• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.182-192
• /
• 2001

During the deep drawing process an initially flat blank is clamped between the die and the blank holder after which the punch moves down to deform the clamped blank into the desired shape. In general, sheet metal forming may involve stretching, drawing, bending or various combinations of those basic modes of deformation. The deformation problems of sheet metal working involve non-linearity in geometry and material. In this work, The punch load and thickness strain of electro-galvanized sheet steel (SECD) for elliptical deep drawing are examined under the various process conditions including, punch shape radius, die shape radius. The changes of punch load and thickness strain distribution of the deformed elliptical cup are affected by the size of each die shape radius.

• Design & Manufacturing
• /
• 제16권3호
• /
• pp.28-33
• /
• 2022

The recent increasing application rate of advanced high-strength steel(AHSS) for automotive parts makes it difficult to ensure the durability of forming tools. Significant load and friction generated during the piercing process of AHSS increase the wear rate and the damage degree to dies. These harsh process conditions also yield product failures, such as dimensional inconsistency of pierced holes and insufficient quality of hole's sheared edge. This study analyzed the effect of punch wear on the sheared surface of pierced parts and the forming load during the piercing process. Wear-shaped punches showed approximately 20% higher piercing load than normal-shaped punches, and the rollover ratio of the sheared surface also increased. It is considered that the dull edge of wear-shaped punches does not penetrate directly into the material but shears after tensioning it in a piercing direction. In addition, wear-shaped punches experienced compressive load even after completing the piercing process during the down-stroke and tensile load during the up-stroke. This load variation is related to the smaller diameter piercing holes produced by wear-shaped punches compared to normal-shaped punches. Thus, we demonstrated the predictability of the wear level of dies through a comparative analysis of the piercing load pattern.

• 소성∙가공
• /
• 제14권1호
• /
• pp.57-64
• /
• 2005

This study deals with the cold forging process design for shaft in the main part of automobile motors with rectangular deep groove. In forging process, the accuracy and die lift is very important because it have influence on reduction of the production cost and the increase of the production rate. Therefore, it is necessary to develop the manufacturing process of shaft by cold forging., process variables are the cropped face angle of billet and the eccentric load of punch. The former is derived from cropping test, the latter is occurred by clearance between container and preform. Also, grooved preform select the process variable for decrease in punch deflection. We investigate that a deflection of punch and a deformation of preform to every process variables. Through this investigation, we suggest the optimal preform and process design, expect to be improved the tool life in forging process.

• 소성∙가공
• /
• 제21권2호
• /
• pp.89-95
• /
• 2012

To examine the deformation characteristics of round aluminum pipe under biaxial compression, a horizontal biaxial compression die was fabricated. The change of material properties, punch load and deformation behavior were monitored in experiments using various compressive deformation rates in the range of 1mm/min.~400mm/min. The tensile and compressive strains were estimated from Vickers microhardness results. The punch load and deformation characteristic of the round aluminum pipes were found to change greatly at a deformation rate of about 200mm/min. The punch load decreased with increasing compressive deformation rate. Results of numerical simulation using Deform-2D were in good agreement with experimental results, and the measured hardness variation with the strain variation was predicted well by the simulation.

• 소성∙가공
• /
• 제22권2호
• /
• pp.67-73
• /
• 2013

The deformation characteristics and microstructure changes in a round copper pipe under biaxial compression was studied using a horizontal compression die. The change of material properties, punch load and deformation behavior were monitored using various compressive deformation rates in the range of 0.5mm/min.~450mm/min. The strains, either tensile or compressive, were estimated from Vickers microhardness test results. The punch load and deformation characteristics of the round copper pipes were found to change greatly at a deformation rate of about 200mm/min. The punch load decreased with increasing compressive deformation rate. The results of numerical simulations agreed well with what was expected from the final microstructure and the hardness profile estimated from the final deformation strains.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1753-1762
• /
• 2000

An inverse method is presented to obtain material's flow properties by using small punch test. This procedure employs, as the objective function of inverse analysis, the balance of measured load-di splacement response and calculated one during deformation. In order to guarantee convergence to global minimum, simulated annealing method was adopted to optimize the current objective function. In addition, artificial neural network was used to predict the load-displacement response under given material parameters which is the most time consuming and limits applications of global optimization methods to these kinds of problems. By implementing the simulated annealing for optimization along with calculating load-displacement curve by neural network, material parameters were identified irrespective of initial values within very short time for simulated test data. We also tested the present method for error-containing experimental data and showed that the flow properties of material were well predicted.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.193-198
• /
• 2000

The small punch test have been developed to evaluate the material strength of the power plant components. This small punch test specimen is very small than the conventional strength test specimens. Korea Electric Power Research Institute (KEPRI) have been applying this test to assess accurately the life of thermal power plant and enhancing the reliability. The small punch test for gas turbine blades is under development. It's possible to compare the relative strength among the same materials having different operation histories. In this paper, the strength reductions of gas turbine materials are investigated by the small punch tests. All materials shows the almost same strength and deformation with the allowable deviation. At the same test temperature, the damaged material has the maximum load value. The strength reduction is not shown in this small punch test results.

• 한국산학기술학회논문지
• /
• 제20권9호
• /
• pp.517-524
• /
• 2019

오버드라이버 허브클러치는 자동차 6단 자동 변속기 미션에 장착되어 엔진의 여유출력을 이용해 연료사용을 절감시켜주는 부품이다. 본 연구에서는 오버드라이버 허브클러치 제품에 대해 피어싱 공정 중 펀치에 가해지는 하중 및 소재 처짐량을 최소화 하고자 한다. 공정 중 펀치의 하중과 처짐량에 영향을 줄 수 있는 다이 클리어런스(die clearance)와 전단각도(shear angle) 그리고 마찰계수(friction coefficient)를 설계 변수로 설정했다. 또한 펀치의 하중과 소재 처짐량에 대해 각 설계 변수들의 영향도를 확인하기 위해 민감도 분석(sensitivity analysis)을 진행했다. 그 결과 전단 각도, 마찰 계수, 다이 클리어런스 순으로 하중 및 처짐량에 대해 민감한 것으로 조사되었다. 이를 통해 펀치의 하중과 소재 처짐량을 목적함수로 설정하고, 반응표면법(Response Surface Method)을 통해 각 설계 변수들과 목적함수의 방정식을 도출했다. 이를 통해 설정된 설계 변수들의 최적 값을 도출해 유한요소해석에 적용한 결과 펀치의 하중 및 소재의 처짐량이 기존대비 22.14% 개선됐다.

• Structural Engineering and Mechanics
• /
• 제78권2호
• /
• pp.135-143
• /
• 2021

In this study, continuous contact problem in the functionally graded (FG) layer loaded with a FG flat punch resting on the elastic semi-infinite plane was analyzed by the finite element method (FEM). It was assumed that the shear modulus and density of the layer and punch varied according to exponentially throughout their depth. FG layer's weight was included to the problem and additionally all surfaces were considered as frictionless. Analysis of FG materials was performed with a special macro which was added to the ANSYS program. Firstly, the shear modulus of the punch was considered to be very rigid and the results of initial separation load (λcr) and distance (xcr) were compared with the analytical solution. Afterwards, results obtained from the contact analysis made according to the inhomogeneity parameters (β, γ) between FG punch-FG layer which had been unprecedented in the literature were discussed. As a result, FG punch's stress values at the punch edges where stress accumulations occurred were found to be smaller than the rigid punch. The security of the structure, longer life of the material and ease of production are directly related to the reduction of the stress values. The results obtained in this study are important in this respect. Also this work is the first study that investigates the effect of FG punch on the FG layer.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.182-185
• /
• 2004

Based on the experimental observation, the mathematical friction model, which is an essential information for analyzing the forming process of sheet metal, is developed considering lubricant viscosity, surface roughness and hardness, punch corner radius, and punch speed. By comparing the punch load found by FEM with a proposed friction model with experimental measurement when the coated and uncoated steel sheets are formed in 2-D geometry in dry and lubricant conditions, the validity and accuracy of the developed friction model are demonstrated.