v.9 no.3
• /
• pp.174-181
• /
• 2002

Nanosized tungsten carbide powders were synthesized by the chemical vapor condensation(CVC) process using the pyrolysis of tungsten hexacarbonyl($W(CO)_6$). The effect of CVC parameters on the formation and the microstructural change of as-prepared powders were studied by XRD, BET and TEM. The loosely agglomerated nanosized tungsten-carbide($WC_{1-x}$) particles having the smooth rounded tetragonal shape could be obtained below $1000^{\circ}C$ in argon and air atmosphere respectively. The grain size of powders was decreased from 53 nm to 28 nm with increasing reaction temperature. The increase of particle size with reaction temperature represented that the condensation of precursor vapor dominated the powder formation in CVC reactor. The powder prepared at $1000^{\circ}C$ was consisted of the pure W and cubic tungsten-carbide ($WC_{1-x}$), and their surfaces had irregular shape because the pure W was formed on the $WC_{1-x}$ powders. The $WC_{1-x}$ and W powders having the average particles size of about 5 nm were produced in vacuum.

• Carbon letters
• /
• v.5 no.4
• /
• pp.159-163
• /
• 2004

The polymer-ceramic hybrid, known as 'ceramer', was synthesized by a sol-gel process by incorporating different amount of alkoxide as source of silicon in resorcinol-formaldehyde in presence of basic catalyst to get different percentage of silicon in ultimate carbonized composites. FTIR of the ceramer confirms that it is a network of Si-O-Si, Si-O-$CH_2$ and Si-OH type groups linked with benzene ring. Different amount of silicon in the ceramer exhibits varying temperature of thermal stability and lower coefficient of thermal expansion as compared to pure resorcinol-formaldehyde resin. The lower value of CTE in ceramer is due to existence of silica and resorcinol -formaldehyde in co-continuous phase. Unidirectional composites prepared with ceramer matrix and high-strength carbon fibers show lower value of flexural strength at polymer stage as compared to those prepared with resorcinol-formaldehyde resin. However, after heat treatment to $1450^{\circ}C$, the ceramer matrix composites show large improvement in the mechanical properties, i.e. with 7% silicon in the ceramer, the flexural strength is enhanced by 100% and flexural modulus value by 40% as compared to that of pure resorcinol-formaldehyde resin matrix composites.

• Korean Journal of Organic Agriculture
• /
• v.22 no.1
• /
• pp.1-23
• /
• 2014

The purpose of this paper was to measure technical efficiencies and scale efficiencies of Korean seed industry by DEA method, and to identify the factors affecting the efficiencies by Tobit regression model. Survey data of 50 seed companies nationwide were applied for the analysis. The average score of overall technical efficiency for the surveyed companies in 2012 was 0.44, which is decomposed into pure technical efficiency 0.68 and scale efficiency 0.63. A majority of the seed companies exhibited at least one form of inefficiency except a few companies in optimal scale. It was also shown the most companies were operating in the stage of increasing returns to scale, which implies Korean seed companies are mainly in smaller scale than optimal. Additional results suggest that the Center for Private Seed Companies, which will be established at Gimje in 2015, plays an important role to make domestic seed companies improve their scale efficiency as well as pure technical efficiency by way of enlarging their size and co-using the high technology in the Center.

• Journal of Powder Materials
• /
• v.14 no.1 s.60
• /
• pp.19-25
• /
• 2007

This study was focused on the optimization of low-pressure ultrasonic spraying process for synthesis of pure ${\gamma}-Fe_2O_3$ nanoparticles. As process variables, pressure in the reactor, precursor concentration, and reaction temperature were changed in order to control the chemical and microstructural properties of iron oxide nanoparticles including crystal phase, mean particle size and particle size distribution. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies revealed that pure ${\gamma}-Fe_2O_3$ nanoparticles with narrow particle size distribution of 5-15 nm were successfully synthesized from iron pentacarbonyl ($Fe(CO)_{5}$) in hexane under 30 mbar with precursor concentrations of 0.1M and 0.2M, at temperatures over $800^{\circ}C$. Also magnetic properties, coercivity ($H_c$) and saturation magnetization ($M_s$) were reported in terms of the microstructure of particles based on the results from vibration sampling magnetometer (VSM).